Yamaha MCX-2000 Owner's Manual page 94

Front Panel Display
1 Frorn the User Interface nlenu, select Front Panel Display.
2 Change each parameter value as needed.
o
Backlight
fvlake the display back.light either Bri£jrlt or Dark:.
fJ
Contrast
Set the
disp~ay
contrast as you can clear!:! see it (0-50; factory
setting: 25). Be sure that an extrernely high or iovv value nlakes
your display hard to be seen.
3 Your change is reflected in real time. When you select
OK: the ':Saving ...
~'
message is shown and new settings
are stored.
Page Displayed at Power ON
1 From the User Interface menu, select Page displayed at
Power ON.
2 You have just one parameter, Open the last page
displayed, for this setting. Select ON if you want the last
shown screen to be displayed when the MCX-2000 is
connected to the AC pOvver source or waking up from
sleep or standby mode. Select OFF if you want the Top
rv1enu screen to be displayed (factory setting).
3 When you select OK: the ':Saving ... H message is shown.
The
~JlCX-2000
afterward shows a screen as specified
here,
94
r\.~CX-2DOC
OV,fner':5
IvlGnuo~
Screen Saver
1 From the User Interface rnenu, select Screen Saver.
2 Change each parameter value as needed.
o
Use Screen Saver
Specify vvllether you use the screen saver, Select ON if you \N8f1t
the scr'een dsplay to go off after the specifiec! duration even
vvhHe the
f\r1CX.-2000
is active (factory setting), Select
OFF if
you
vV3nt tr'le screen display to go off only vvllen the MCX-2000
enters sleep or standby fTlode. If you select ON: specify the
duraton \Nith the follo\Ning pararreter
(unavai~able vv~tr1
OFF),
e
Delay before activation
SpecJy the duration of the screen display before the screen
saver is activated (1 nlinute·- 60 frinutes; factory setting:
10
r'ninutes).
3 When you select OK, the ;'Saving... H message is shown,
The MCX-2000 afterward turns on and off the display as
speci'fied here.
~.IiIill
VYhen shipped, L1' 1 8 \:1CX-2COO is set to activate t1'1e scr-een saver" in 10
trlinui:es. So, y-cu'-
T-/
monitor" sCr"een wil! automaticaJy qo off in
10
minutes even whi1e t1,e MCX<?OOO continues
enter' sleep mode. VYhen you cper-ate the
Lho unit cancels the scnJon savm D.nO
Front Panel Display
1 Frorn the User Interface nlenu, select Front Panel Display.
2 Change each parameter value as needed.
o
Backlight
fvlake the display back.light either Bri£jrlt or Dark:.
fJ
Contrast
Set the
disp~ay
contrast as you can clear!:! see it (0-50; factory
setting: 25). Be sure that an extrernely high or iovv value nlakes
your display hard to be seen.
3 Your change is reflected in real time. When you select
OK: the ':Saving ...
~'
message is shown and new settings
are stored.
Page Displayed at Power ON
1 From the User Interface menu, select Page displayed at
Power ON.
2 You have just one parameter, Open the last page
displayed, for this setting. Select ON if you want the last
shown screen to be displayed when the MCX-2000 is
connected to the AC pOvver source or waking up from
sleep or standby mode. Select OFF if you want the Top
rv1enu screen to be displayed (factory setting).
3 When you select OK: the ':Saving ... H message is shown.
The
~JlCX-2000
afterward shows a screen as specified
here,
94
r\.~CX-2DOC
OV,fner':5
IvlGnuo~
Screen Saver
1 From the User Interface rnenu, select Screen Saver.
2 Change each parameter value as needed.
o
Use Screen Saver
Specify vvllether you use the screen saver, Select ON if you \N8f1t
the scr'een dsplay to go off after the specifiec! duration even
vvhHe the
f\r1CX.-2000
is active (factory setting), Select
OFF if
you
vV3nt tr'le screen display to go off only vvllen the MCX-2000
enters sleep or standby fTlode. If you select ON: specify the
duraton \Nith the follo\Ning pararreter
(unavai~able vv~tr1
OFF),
e
Delay before activation
SpecJy the duration of the screen display before the screen
saver is activated (1 nlinute·- 60 frinutes; factory setting:
10
r'ninutes).
3 When you select OK, the ;'Saving... H message is shown,
The MCX-2000 afterward turns on and off the display as
speci'fied here.
~.IiIill
VYhen shipped, L1' 1 8 \:1CX-2COO is set to activate t1'1e scr-een saver" in 10
trlinui:es. So, y-cu'-
T-/
monitor" sCr"een wil! automaticaJy qo off in
10
minutes even whi1e t1,e MCX<?OOO continues
enter' sleep mode. VYhen you cper-ate the
Lho unit cancels the scnJon savm D.nO