This NX-800H (K3 version) service manual contains a number of sections which differ from the service manual (B51-8823-00) for NX-800/800H (K version). For items other than those in this NX-800H (K3 version) service manual, please refer to the ser- vice manual (B51-8823-00) for NX-800/800H (K version).
Neither is any liability assumed for dam- the fi rmware under the license of Digital Voice Systems, Inc. ages resulting from the use of the information contained herein. Kenwood reserves the right to make changes to any products herein at any time for improvement purposes. GENERAL...
Page 3
Control station. The antenna system selection depends on many factors and is beyond the scope of this manual. Power input Your KENWOOD dealer can help you select an antenna sys- connector tem that will best serve your particular needs. 4-2. Radio location...
NX-800H SYSTEM SET-UP Merchandise received Frequency range RF power Type Choose the type of transceiver 380.0~400.0MHz Are you using KRK-10 the remote kit? (Option) Are you using KCT-46 the ignition sense cable? (Option) See page 5. Transceiver programming A personal computer, programming interface (KPG-46/46A), and programming software (KPG-111D) are required for programming.
NX-800H REALIGNMENT 1. Modes 5. PC Mode 5-1. Preface User mode The transceiver is programmed by using a personal com- puter, programming interface (KPG-46/46A) and program- Panel test mode Panel tuning mode ming software (KPG-111D: ver. 1.80 or later). The programming software can be used with a PC. Fig- ure 1 shows the setup of a PC for programming.
NX-800H REALIGNMENT 5-3. KPG-46/KPG-46A description 7. If writing ends successfully, the checksum is calculated and a result is displayed. (PC programming interface cable: Option) 8. If you want to continue programming other transceivers, The KPG-46/46A is required to interface the transceiver repeat steps 4 to 7.
CIRCUIT DESCRIPTION 1. Overview 2. Frequency Confi guration NX-800H (K3) is a UHF Mobile transceiver designed to The receiver is a double-conversion super heterodyne operate in the frequency range of 380 to 400MHz (in user using first intermediate frequency (IF) of 58.05MHz and mode).
NX-800H PARTS LIST ✽ New Parts. indicates safety critical components. L : Scandinavia K : USA P : Canada Parts without Parts No. are not supplied. Y : PX (Far East, Hawaii) T : England E : Eu rope Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Page 9
NX-800H PARTS LIST DISPLAY UNIT (X54-3680-10) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation C966,967 CK73HB1H102K CHIP C 1000PF R953 RK73GB2A271J CHIP R 1/10W R954 RK73GB2A470J CHIP R...
Page 10
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation CK73HB1H471K CHIP C 470PF TX-RX UNIT (X57-7750-18) CC73HCH1H100B CHIP C 10PF CK73HB0J105K CHIP C 1.0UF...
Page 11
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation C194 CK73HB1H471K CHIP C 470PF C292 CK73HB1H471K CHIP C 470PF C201 CK73HB1E103K CHIP C 0.010UF...
Page 12
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation C435 CK73FB1A106K CHIP C 10UF C551 CK73HB1E103K CHIP C 0.010UF C436 CS77BA1A100M CHIP TNTL...
Page 13
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation C736 CC73HCH1H101J CHIP C 100PF C922,923 CK73HB1H102K CHIP C 1000PF C737 CK73HB1A104K CHIP C 0.10UF...
Page 14
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation L208 L92-0138-05 CHIP FERRITE RK73HB1J271J CHIP R 1/16W L209 L40-3975-92 SMALL FIXED INDUCTOR (39NH)
Page 15
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation R140 RK73HB1J104J CHIP R 100K 1/16W R265 RK73HB1J103J CHIP R 1/16W R141 RK73HB1J124J CHIP R...
Page 16
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation R410 RK73HB1J684J CHIP R 680K 1/16W R545 RK73HB1J000J CHIP R 1/16W R411 RK73HB1J104J CHIP R...
Page 17
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation R652 RK73HB1J104J CHIP R 100K 1/16W R755 RK73HB1J103J CHIP R 1/16W R654 RK73GB2A000J CHIP R...
