Electronic lockstitch bar tracker/electronic lockstitch belt loop bar tracker/electronic lockstitch pattern tracker/electronic lockstitch button sewer e series (198 pages)
Electronic lockstitch bar tacker; electronic lockstitch belt loop bar tacker; electronic lockstitch eyelet buttonhole end bar tacker; electronic lockstitch decorative pattern tacker (99 pages)
Electronic direct drive lockstitch bar tacker
electronic direct drive lockstitch button sewer (223 pages)
Summary of Contents for Brother KE-430FX
Page 1
KE-430FX Basic Operation Manual KE-430FS BE-438FX ELECTRONIC DIRECT DRIVE LOCKSTITCH BAR TACKER ELECTRONIC DIRECT DRIVE LOCKSTITCH BUTTON SEWER Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. This basic operation manual...
Page 2
Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions and the explanations given in the instruction manual. With industrial sewing machines, it is normal to carry out work while positioned directly in front of moving parts such as the needle and thread take-up, and consequently there is always a danger of injury that can be caused by these parts.
This symbol ( ) indicates something that you must do. The picture inside the circle indicates the ・・・・・・ nature of the thing that must be done. (For example, the symbol at left means “you must make the ground connection”.) KE-430FX/KE-430FS, BE-438FX...
Furthermore, do not excessively bend the cords or secure them too firmly Contact your Brother dealer or a qualified electrician with staples, otherwise there is the danger that fire or for any electrical work that may need to be done.
Furthermore, after tilting back the machine head, do Ask your Brother dealer or a qualified electrician to not push the face plate side or the pulley side from carry out any maintenance and inspection of the above, as this could cause the machine head to electrical system.
The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are difficult to read, please contact your nearest Brother dealer. *Safety devices...
3. LIST OF SEWING PATTERNS ..... 6-2. Program setting method ........36 6-3. Copying programs ........... 40 3-1. List of sewing patterns (KE-430FX・FS) ..3 6-4. Checking the sewing pattern 3-2. List of sewing patterns (BE-438FX) ....8 (KE-430FX・FS) ..........41 4.
(-03, -0K, -0F specifications). Page 31 This is used to stop the thread from pulling out at the sewing start, and at times when skipped stitches might easily occur. * The default setting for this memory switch is "OFF". KE-430FX/KE-430FS, BE-438FX...
3. LIST OF SEWING PATTERNS 3. LIST OF SEWING PATTERNS 3-1. List of sewing patterns (KE-430FX・FS) The sewing patterns shown below have been preset into the sewing machine and can be selected according to specifications. (Any sewing pattern is available as long as it is within the work clamp and feed plate in size.) Use the work clamp and feed plate that match the respective sewing pattern selected.
Page 12
* The sewing start and sewing end are in the middle of the pattern. Straight bar tacking Vertical zigzag stitching Tacking size (mm) Tacking size (mm) No. of No. of Pattern Pattern Length Width Length Width stitches stitches KE-430FX/KE-430FS, BE-438FX...
Page 13
3. LIST OF SEWING PATTERNS Vertical bar tacking Vertical straight bar tacking Tacking size (mm) Tacking size (mm) No. of No. of Pattern Pattern Length Width Length Width stitches stitches KE-430FX/KE-430FS, BE-438FX...
Width If you want to sew a sewing pattern other than standard sewing patterns, you can create your original pattern using the PS-300B. Consult with your local Brother sales office for details. Note when creating additional sewing patterns When sewing data with a small number of stitches (15 stitches or less) is sewn repeatedly (short cycle operation), the upper shaft motor may overheat and the “E150”...
― 10-10 12-12 *1 Use for buttons with small holes. *2 Check that the diameter of the holes in the buttons is 2 mm or greater before using the programs. *3 Do not use the button lifter spring. KE-430FX/KE-430FS, BE-438FX...
Page 17
*5 When sewing of one side is completed, the thread will be trimmed without the button clamp rising, and then the other side will be sewn. KE-430FX/KE-430FS, BE-438FX...
Page 18
Note when creating additional sewing patterns When sewing data with a small number of stitches (15 stitches or less) is sewn repeatedly (short cycle operation), the upper shaft motor may overheat and the “E150” error code may be generated. KE-430FX/KE-430FS, BE-438FX...
Furthermore, do not excessively bend the cable or secure it too firmly Contact your Brother dealer or a qualified electrician staples, otherwise there is the danger that fire or for any electrical work that may need to be done.
