Tools Needed For Installation; Electrical Requirements - Whirlpool 27 Electric Built-in Combination Installation Instructions

Before
you
start...
Read Eleclriccrl and Carpenhy instructions.
Proper installation is your responsibility. A
qualified technician should install this oven.
Make sure You have everyMing necessary
for correct installation. lt Is the resgotibilitv of
the installer to comply with the in&all~on'
clearances specifed on the serial/ratina elate
The serial/rating plate is located dehing&e
Oven door on
the front frame.
Check
location where oven till be installed
Cabinel opening dimensions that are shown must be
used Given dimensions provide minimum clearance.
Contact surface must be solid and level.
The
recessed inslallaiion area
must provide complete
enclosure around me recess& portion of the oven.
AU OPENINGS 1~ THE WALL OR FLOOR WHERE OVEN
tS TO BE INSTALLED MUST BE SEALED.
Remove
all
packaging
material from microwave
oven cavity Check mlcrowave Oven area for
damage- see WARNING below. If any damage is
evident, do not ooerate until microwave oven is
The location should be away horn strong draft
area. such as windows. doors, and strong
Testing vents or fa M-S The oven should be
Notated for conver lient use in the Ltifchen.
checked by an duthorized service technician.
"Note: hrm In",,
Clearances specified are for
combusfible walls and malerials that
have a density of 20 or more pounds
per cubic 1001. No evaluation of
clearances has been made for
insfallalions adjacent fo malerials fhol
Elechicol ground
is required
See Electrical requirements.
Blocking lhe oven venl may touse
cabinet damage and mr baking
flush wilh the bottom of fhe cabinet
Tools needed for
installation:
Electrical
requirements
A
Thb appliance must be
. connected to
me
otooer
electrical voltage and f&&cy as
spechied on the serial/rating plate.
Models rated at 7.0 kxv on 240 volts (5.3
kw on x)8 v&s) or mbre require 0
separate 4O-ampere circuit. Models
rated at 3.6 hv on 240 vdts (2.7 kw on
208 volts) or les require a separate 30
ampere circuit Fuse both sides of me
line. A timedelay fuse or circuit
breaker ls recommended.
B ovm
MUST BE CONNECTED WITH
. COPPER WIRE ONLY.
Parts provided
for installation:
Personal Injury Hazard
* Do Nol aHerr@ lo operale Ihe
n+crowave oven wilh Ihe door open.
l
Do Nd tamper wilh or defeoi Ihe
safev inferlocks.
- Do Nd place objects between Ihe
ticrowave oven front face and
door.
- Do Nd allow soil or cleaner residue
lo accumulate on sealing surface of
the microwave oven door.
l
Do Nol operale the Wcrowave oven
il CkJrMged.
- Do Nof operate Ihe mfcrowove oven
5 door is bent
-hinges and latches are broken or
kxse.
- dca seals, sealing surfaces or
glass are broken.
The microwave oven door must close
properly lo provide safe operation.
- Only have a qualified repair person
adjust. repair and check microwave
oven for microwave leakage cn?er a
repair ts made.
- Do No! use microwave for
commercial purposes. The
mfcrowove oven In lhis unit is
designed for household use c+.
Failure 10 follow these instructions could
resutl In exposure lo excessive
microwave energy.
Elechicol Shock Hazard
* Electrical ground is required on this
appliance.
- Improper conneciion of the
equipmenl-grounding conductor
line
con resuil in a risk of elechicol
shock.
- Check with o quafiied electrician
il you ore in doubt as lo whether
Ihe appliance ir property
grounded.
- Do Nol hove a fuse in Ihe neulrol or
grounding circuit. A fuse in Ihe
neuirol or groundinq circuit could
resufl in el&hicof shock.
Failure lo follow these instructions
could result in o Bre, elecfrical shock
or other personal injury.
Save lnstollalion lnshucfions for
elechicaf inspeclofs use.
Elechical Shock Hazard
II is Ihe customer's responsibilii:
l
To contacl a quolired electrical
insloller.
- To assure that Ihe eleclrical
inslallallon is odequale and in
conformance wth Naiional Electrical
Code. ANWNFPA 70-lalesl edfiion.'
and all local codes and ordinances.
Failure to fdiow Ihere inshuctiis could
resuli in elechical shock.
Pencix~l Injury Hazard
* Securely fasten oven to cabinet
using Ihe hvo screws provided.
Failure lo do so could cause oven lo
mve or lip during use and resuli in
personal Injury. -
C
wire sizes and connections
. must conform to me
requirements of the National Electrical
Code ANSI/NFPA 70 - Ikrtest edition'
and all local codes and ordinances
for the kilowatt rating of the oven
This rating can be found on the
serial/rating plate located behind the
oven door on the front frame.
D
This appliance should be
n
connected dire& to the
fused disconnect (or circuit breaker)
through flexible, armored or non-
metallic sheathed. copper cable (with
Panel A