Page 18
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation R827 RK73HB1J332J CHIP R 3.3K 1/16W D909 1SS355 DIODE R828 RK73HB1J000J CHIP R 1/16W...
Page 19
NX-800H PARTS LIST TX-RX UNIT (X57-7750-18) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation SSM6L05FU-F SSM3J05FU-F Q9,10 2SC5636 TRANSISTOR 2SK1215-E(E) Q101 2SC5108(Y)F TRANSISTOR Q102 2SC5455-A TRANSISTOR Q105 RT1N141U-T111...
NX-800H EXPLODED VIEW : N09-2292-05 M3 x 8 : N67-3008-48 M2.6 x 6 (Br-Tap) : N87-2606-43 M2.6 x 8 (Br-Tap) : N87-2608-48 IC715 IC403 IC102 TX-RX unit A/2 (X57-) TX-RX unit B/2 (X57-) Display unit (X54-) Parts with the exploded numbers larger than 700 are not supplied.
NX-800H ADJUSTMENT Controls “FNC” not appears on the sub LCD display Function Display Power switch Microphone key Volume Up/Down key Channel Up/Down key [PTT] Transmit Use as the DTMF keypad. [0] to [9] If a key is pressed during and [A]...
Page 22
NX-800H ADJUSTMENT ■ Frequency and Signaling Panel Tuning Mode The transceiver has been adjusted for the frequencies ■ Preparations for tuning the transceiver shown in the following table. When required, readjust them Before attempting to tune the transceiver, connect the following the adjustment procedure to obtain the frequen- unit to a suitable power supply.
Page 23
NX-800H ADJUSTMENT ■ 5 reference level adjustments frequency Tuning point RX (MHz) TX (MHz) 335.05000 335.10000 Note: Low’ 347.55000 347.60000 Although the frequency range of this transceiver is 380 to 400MHz, the circuit and adjustments are designed under Center 365.05000 365.10000...
Page 24
NX-800H ADJUSTMENT Adjustment Item Description RSSI display level “ “ is adjusted. Low RSSI Both “Low RSSI” and “High RSSI” must be adjusted. High RSSI (The curve data of RSSI level is applied.) Tight Squelch The squelch level at level “9” is adjusted.
Page 25
NX-800H ADJUSTMENT Aw (Analog An (Analog Nn (NXDN Nv (NXDN Adjusutment Main LCD Very Narrow) Adjust item Wide) Narrow) Narrow) Order Sub-LCD display item display Number Adjustment range (RSSI measurement Receive Sensitivity 1 SENS1 value) Section 2 1~256 (RSSI measurement...
Page 27
NX-800H ADJUSTMENT Test Equipment Required for Alignment Test Equipment Major Specifi cations Frequency Range 300 to 520MHz Modulation Frequency modulation and external modulation 1. Standard Signal Generator Output –127dBm/0.1µV to greater than –20dBm/22.4mV (SSG) When performing the Frequency adjustment, the following accuracy is necessary.
Page 28
NX-800H ADJUSTMENT Radio Check Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel test mode PC test mode Unit Terminal Unit Parts Method equipment 1. Frequency 1) CH-Sig: 1-1 1) Test Channel f. counter Panel Check an internal +0.05/+0.55ppm...
Page 29
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel test mode PC test mode Unit Terminal Unit Parts Method equipment 5. Sensitivity 1) CH-Sig : 1-1 1) Test Channel Check 12dB SINAD or check SSG output Channel: 1...
Page 30
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 5. Frequency * The Frequency 1) Adj item: [PC test mode] [PC test mode] adjust adjustment can be...
Page 31
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 2. Low 1) Adj item: [LOLMT] 1) Adj item: [Low Trans- Power [Panel 25.0W ±1.0W Transmit Adjust: [✳✳✳✳]...
Page 32
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 5. Balance 1) Adj item: [BAL] 1) Adj item: [Balance] Deviation [Panel The Deviation of 2kHz Tone deviation adjust *2 Adjust: [✳✳✳]...
Page 33
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment [Wide] 1) Adj item: [Aw ADEV] 1) Adj item: [Maximum Deviation [Panel Write the same 4150~4250Hz Adjust: [✳✳✳✳]...