(4) is in the center of the hole (10) in the table for installing the oiler (8) as shown in figure [A]. NOTE: • Make sure that the dust oiler setting plate (4) does not interfere with the hinge holder (2). 2281B KE-430FX/KE-430FS, BE-438FX...
(11) Plain washers [3 pcs] (12) Screws [3 pcs] (13) Felt (14) Oil tube Pass the felt (13) and the oil tube (14) through the hole in the dust oiler setting plate (15) into the oiler (16). 3167B KE-430FX/KE-430FS, BE-438FX...
(2) Wood screws [4 pcs] * Pass the panel cord through the hole in the table, and then insert it into the control box through the hole in the side of the control box. (3) Staples [3 pcs] 2286B KE-430FX/KE-430FS, BE-438FX...
(4) Set screw 4410Q 4-8. Installing the eye guard CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices attached, injury may result. (1) Eye guard assembly (2) Screws [2 pcs] 2287B KE-430FX/KE-430FS, BE-438FX...
• Check that the connector is facing the correct way, and then insert it firmly until it locks into place. • Secure the cables with cable ties and cord clamps, while being careful not to pull on the connector. 2288B (Continued on next page.) KE-430FX/KE-430FS, BE-438FX...
Page 25
Y pulse motor [4-pin] Blue P22 (YPM) Work clamp pulse motor [4-pin] Black P23 (PPM) NOTE: Route the X, Y and work clamp pulse motor harnesses so that they do not touch the power supply P.C. board. (Continued on next page.) KE-430FX/KE-430FS, BE-438FX...
Page 26
Close the cord presser plate (2) securely so that no foreign objects, insects or small animals can get inside the control box. 6. Check that the cords do not get pulled, and then gently return the machine head to its original position. 2291B KE-430FX/KE-430FS, BE-438FX...
2292B (1) Ground wire from the machine head (Ground mark position) * The recommended tightening torque for the ground screws is 1.0±0.1 N・m. NOTE: Make sure that the ground connections are secure in order to ensure safety. KE-430FX/KE-430FS, BE-438FX...
4. INSTALLATION 4-11. Installing the rear cover (1) Rear cover (2) Screws [4 pcs] NOTE: Be careful not to clamp the cords when installing the rear cover (1). 3168B KE-430FX/KE-430FS, BE-438FX...
・ Use only the lubricating oil <Nippon Oil Corporation Sewing Lube 10N; VG10> specified by Brother. * If this type of lubricating oil is difficult to obtain, the recommended oil to use is <Exxon Mobil Essotex SM10; VG10>.
• Take care when tapping in the staples (3) to make sure that they do not pierce the cords. • Do not use extension cords, otherwise machine operation problems result. Control box Green and yellow wire (ground wire) 2353B KE-430FX/KE-430FS, BE-438FX...
Page 31
3. Use the six screws to tighten the cover of the control box. Check that none of the cords are being clamped by the cover at this time. Green and yellow wire (ground wire) KE-430FX/KE-430FS, BE-438FX...
Page 32
3. Use the six screws to tighten the cover of the control box. Check that none of the cords are being clamped by the cover at this time. Green and yellow wire (ground wire) 2351B KE-430FX/KE-430FS, BE-438FX...
After this, the program number will flash in the program No. display (6). 2. Depress the foot switch (7) to the 2nd step. The feed mechanism will move to the home position and the work clamp / button clamp will rise. 2339B 2nd step 2346B KE-430FX/KE-430FS, BE-438FX...
* When using threading mode for threading, the tension discs (1) will open so that the thread can be threaded more easily. (Refer to following page.) [When using the needle cooler (option)] [Two holes] Synthetic thread Spun rayon yarn [One hole] Approx. 40mm 3169B KE-430FX/KE-430FS, BE-438FX...
Page 35
THREAD/CLAMP indicator flashes 2389B Menu indicators switch off Threading the thread. Ending threading mode Press the THREAD/CLAMP key. • The work clamp/button clamp will return to where it was before threading mode was started. THREAD/CLAMP indicator switches off 2390B KE-430FX/KE-430FS, BE-438FX...
Loosen the nut (7) and move the bobbin winder tension assembly (8) up and down to adjust. * For case A, turn the bobbin winder tension assembly (8) clockwise (a), and for case B, turn it counterclockwise (b). Case A Case B 3173B KE-430FX/KE-430FS, BE-438FX...
Adjust the thread tension to the weakest possible tension by turning the thread tension nut (1) until the bobbin case will not drop by its own weight while the thread end coming out of the bobbin case is held. weaker stronger 2536Q KE-430FX/KE-430FS, BE-438FX...
