Mitsubishi Electric DPro930SB-BK Service Manual
  1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. Monitor
  5. Diamond Pro 930SB
  6. Service manual
Mitsubishi Electric DPro930SB-BK Service Manual

Mitsubishi Electric DPro930SB-BK Service Manual

Diamond pro 930sb
Hide thumbs
Table of Contents

Advertisement

Quick Links

PART NO. 599910624

SERVICE MANUAL

Diamond Pro 930SB
COLOR MONITOR
MODELS DPro930SB -BK(A)/(B)/-BK(B)
NEC-MITSUBISHI ELECTRIC VISUAL SYSTEMS CORPORATION
OCTOBER 2002
200307
08M530A3
08M540B3
08M530B3

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi Electric DPro930SB-BK

Summary of Contents for Mitsubishi Electric DPro930SB-BK

  • Page 1: Service Manual

    PART NO. 599910624 SERVICE MANUAL Diamond Pro 930SB COLOR MONITOR MODELS DPro930SB -BK(A)/(B)/-BK(B) NEC-MITSUBISHI ELECTRIC VISUAL SYSTEMS CORPORATION OCTOBER 2002 200307 08M530A3 08M540B3 08M530B3...
  • Page 2 WARNING The SERVICE PERSONNEL should have the appropriate technical training, knowledge and experience necessary to: • Be familiar with specialized test equipment, and • Be careful to follow all safety procedures associated with high voltage CRT circuit designs to minimize danger to themselves and their coworkers. To avoid electrical shocks, this equipment should be used with an appropriate power code and be connected only to a properly grounded AC outlet.
  • Page 3 PRODUCT SAFETY CAUTION 1. When parts replacement is required for servicing, always use the manufacturer's specified replacement. 2. Comply with all caution and safety-related notes on the product display chassis and picture tube. 3. When replacing the component, always be certain that all the components are put back in the place. 4.
  • Page 4 CONTENTS Page No. USER'S MANUAL ------------------------------------------------------------------------------- SERIAL NUMBER INFORMATION ---------------------------------------------------------- DISASSEMBLY ----------------------------------------------------------------------------------- ADJUSTMENT PROCEDURES -------------------------------------------------------------- INSPECTION -------------------------------------------------------------------------------------- TROUBLE SHOOTING ------------------------------------------------------------------------- CIRCUIT DESCRIPTION ----------------------------------------------------------------------- REPLACEMENT PARTS LIST --------------------------------------------------------------- BLOCK DIAGRAMS ---------------------------------------------------------------------------- SCHEMATIC DIAGRAMS --------------------------------------------------------------------- 10-1 PACKING SPECIFICATION ------------------------------------------------------------------- 11-1...
  • Page 5 User's Manual 1. A Version USER’S MANUAL 19 " Diamond Pro 930 18" Viewable Image Size www.mitsubishidisplay.com...
  • Page 6 Index Warning ..................1 Contents ..................2 Quick Start ................... 3 Controls ..................5 Recommended Use ..............8 Specifications ................10 Features ..................11 Troubleshooting ................. 13 References ................15 Limited Warranty ................ 16 TCO’95 ..................17 Avertissement ................20 Contenu ..................
  • Page 7 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
  • Page 8 Contents Your new Diamond Pro 930 monitor box* should contain the following: • Diamond Pro 930 Monitor with tilt/swivel base • Power Cord • Captive Signal Cable • User’s Manual Captive Signal Cable Power Cord User’s Manual * Remember to save your original box and packing material to transport or ship the monitor.

  • Page 9: Quick Start

    Quick Start To attach the Diamond Pro monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual. 3.
  • Page 10 Quick Start –continued Power Cord Figure C.1 Power Button Power Indicator Figure D.1...
  • Page 11 Controls (On-Screen Display) control buttons on the front of the monitor function ™ as follows: Main Menu Sub-Menu EXIT Exits the OSD menu. Exits to the OSD controls main menu. NOTE: Deactivates the OSD menu and activates the OSD menu when the OSD is turned off. CONTROL Moves the highlighted Moves the highlighted area...

