JVC RX-8020VBK Instructions Manual page 110

From the remote control:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
Adjustment is also possible without outputting the test tone. In this
case, you can skip steps 2 and 6 below.
1. Press SOUND.
"SOUND" appears on the remote control display
window.
• The 10 keys are activated for sound adjustments.
2. Press TEST to check if you can
hear the sounds through all the
speakers at equal level.
A test tone comes out of the speakers (only if the speakers are
activated) in the following order:
FRNT L (Left front speaker) = CENTER (Center speaker) =
FRNT R (Right front speaker) =
SURR R (Right surround speaker)
SBK R (Right surround back speaker) * =
SBK L (Left surround back speaker) or
S BACK (surround back speaker) *
SURR L (Left surround speaker) = (Back to the beginning)
* If you have selected "1SPK" for the surround back speaker (see
page 22), "S BACK" appears instead of "SBK L" and "SBK R."
No test tone outputs from the right surround back speaker.
3. Select a speaker you want to adjust.
The selected speaker name appears on
the remote's display for a while.
• To select the left front speaker, press
FRONT•L. "FRL" appears on the
remote control display window.
• To select the center speaker, press
CENTER. "CTR" appears on the
remote control display window.
• To select the right front speaker,
press FRONT•R. "FRR" appears on
the remote control display window.
• To select the right surround speaker, press SURR•R.
"SURRR" appears on the remote control display window.
• To select the right surround back speaker, press SBACK•R.
"SBKR" appears on the remote control display window.
• To select the left surround back speaker, press SBACK•L.
"SBKL" appears on the remote control display window.
• To select the left surround speaker, press SURR•L. "SURRL"
appears on the remote control display window.
Note:
If you have selected "1SPK" for the surround back speaker (see
page 22), press SBACK•L to adjust the surround back speaker
output level.
4. Press LEVEL + or – to adjust the
speaker output level (–10 dB to
+10 dB).
41
5. Press SOUND again then repeat steps 3
6. Press TEST again to stop the test
SOUND
Notes:
• If you have selected "NO" or "NONE" for a speaker (see page 22),
• Subwoofer output level cannot be adjusted when
TEST
4
MENU
• Test tone does not output through the speakers when selecting
=
On the front panel:
=
You can also use the buttons on the front panel to adjust the speaker
output levels. However, no test tone is available when using the
buttons on the front panel. So make adjustments while listening to
the sound of the source played back.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
∗ ∗
FRONT•L FRONT•R
2 3
MENU
1. Press LEVEL ADJUST repeatedly to
∗ ∗
CENTER
SUBWFR
5 6
ENTER
∗ ∗
SURR•L SURR•R
8 9
∗ ∗
Q SBACK•L SBACK•R
0
+10
100 +
FM MODE
2. Press CONTROL UP 5 or
3. Repeat steps 1 and 2 to adjust the
+
∗
CH/ LEVEL
−
and 4 to adjust the other speakers
output levels.
tone.
test tone does not come out of the corresponding speaker.
outputting test tone. When you adjust the
subwoofer output level, press SOUND, SUBWFR
then LEVEL + or – to adjust the speaker output
level (–10 dB to +10 dB). ("S-WFR" appears on the
remote control display window.)
It is recommended to make adjustments while listening to the
sound of the source played back.
DVD MULTI.
select a speaker you want to adjust.
• Each time you press the button, the items change
as follows.
SUBWFR (Subwoofer) = FRNT L (Left front speaker) =
CENTER (Center speaker) = FRNT R (Right front speaker) =
SURR R (Right surround speaker)
SBK R (Right surround back speaker) * =
SBK L (Left surround back speaker) or
S BACK (surround back speaker) *
SURR L (Left surround speaker) = (Back to the beginning)
* If you have selected "1SPK" for the surround back speaker (see
page 22), "S BACK" appears instead of "SBK L" and "SBK R."
DOWN ∞ to adjust the speaker
output level (–10 dB to +10 dB).
other speakers output levels.
SOUND
TEST
4
MENU
∗
SUBWFR
6
L LEVEL
ADJUST
=
=
CONTROL
DOWN UP