Page 34
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 10. LTR 1) Adj item: [An LTR] 1) Adj item: [LTR Deviation [Panel Write the value as 0.70~0.80kHz...
Page 35
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment [Wide] 1) Adj item: [Aw MSK] 1) Adj item: [MSK Deviation [Panel Write the value as 2.95~3.05kHz Adjust: [✳✳✳✳]...
Page 36
NX-800H ADJUSTMENT Receiver Section Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1. AF level [Panel test mode] 1) Test Channel [Panel Volume Up/Down 2.83V±0.3V setting 1) CH-Sig: 1-1 Channel: 1 Ext.SP...
Page 37
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment [NXDN 1) Adj item: [Nv RRSSI] 1) Adj item: [RSSI Ref- [Panel [Panel tuning mode] Adjust with the ana- Very Adjust: [✳✳✳]...
Page 38
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 6. Low RSSI 1) Adj item: [An LRSSI] 1) Adj item: [Low [Panel tuning mode] at –118dBm Adjust: [✳✳✳]...
Page 39
NX-800H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment [Analog 1) Adj item: [Aw HRSSI] 1) Adj item: [High [Panel tuning mode] Wide] Adjust: [✳✳✳] RSSI (Wide)] Ext.SP...
NX-800H PC BOARD DISPLAY UNIT (X54-3680-10) Component side view (J79-0157-39) LEFT D929 D914 C922 R922 D935 DM/KVL HK/RXD LEFT DOWN PTT/TXD BLC/AFO DISPLAY UNIT (X54-3680-10) Foil side view (J79-0157-39) CP909 R907 IC905 R963 D904 R952 R935 C927 C948 CP917 IC901...
Page 62
NX-800H SCHEMATIC DIAGRAM TX-RX UNIT (X57-7750-18) (A/2) IC715 LA4425A AF POWER 13.54V 1.34V 6.38V CN705 R831 C810 TX-RX UNIT (X57-7750-18) (B/2): D-SUB25 470p D901 D903 D907 D911 J701 LINE LINE LINE LINE PROTECTION PROTECTION PROTECTION PROTECTION (BER CK) (AUXIO1) (AUXIO3) (AUXIO8) EXT.SP...
Page 63
NX-800H SCHEMATIC DIAGRAM DISPLAY UNIT (X54-3680-10) R924 R925 "PF4" VOL UP R922 CN902 CH UP "PF3" VOL DOWN R923 CH DOWN "PF2" "PF1" TX-RX UNIT (X57-7750-18) (A/2) CN597 CN901 D908,911,912 KEY MATRIX C580 100p 3.12V C581 POWER 1000p C582 1000p...
Page 64
NX-800H SCHEMATIC DIAGRAM DISPLAY UNIT (X54-3680-10) 8.00V 7.97V Q910 12A02CH TX/RX LED 7.27V BACK TX/RX LED (BUSY) LIGHT (TX) Q905 Q906 R :0V R : 5.00V D915-926 D927-936 RT1N141U RT1N141U T : 5.00V T : 0V -T111 -T111 BACK LIGHT...
NX-800H LEVEL DIAGRAM Audio Frequency –82.0dBm –82.0dBm 186mVrms 226mVrms 226mVrms 96mVrms 4.00Vrms (EVOL) IF AMP (ASIC) (RXAF SMF) (RX SUM) VOL=20 (SP AMP) IC201 IC510 IC701 IC711 IC712 IC715 J701 AF VTVM AF level obtained when the AF output level is adjusted for 4.00V/4Ω...
FM Hum and Noise (Typ) ......Analog @25kHz: 50dB Analog @12.5kHz: 45dB Modulation ..........16K0F3E, 14K4F1D, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D Analog measurements made per TIA/EIA 603 and specifi cations shown are typical. KENWOOD reserves the right to change specifi cations without prior notice or obligation.
Page 72
Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road, Bp 58416 Villepinte, 95944 Roissy Ch De Gaulle Cedex Kwai Fong, N.T., Hong Kong KENWOOD House, Dwight Road, Watford, Herts., 1 Ang Mo Kio Street 63, Singapore 569110 WD18 9EB United Kingdom...