  • Page 12: Geometry Controls

    Controls –continued Color Control/AccuColor ® Control System Color presets 1 through 5 selects the desired color setting. The bar is replaced by the color setting choice from 1, 2, 3, sRGB, 5. Each color setting is adjusted at the factory to the stated Kelvin degrees.
  • Page 13 Controls –continued Control: Eliminates picture impurities that may result from the GlobalSync ® earth’s magnetic field. While in the sub-menus (TL: Top Left, TR: Top Right, BL: Bottom Left, or BR: Bottom Right) use the –/+ control buttons to fine tune the GlobalSync corrections.

  • Page 14: Recommended Use

    Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE DIAMOND PRO COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.
  • Page 15 Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.

  • Page 16: Specifications

    Specifications Monitor Diamond Pro 930 Notes Specifications Monitor Diagonal: 19 inch 90° deflection, 0.24 mm grille pitch, Picture Tube Viewable Image Size: 18 inch medium short persistence phosphor, Radius: 50,000 mm aperture grille CRT, multi-layered, anti-static screen coating, dark-tint screen and OptiClear screen.
  • Page 17 Features SuperBright Diamondtron CRT: This patented flat aperture grille CRT delivers ® an exceptional viewing experience with unprecedented brightness and contrast and a virtually flat image that reduces distortion and glare so that what you see on-screen is what you get on your printed output. The state-of-the-art Mitsubishi U-NX electron gun and tight 0.24mm grille pitch delivers precise focus for crisp, clear text and images.
  • Page 18 Features –continued Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the resolution required. FullScan™ Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. GlobalSync /Corner Purity Control: Allows you to easily adjust impurities in the ®...

  • Page 19: Troubleshooting

    Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable •...
  • Page 20 Troubleshooting –continued Attention message displayed • Check the inputted signal. NOTE:The attention message may display when power on the Diamond Pro monitor. In case that the attention message disappear after in a little while, there is no problem at the inputted signal. Self check function •...
  • Page 21 References NEC-Mitsubishi Monitor Customer Service & Support Customer Service and Technical Support (800) 632-4662 (801) 907-3939 Parts and Accessories/Macintosh Cable Adapter: (888) NEC-MITS [888-632-6487] Customer Service Policies & Processes: http://www.necmitsubishi.com/ css/ServicePolicies/ServicePolicies.htm Online Technical Support Knowledge Base: http://www.necmitsubishi.com/ css/knowledgebase.cfm Customer Service & Technical Support Email: http://www.necmitsubishi.com/ css/techform.htm Sales and Product Information Sales Information Line...

  • Page 22: Limited Warranty

    Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase.

  • Page 23: Why Do We Have Environmentally Labelled Computers

    TCO’95 Diamond Pro 930 Black Model Congratulations! You have just purchased a TCO’95 approved and labeled product! Your choice has provided you with a product devel- oped for professional use. Your purchase has also contributed to reducing the burden on the environment and also, to the further development of environmentally adapted electronics products.
  • Page 24 TCO’95 –continued toxins, PCBs, which are suspected to give rise to similar harm, including reproductive damage in fisheating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur.

  • Page 25: Declaration Of Conformity

    Mitsubishi Diamond Pro 930 PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC-Mitsubishi Electronics Display of America and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others.
  • Page 26 2. B Version User’s Manual Diamond Pro 930 Diamond Pro 930 Diamond Pro 930 Diamond Pro 930 Diamond Pro 930 www.nec-mitsubishi.com 1-22...

  • Page 27: Declaration Of The Manufacturer

    Council Directive 73/23/EEC: – EN 60950 Council Directive 89/336/EEC: EN 55022 – EN 61000-3-2 – EN 61000-3-3 – EN 55024 and marked with NEC-Mitsubishi Electric Visual Systems Corporation 686-1, Nishioi Oi-Machi Ashigarakami-gun Kanagawa 258-8533, Japan Product NERGY As an E Partner, NEC-Mitsubishi Electronics Display of America, Inc.
  • Page 28 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. EFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
  • Page 29 Contents Your new Diamond Pro 930 monitor box* should contain the following: • Diamond Pro 930 Monitor with tilt/swivel base • Power Cord • Captive Signal Cable • User’s Manual • Sales Office List • CD ROM with Setup Software, complete User’s Manual and other helpful files. To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.
  • Page 30 Quick Start To attach the Diamond Pro 930 monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual.
  • Page 31 Quick Start – continued Power Outlet Power Cord Figure C.1 Power Button Figure D.1 6 User’s Manual 1-27...
  • Page 32 Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM press any of the control buttons ( EXIT, , –, +). s t i s t i i t c i t c .

