Brother DCP-J125 Quick Setup Manual

Unpack the machine and check the components
1
Start Here
WARNING indicates a
potentially hazardous
a.
WARNING
situation which, if not
avoided, could result in
death or serious injuries.
b.
c.
c.
Press and slide the
paper side guides
1
a and paper length
guide b to fit the
paper size.
3
Make sure that the
triangular marks c
2
on the paper side
guides a and paper
length guide b line
up with the mark for
the paper size you
are using. 3
Install the ink cartridges
6
a. c.
The LCD shows No Ink Cartridge. Remove the green protective part a.
b.
Open the ink cartridge cover a.
Note
1
Do not throw away the green protective part.
You will need it if you transport the machine.
Check the print quality
7
a. b.
When the preparation process has Check the quality of the four colour blocks a
finished, the LCD shows on the sheet.
Set Paper and Press Start. (black/yellow/cyan/magenta)
Press Colour Start.
If all lines are clear and visible,
o
press (Yes) to finish the quality
check.
If you can see missing short lines,
o
press (No) and follow the steps
on the LCD.
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
LX6274054
CEE-ENG
Printed in China
Note
• Save all packing materials and the box in case for any
reason you must ship your machine.
• A USB cable is not included.
You need to purchase a USB 2.0 cable that is no more
than 2 metres long.
Remove the protective tape and film covering the
machine, and also from the LCD.
The components of your box may differ depending on your country.
Remove the plastic bag a containing the ink cartridges
1 Approx. 65% yield of the replacement cartridge. For details, see Consumable items in the Basic
User's Guide.
from on top of the paper tray.
WARNING
Make sure you have all components.
Plastic bags are used in the packaging of your machine. To avoid
danger of suffocation, please keep these bags away from babies
and children.
d.
Fan the stack of paper well.
e.
Gently put the paper into
the paper tray. Check that
the paper is flat in the tray.
f.
Gently adjust the paper side
guides to the paper with
both hands.
Make sure the paper side
guides touch the edges of
the paper.
IMPORTANT
DO NOT push the paper in too far.
d.
Unpack the ink cartridge.
Turn the green knob on the protective yellow cap clockwise until it clicks to release the vacuum
seal, then remove the cap a.
1
1
Set the LCD contrast (if needed)
8
a.
Press Menu.
b.
Press a or b to choose
General Setup, and then press OK.
1
c.
Press a or b to choose
LCD Settings, and press OK.
d.
OK Press a or b to choose
LCD Contrast, and then press OK.
e.
Press d or c to choose the contrast level,
and then press OK.
Poor
f.
Press Stop/Exit.
Attachment of the cover of
2
Inbox Ink Cartridges [x4] 1
1
Black
Yellow
Cyan
Magenta
Installation CD-ROM
Power Cord
Documentation CD-ROM
Control Panel
g. h.
Close the output paper tray Pull out the paper support a
cover and slowly push the until it clicks, and then unfold
the paper support flap b.
paper tray back into the
machine.
Note
Make sure you install the Inbox Ink Cartridges
included with your machine fi rst.
Set the date and time
9
a.
Press Menu.
b.
Press a or b to choose
Initial Setup, and
then press OK.
c.
Press a or b to choose
Date&Time, and then
press OK.
Load plain A4 paper
the control panel 3
a.
Pull out the paper tray.
a.
Attach the cover of the control
panel to the machine.
Connect the power cord
4
a.
Connect the power cord.
WARNING
The machine must be fi tted with an earthed plug.
IMPORTANT
DO NOT connect the
USB cable yet.
2
Note
1
The Warning LED on the
control panel will stay on
until you have installed
the ink cartridges.
e.
Install each ink cartridge in the direction of the arrow on the label.
Take care to match the colour of the lever a with the cartridge
colour b.
1
2
e.
d.
To enter the last two digits of the year, press Repeat for month/day/time in 24-hour format.
a, b, d or c to select a number and press OK.
f.
Press Stop/Exit.
To save the year, press a, b, d or c to select
and press OK.
OK OK
Note
Year:2010
If you make a mistake and want to start again,
1 2 3
press Stop/Exit to go back to step a.
4 5 6
7 8 9
0 OK OK
(e.g. Enter 10 for 2010.)
Quick Setup Guide
DCP-J125
b.
Lift the output paper tray cover a.
1
Choose your language
5
a.
Press a or b to choose your
language and press OK.
b.
Press a or b to choose Yes
or No and press OK.
Note
If you set the wrong language,
you can change it again after
setting the date and time.
(For details see Changing LCD
language in chapter 1 in the
Advanced User's Guide on the
documentation CD-ROM.)
f.
Gently push the ink cartridge until it clicks. After all the ink
cartridges are installed close the ink cartridge cover.
Note
The machine will prepare the ink tube system for printing.
This process will take approximately four minutes.
Do not turn off the machine.
Turn the sheet over.