Kenwood KVT-M707 Installation Manual
7-inch wide screen monitor receiver
Hide thumbs
Also See for KVT-M707:
- Installation manual (33 pages) ,
- Instruction manual (72 pages) ,
- Installation manual (72 pages)
Advertisement
Quick Links
KVT-M707
7-Inch WIDE SCREEN MONITOR-RECEIVER
INSTALLATION MANUAL
AMPLI-TUNER-MONITEUR GRAND ECRAN 7 pouces
MANUEL D'INSTALLATION
7-Zoll BREITBILD MONITOR-RECEIVER
INSTALLATION-HANDBUCH
7 inch BREEDBEELDMONITOR-RECEIVER
INSTALLATIE HANDLEIDING
SINTOLETTORE-MONITOR A SCHERMO AMPIO 7 pollici
MANUALE DI INSTALLAZIONE
REPRODUCTOR-MONITOR DE PANTALLA PANORÁMICA DE 7 pulgadas
MANUAL DE INSTALACION
RECEPTOR DE MONITOR DE ECRÃ LARGO de 7 polegadas
MANUAL DE INSTALAÇAO
© B54-4471-00/00 (EV)
Advertisement
Related Manuals for Kenwood KVT-M707
Summary of Contents for Kenwood KVT-M707
-
Page 1: Installation Manual
KVT-M707 7-Inch WIDE SCREEN MONITOR-RECEIVER INSTALLATION MANUAL AMPLI-TUNER-MONITEUR GRAND ECRAN 7 pouces MANUEL D'INSTALLATION 7-Zoll BREITBILD MONITOR-RECEIVER INSTALLATION-HANDBUCH 7 inch BREEDBEELDMONITOR-RECEIVER INSTALLATIE HANDLEIDING SINTOLETTORE-MONITOR A SCHERMO AMPIO 7 pollici MANUALE DI INSTALLAZIONE REPRODUCTOR-MONITOR DE PANTALLA PANORÁMICA DE 7 pulgadas MANUAL DE INSTALACION RECEPTOR DE MONITOR DE ECRÃ... - Page 2 Accessories ..1 ..1 ..1 ..1 ..1 ..1 ..1 ..2 ..4 ..4 ..2 English...
-
Page 3: Installation Procedure
Installation Procedure 1. To prevent a short circuit, remove the key from the 2WARNING ignition and disconnect the - battery. • If you connect the ignition wire (red) and the 2. Make the proper input and output wire connections battery wire (yellow) to the car chassis (ground), for each unit. - Page 4 Mute wire (Brown) Connect to the terminal that is grounded when either the telephone rings or during conversation. MUTE To connect the Kenwood navigation system, consult your navigation manual. (10A) Power control/ Motor antenna control cable (Blue/White)
- Page 5 Disc Changer etc. (Optional) Connection cable (Included in the disc changer) Receiver unit (rear side) Connection cable (Included in the Navigation system) Accessory 2 TV tuner (Optional) Connection cable (Included in the TV tuner) Dimmer control wire (Orange/White) Ignition wire (Red) Navigation System (Optional) Ground wire (Black) -...
- Page 6 Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated.
-
Page 7: Connection For Av Equipments
Connection for AV Equipments PRE OUTPUT AV OUTPUT REAR FRONT AV INPUT 2 VIDEO R-CAM V-IN FM /AM ANTENNA AV INPUT 1 POWER VIDEO VIDEO ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout •... - Page 8 Installation for Monitor Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Accessory 5 Self-tapping screw Metal mounting strap (commercially available) (commercially available) Make sure that the unit is installed securely in place.
- Page 9 Removing Monitor Unit ■ Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 6 Removal Tool (Accessory 6) and remove the two locks on the lower level. Lower the frame and pull it forward as shown Catch in the figure.
- Page 10 Installation of Remote control unit ■ Install the remote control unit holder (Accessory !). Double-stick tape (included) Remote control holder ! To prevent the Remote control unit from dropping down under your foot, install it using the Remote control unit holder.If the Remote control unit drops down under driving pedals, it will interfere with your driving and may result in a traffic accident.
- Page 11 English...