  • Page 33: Size And Position Controls

    Controls – continued Size and Position Controls Left/Right: Moves the image horizontally (left or right). Down/Up: Moves the image vertically (up or down). Narrow/Wide: Decreases or increases the horizontal size of the image. Short/Tall: Decreases or increases the vertical size of the image. Color Control System Colour presets selects the desired colour setting.
  • Page 34 Controls – continued GlobalSync Control: Eliminates picture impurities that may result from the earth’s magnetic field. While in the sub-menus (GLOBALSYNC, TOP LEFT, TOP RIGHT, BOTTOM LEFT or BOTTOM RIGHT), use the –/+ control buttons to fine tune the GlobalSync corrections. NOTE: Mitsubishi recommends that you perform GlobalSync correction while running a typical application such as a spreadsheet or text document.
  • Page 35 Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE DIAMOND PRO 930 COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
  • Page 36 Recommended Use – continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
  • Page 37 Specifications : l a ° 0 e l f e l l c t i e l l - i t l - i t c i t t n i i t i i t a c i t i t i i t a i t i...
  • Page 38 Features SuperBright Diamondtron CRT: This patented flat aperture grille CRT delivers an exceptional viewing experi- ence with unprecedented brightness and contrast and a virtually flat image that reduces distortion and glare so that what you see on-screen is what you get on your printed output. The state-of-the-art Mitsubishi U-NX-DBF electron gun and tight 0.24 mm grille pitch delivers precise focus for crisp, clear text and images.
  • Page 39 Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable •...

  • Page 40: Environmental Requirements

    TCO’99 Diamond Pro 930 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further develop- ment of environmentally adapted electronics products.
  • Page 41 TCO’99 – continued TCO’99 demand requires that plastic components weighing more than 25 grams must not contain flame retar- dants with organically bound chlorine and bromine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Lead** Lead can be found in picture tubes, display screens, solders and capacitors.
  • Page 42 Diamond Pro 930 1-38...

  • Page 43: Serial Number Information

    Serial Number Information Refer to the serial number information shown below. EX.) SERIAL NUMBER LABEL Model : DPro930SB : DPro930SB-BK SERIAL NO. : g g g g g g g g g Manufactured Year : Last digit (ex. 2 → 2002)
  • Page 44 DISASSEMBLY • Before you disassemble the set, turn off power and pull out the power plug. • Use the appropriate screwdriver that fits the screw. If you use screwdriver that does not fit, you may break the screws. • Assembly is the opposite process of Disassembly. •...
  • Page 45 1. Remove the two screws (PL-CPTS*4*16*15BF) and unlock the two hooks. Hook Screws (PL-CPTS*4*16*15BF) 2. Hooks are removed by considering the penetration hole (three places) of the front upper part of Back Cover as a mark, inserting a jig from the direction of an end. and pushing in a jig downward. 3.
  • Page 46 Plate Shielding Assy 1. Remove the eleven screws (PL-CPTS*3*8*15BF). Screw (PL-CPTS*3*8*15BF) Screw (PL-CPTS*3*8*15BF)
  • Page 47 CRT BOARD 1. Remove the nine terminals and desolder the five points as shown. Terminals Solder 2. Disconnect the connectors “S201”, “S202”, “S203”, ”S204”, “S205” and “GND”. 3. Desoldor the wires “White wire”, “Red wire” and “G2”. S205 S203 S204 White wire Red wire S201...
  • Page 48 MAIN BOARD 1. Disconnect the connectors “S601”, “S602”, “S603”, ”S101” and “GND”. 2. Remove the screw (P-#2CRBITS*4*8*15BF) and two screws (PL-CPIMS*4*10*15BF). S603 S602 S701 S101 S601 Screw Screw (P-#2CRBITS*4*8*15BF) (PL-CPIMS*4*10*15BF) 3. Disconnect the connectors “S301” and “S401”. 4. Remove the screw (P-#2CRBITS*4*8*15BF). 5.
  • Page 49 7. Remove the four screws (PL-CPTS*4*16*15BF) and remove the Chassis Base from Cabinet Front ASSY. Screws (PL-CPTS*4*16*15BF) 8. Remove the six screws (PL-CPTS*3*8*15BF) and two screws (PL-CPIMS*3*10*15BF). 9. Remove the Main Board from Chassis Base. Screw (PL-CPTS*3*8*15BF) Screw (PL-CPIMS*3*10*15BF)