Needle DP x 5 #14 DP x 5 #9 DP x 5 KN#11 DP x 17NY #19 DP x 17NY #12 *1: For KE-430FX and BE-438FX. *2: This is the tension value when the pretension is 0.05 N. KE-430FX/KE-430FS, BE-438FX...
5. PREPARATION BEFORE SEWING [Guide to maximum sewing speed for KE-430FX・FS] Max. sewing speed (sti/min) Standard hook Large hook 8 layers of denim 3,200 2,500 12 layers of denim 2,700 Ordinary materials 2,700 2,500 For knitted materials and 2,500 foundation garments NOTE: The thread may break due to heat under some sewing conditions.
Page 40
4487Q 5. With the KE-430FX, the lower thread may poke out from the underside of the material on the 2nd stitch for some types of material and thread. If this happens, it is recommended that you use sewing patterns that are designed for use with the thread nipper device.
1. Install the spring support (1) with the bolt (2). 2. Install the spring (3) with the washer (4) and the screw (5). * Adjust so that the spring (3) is in the middle of the button. 2308B KE-430FX/KE-430FS, BE-438FX...
Illuminates when the SELECT key (14) is pressed to switch to the X-scale setting. (10) Y-SCALE indicator Illuminates when the SELECT key (14) is pressed to switch to the Y-scale setting. (11) SPEED indicator Illuminates when the SELECT key (14) is pressed to switch to the sewing speed setting. KE-430FX/KE-430FS, BE-438FX...
Page 43
Shows the section number when you select a pattern in which the upper thread tension changes while the pattern is being sewn. (22) TENSION display <For KE-430FX and BE-438FX> Shows the upper thread tension value. (23) Setting keys [+, -] Used to change the value which is displayed in the SECTION No.
・ If the display is flashing, it means that no pattern number has been entered and applied. If you press the SELECT key or the TEST key, the changes to the program 2399B contents will be canceled. KE-430FX/KE-430FS, BE-438FX...
Page 45
Repeat steps 4 to 6 above to record the settings for each parameter. If you would like to continue setting another program, repeat steps 2 to 7 above. Exit program mode. Press the TEST key. ・The display will return to the normal display. 2404B TEST indicator switches off KE-430FX/KE-430FS, BE-438FX...
438FX: 200 sti/min to 2700 sti/min Setting units are 100 sti/min. (Initial value is 2000 sti/min.) * The setting is displayed in units of 10 sti/min. Sewing For a setting of 2000 sti/min, the display will be “200”.) speed Initial value 2408B KE-430FX/KE-430FS, BE-438FX...
Page 47
* The thread nipper device will not operate for settings other than Lo8 and Lo9. 0 - 300 (Initial setting is “75”.) * The later the value, the stronger the upper thread tension. Upper thread tension <For KE-430FX and BE-438FX> Initial value 2409B KE-430FX/KE-430FS, BE-438FX...
3 of “6-2. Program setting method”. 2413B 2414B Change the necessary parameters. Carry out the steps from step 4 onward in “6-2. Program setting method” to change the necessary parameters. KE-430FX/KE-430FS, BE-438FX...
6. USING THE OPERATION PANEL (BASIC OPERATIONS) 6-4. Checking the sewing pattern (KE-430FX・FS) Use test feed mode to check the needle movement with only the work clamp operating. Check that the needle hole does not come out from the frame of the work clamp.
TEST indicator flashes 2416B End test feeding. Press the TEST key. Depress the foot switch to the 1st step. The button clamp will be raised and preparation for sewing will be complete. 1st step TEST indicator switches off 2404B 4441Q KE-430FX/KE-430FS, BE-438FX...
6. USING THE OPERATION PANEL (BASIC OPERATIONS) 6-6. Correcting the upper thread tension <For KE-430FX and BE-438FX> The upper thread tension value is always displayed during sewing standby mode, and it can be changed at any time. <A. Basic method of use>...
6. Depress the foot switch to the 2nd step. The sewing machine will start sewing. 2384B 7. Once sewing is completed and the thread has been trimmed, the work clamp (2) / button clamp (3) will rise. 4116M KE-430FX/KE-430FS, BE-438FX...
・ The setting value (sti/min) will be displayed in the menu display (3). 2. Press the key (4) to set the sewing speed. (Sewing speed values: KE-430FX ・ FS: 200 to 3200; BE-438FX: 200 to 2700) 2451B <Changing slow start pattern>...