Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
Contents S S a a f f e e t t y y P P r r e e c c a a u u t t i i o o n n s s ..................3 3 M M o o n n i i t t o o r r C C o o n n t t r r o o l l F F u u n n c c t t i i o o n n Power .
Kenwood dealer. • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer. FCC WARNING This equipment may generate or use radio frequency energy.
Monitor Control Function V.SEL MODE SCRN Phone Jack (Ø3.5) Power Turning on the power Press the PWR button. Turning off the power Press the PWR button for at least one second. Switching the Monitor’s Picture Each time you press the V.SEL button, the monitor’s picture switches as follows: ●When the Video Box Unit is connected ▼...
<On Screen Display> If the monitor's buttons operated while a TV, video or navigation picture is displayed, the receiving channel No., the picture settings, AV output settings, etc., are superimposed on the picture . Tuning mode TV band Screen mode Speaker mode NOTE Tuning mode,TV band, and Channel No.: When the KTC-V800N/ KTC-V800P is connected.
System Setup Function V.SEL MODE SCRN Phone Jack (Ø3.5) Setting the System ●When the Video Box Unit is connected Press the SCRN button for at least one second to switch to the setup menu screen. Touch [ SYSTEM ] to switch to the system setting screen.
S Y S T E M T O U C H S E T U P Setup Menu Screen < Video Box Unit or KTC-V800N> Setting the Touch Sensor Tone [BEEP] Touch [ ON ] or [ OFF ] to switch the function on and off.
TV Control Function TV picture screen Switching to the TV Control Screen Press the V.SEL button repeatedly to select the TV picture. Touch the part C to switch to the TV control screen. Selecting the Preset Bands Each time you touch [ BAND ], the preset band switches between the TV1 and TV2.
Selecting the Channels on the TV Picture Screen Selecting the Preset Bands Each time you touch part B, the preset band switches between the TV1 and TV2. Selecting the Channels Auto Seek Tuning (AUTO1) Touch the part D to seek for channels up the band. Touch the part A to seek for channels down the band.
Page 10
Remote Control Function 2CAUTION Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries 1. Use two "AA" batteries: Slide the cover while pressing downwards to remove it as illustrated. 2. Insert the batteries with the ª and · poles aligned properly following the illustration inside the case.
Installation Accessories External view ... Number of items ...1 ...1 ...1 Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery. 2. Make the proper input and output cable connections for each unit.
Installation Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A. Do not install in locations where the entire support is at a diagonal such as in Figure B or where the monitor unit is facing down such as in Figure C.
Installation for the Video Box Unit ■ Securing to audio board Accessory 5 (Ø4 x 16 mm) Accessory 7 2CAUTION Please do not install the unit near the dashboard, the rear tray, or other important components. Doing so could lead to injury or accident should the unit come off due to a shock and strike a person or an important component. Tapping screws(Accessory 5) should be used for mounting.
Installation Connecting the Headphone / AV Equipments ■ Connecting the Headphone Stereo Mini Plug (Ø3.5) ■ Connecting the AV Equipment Audio/Visual Output • Audio right output (Red) • Audio left output (White) • Visual output (Yellow) Audio/Visual input 2 • Audio right intput (Red) •...
Wait a while after turning power on for the temperature to rise. Normal brightness will return. • Separate the two antennas as far as possible. • Turn off the LZ-800W. SOLUTION power“ (See page 13).
Specifications Specifications subject to change without notice. Monitor Unit Screen size ...8.0 inches wide Display system ...Transparent TN LCD panel Drive system ...TFT active matrix system Number of pixels ...336.960 pixels (480 H x 234 V x RGB) Effective pixels...99.99% Pixel arrangement...RGB striped arrangement Back lighting ...Cold cathode tube Phone jack (Miniplug x 1) Audio output level...Stereo Mini Jack / 820 mV/32 Ω...