  • Page 50: Table Of Contents

    ADJUSTMENT PROCEDURES TABLE OF CONTENTS Page 1. Adjustment & Inspection Tools ..................4-2 2. Timing Table ........................4-2 3. Normal Condition Definition ..................... 4-2 4. Hot Key Operation ......................4-3 5. B+ Check ......................... 4-5 6. X-RAY Test ........................4-5 7.

  • Page 51: Adjustment & Inspection Tools

    1. Adjustment & Inspection Tools (A) Color Analyzer (B) Signal Generator CHROMA 2235 or compatible (C) Multi Meter (D) Hi-Voltage Probe (E) Convergence Meter (F) Degaussing Probe (G) Power Meter (H) CRT Landing Meter (I) External degaussing signal generator 2. Timing Table (Factory Mode –17 Modes) MODE RESOLUTION H-SYNC FREQ.

  • Page 52: Hot Key Operation

    4. Hot Key Operation (A) Factory Mode and Self test pattern : power on + ‘+’ key + ‘−‘ key. (B) Diagnosis Mode: no sync power on + “Select” key. (C) Exit Self test pattern: Power on + “Exit” key. (D) Factory Menu TAB 1) BRIGHTNESS / CONTRAST : Brightness...
  • Page 53 TAB 5) TOOLS 1 :Moire canceller :Linearity(VER.) :Linearity balance :Convergence(HOR.) :Convergence(VER.) : Global Sync (Top Left) : Global Sync(Top Right) : Global Sync(Bottom Left) : Global Sync(Bottom Right) * Global Sync : Corner purity TAB 6) TOOLS 2 TOOL 2 is as same as user mode TAB 7) INFORMATION DS :Destination TAB 8) Purity...

  • Page 54: B+ Check

    5. B+ Check (A) Mode: No.1 (B) Pattern: All Black. (Brightness set to cut off) (C) Adjust VR101 to make 13.9V of D153 cathode voltage. (D) Check power source should be 79.5V ±1V, 6.9V ±0.2V, 26.5V ±1V, -14.1V ±0.5V, 13.9V ±0.1V. (E) After aging, Check 13.9V±0.1V of D153 cathode again.

  • Page 55: White Balance Adjustment

    (G) Change Mode to No.1, Check V size to do about 10mm over scan with keeping V size=100%, If size is not enough, Re-adjust VG to 5~10mm over scan with keeping v size=100%. 10. G2 Initial Setting (A) Mode No. 11 (B) Pattern: Full Black (C) Adjust screen VR to make G2 voltage 650V ±10V.
  • Page 56 2. 5000K (Select color Mode 5000K) 1) Brightness set to 50% and Contrast to maximum. 2) Set pattern to 50*50mm white block Pattern. 3) Adjust 2 channel gain control to x=0.345 ±0.005, y=0.359 ±0.005 and keep one channel with 100%. 4) Adjust R, G, B gain to meet following spec.

  • Page 57: Focus Adjustment

    12. Focus Adjustment (A) Mode: No.11, 9300K (B) Pattern: Green Crosshatch, Brightness just cut off, Contrast maximum. (C) Adjust V- Parabola Vp-p by OSM V-Focus control in Factory Mode. V focus: 60% of control bar. (D) Check T302 output Vp-p. H-para(R330)=470Vp-p ±30V, V-para=130 ±10V. H-para=470V ±30V V-para=130V ±10V Horizontal...

  • Page 58: Convergence Adjustment

    14. Convergence Adjustment (A) Receive signal 11 (B) Pattern: Cross hatch. (C) Adjust H-CONVERGENCE, V-CONVERGENCE by OSM in Factory Mode to both around 50%. (D) Use the convergence meter to check whether within the spec. If it cannot be within the spec, adjust Yoke coil and VR to make be follow the spec.
  • Page 59 6) Start at the same time both “DEGAUSS (+)” pushing and External degaussing signal generator running. 7) Uneven color is not observed by visual check. When uneven color observes, it should be rejected. 8) Set magnetic field to “Bh=-0.03mT”. 9) Start at the same time both “DEGAUSS (+)” pushing and External degaussing signal generator running.

  • Page 60: Distortion Adjustment

    17. Distortion Adjustment Factory mode setting * After completion of adjustment exit the factory mode and data will be saved. Signal: All signals Cross hatch Perform the adjust for signal No.13 in step 1 ~ 3. Perform the adjust for above all signal in step 4 ~ 5. 1.
  • Page 61 3. Parallelogram distortion Adjustment (1) Select the “ “ icon in OSM TAB 4. (2) Adjust “+”, “-“ SW so that the vertical line and horizontal line at the screen’s center fall at right angles. (less than 90 ±0.5 degree) 4.

  • Page 62: Setting Before Shipment

    18. Setting Before Shipment (A) Color Temp: 9300K (SB mode off). (B) OSM position: Center of the screen (C) Brightness: Preset (50%) (D) H Moire: Minimum (E) Refresh Notice: OFF (F) OSM turn off time: 45 sec (G) IPM off mode: Enable (H) Language: English for A,B,C,R Version, Japanese for J Version.

  • Page 63: Adjustment Magnetic Field

    19. Adjustment Magnetic Field Vertical: +40uT, Horizontal: ±0uT(Neutral) * Notes About Degaussing Method Follow the degaussing procedure as below. (To prevent intertwinement of aperture grille.) 1) Use stick type degaussing probe at demagnetizing CRT. Do not use ring type degaussing probe. 2) In order to remove a magnetization from front, top, bottom and side of CRT, and bottom chassis.

  • Page 64: Timing Sheet

    20. Timing Sheet Preset Mode No. VESA VESA VESA (MAC) 640*400 640*480 640*480 640*480 800*600 832*624 Signal Name (75) (85) (75) (75) 640*400 640*480 640*480 640*480 800*600 832*624 Resolution 25.175 25.175 31.500 36.000 49.500 57.283 Dot Clock (MHz 31.47 31.469 37.50 43.269 46.875...
  • Page 65 Preset Mode No. VESA VESA VESA VESA VESA VESA 800*600 1024*768 1024*768 1280*1024 1280*1024 1600*1200 Signal Name (85) (75) (85) (75) (85) (75) 800*600 1024*768 1024*768 1280*1024 1280*1024 1280*1024 Resolution 56.250 78.750 94.5 135.0 157.5 202.5 Dot Clock (MHz) 53.674 60.023 68.677 79.976...
  • Page 66 Preset Mode No. VESA VESA VESA 1600*1200 1792*1344 1920*1440 640*480 1152*870 Signal Name (85) (75) (60) (67) (75) 1600*1200 1792*1344 1920*1440 640*480 1152*870 Resolution 229.5 261.0 234.0 30.24 Dot Clock (MHz) 106.250 106.27 90.0 35.0 68.681 (kHz) 85.0 74.997 66.67 75.062 (Hz) 2160...
  • Page 67 INSPECTION TABLE OF CONTENTS Page 1.Scope --------------------------------------------------------------------------------------------------------------- 5-2 1.1 Introduction --------------------------------------------------------------------------------------------------- 5-2 1.2 General Description ---------------------------------------------------------------------------------------- 5-3 1.3 Regulations -------------------------------------------------------------------------------------------------- 5-4 1.4 Regulation Information & Marking Location ---------------------------------------------------------- 5-5 2. CRT Specifications ---------------------------------------------------------------------------------------------- 5-6 3. Electric Specifications ------------------------------------------------------------------------------------------ 5-7 3.1 Deflection Circuit -------------------------------------------------------------------------------------------- 5-7 3.2 Signal Input --------------------------------------------------------------------------------------------------- 5-7 3.3 Video Performance ----------------------------------------------------------------------------------------- 5-7 3.4 Power Supply ------------------------------------------------------------------------------------------------ 5-8...

  • Page 68: Scope

    The following list shows the model name, Cabinet color, Audio function and market. MODEL NAME Cabinet Audio MARKET Ver. color Base DPro930SB-BK(A) USA/Canada Aver. DPro930SB(B) DAS / LG Europe Bver. DPro930SB-BK(B) DAS / B Europe Bver.

  • Page 69: General Description

    1.2 General Description Item Spec. REMARKS Vendor / Model No. Mitsubishi / M46LVT62X41 Diamondtron U2 (Aperture Grille) Type Size 48cm / 45.7cm Diagnonal Viewable Image 1 CRT (19" / 18" Diagnonal Viewable Image) Grill Speacing Approx. 0.24mm (Phosphor Spacing) (Approx. 0.25mm) Aperture Grille Phosphor Type Face-plate...

  • Page 70: Regulations

    1.3 Regulations GEOGRAPHICAL REGULATIONS REGION SAFETY X-RAY ELF/VLF* Power Ergonomics Miscellaneo Management* And others DPro930SB-BK (A) FCC-B DHHS MPR-III Energy Star TUV-GS CE Marking C-UL DOC-B Red Act TCO’95 TCO’95 (IS9241-3 WHQL TUV/GS EN55022-B (Black) (Black) IS9241-7 (Win ME, EN55024...

  • Page 71: Regulation Information & Marking Location

    1.4 Regulation Information & Marking Location Marking Location Regulation Information A ver. B ver. UL1950 3rd Edition (or UL60950 3 edition) C-UL CAN/CSA-C22.2 NO.950:1995 (or CAN/CSA-C22.2 No.60950:2000) (1), (2) TUV-GS EN60950 : 1992 & AD1/AD2/AD3/AD4/AD11(or EN60950:2000), EK1-ITB 2000, ISO9241-3: 1992, ISO9241-7: 1998, ISO9241-8: 1997 (1),(2),(3) (1),(2),(3)

  • Page 72: Crt Specifications

    2. CRT Specifications Vendor Mitsubishi CRT Model No. M46LVT62X41 Type Diamondtron u2 (Aperture Grille) 48cm/45.7cm Diagonal View able Image Size (19”/18” Diagonal Viewable Image) Dot pitch 0.24mm Phosphor Spacing 0.25mm Deflection Angle 90 degree Phosphor Type Electron Gun Type U-NX-DBF type Light Transmission at Approx.43.0% (Include Face-plate coating) Center (Approx.)

  • Page 73: Electric Specifications

    3. Electric Specifications 3.1 Deflection Circuit Scanning Frequency 30 – 110 kHz ≥ 1.1 µsec Back Porch Horizontal ≥ 2.3 µsec Blanking ≥ 0.8 µsec H-sync Width Scanning frequency 50 – 160 Hz ≥ 420 µsec V-sync + V-back Porch Vertical 2H ≤...

  • Page 74: Power Supply

    3.4 Power Supply 100 - 240 VAC ± 10% Input Voltage 50/60Hz ± 3Hz Frequency Power Consumption (Max.) 100W 100 - 240VAC, 2.2A Condition (Monitor): Condition: Input voltage:100-240VAC Signal: No.14 (1600x1200 (85Hz), (All white)) Contrast: Max, Brightness: Max, SB Mode: ON (SB Mode 2) H/V size: full scan Others: Preset (Typical)

  • Page 75: Degaussing

    3.6 Degaussing Auto Degaussing The monitor has an automatic degaussing function which activates when the unit is turned on. Manual Degaussing This activates degaussing at the user’s discretion after the unit is operating The Monitor requires minimum of 15 minutes between manual degaussing operations. 4.

  • Page 76: Osm (On-Screen Manager) Function

    4.2 OSM (On-Screen Manager) Function 4.2.1 OSM Menu Tab 1 Tab 2 Tab 3 Tab 4 5-10...
  • Page 77 Tab 5 Tab 6 Tab 6 (Language) Tab 6 (OSM Position) Tab 6 (OSM Turn off) Tab 6 (OSM Lock) Tab 6 (IPM OFF Mode) 5-11...
  • Page 78 Tab 6 (Edge Lock) Tab 6 (Hot Key) Tab 6 Factory Preset Tab 7 (URL indication) Tab 7 (Display Mode) Tab 7 (Monitor info.) 5-12...
  • Page 79 Tab 7 (Refresh Notifier) Refresh Notifier Item Reset Tab Reset Factory Preset 5-13...
  • Page 80 Others 5-14...
  • Page 81 4.2.2 OSM Item Variability & Default Position. Item Default Item Push"+" Push"-" Reset Brightness 0-100% Down (Normal, SB mode2) Adjusted (SB mode1) Contrast 0-100% Aver :100% Down Bver :85% Degauss Operate Left/Right (H.Posi) 0-100% Adjusted Right Left Down/Up (V.Posi) 0-100% Adjusted Down Narrow/Wide (H.Size)
  • Page 82 URL indication WWW.NECMITSUBISHI.COM Display Mode FH : Horizontal Frequency & Polarity FV : Vertical Frequency & Polarity Monitor Info. Model Name & Serial Number Refresh Notifier OFF/ON Cursor move to +/- Default show factory shipping condition. 5-16...

  • Page 83: Back Panel

    4.3 Back Panel a: AC POWER CONNECTOR (3P IEC Plug) b: SIGNAL INPUT CONNECTOR captive type (D-SUB 15P) Signal Cable: Length:1800 ±50mm, Color: Hazegray (NEC#8508) 4.4 Connector Pin Assignment 1) Signal Input Connector (mini D-sub 15P captive cable) Signal Red-video Green-video Blue-video DDC Gnd...

  • Page 84: Ddc (Display Data Channel) Functions

    4.5 DDC (Display Data Channel) Functions VESA DDC 2B (EDID data only) VESA DDC/CI (Support 9pin-5V) 4.6 Preset Timing Factory-presets : 17 see Appendix 1 for detail timing parameters. (Signal No. 1 to No.17 are adjustment Signals.) User-presets : 10 Preset Timing Discrimination ≥...

  • Page 85: Display Quality

    5. Display Quality 5.1 Basic Test Conditions AC Voltage 120VAC 60Hz or 230VAC 50Hz No.13, 1280 x 1024 (85Hz) (fH=91.1kHz fV=85Hz) Video Signal Video signal 0.70 ±0.01Vp-p Picture Reverse cross hatch pattern Warm Up More than 30 min. with full white picture Temperature 20 –...

  • Page 86: Luminance (Brightness)

    5.3 Luminance (Brightness) Signal No.13 (VESA1280*1024@85Hz) 5.3.1 Luminance Contrast : Max. at CRT center Brightness : default position (Cut off) ≤ Full White ≤ 110 cd/m (Full white pattern) 90cd/m (at 9300K + 8 M.P.C.D.) 5.3.2 Luminance SB Mode : OFF at CRT center Contrast : Max.

  • Page 87: Color

    5.4 Color Signal No.13 (VESA1280*1024@85Hz) 5.4.1Color Temperature Color-1: 9300K + 8 M.P.C.D. (Window pattern) Xref=0.283 ± 0.015 (H:33%,V:33%) Yref=0.297 ± 0.015 Color-2: 8200K Contrast : 100cd/m X=0.290 ± 0.015 Brightness : Cut off Y=0.313 ± 0.015 Color-3: 7500K X=0.300 ± 0.015 Y=0.315 ±...

  • Page 88: Geometric Distortion

    5.5 Geometric Distortion 5.5.1 Partial Distortion The number of pole point each side All Preset Signals Pole point Top and Bottom side: Less than 3 point Left and right side: Less than 2point 5.5.2 Inner Distortion All Preset Signals With Crosshatch ≥...

  • Page 89: Linearity

    5.5.7. Parallelogram All Preset Signals α -0.8mm ≤ a ≤ +0.8mm or -0.2 degree ≤ α ≤ +0.2 degree 5.5.8 Overall Distortion All Preset Signals : d ≤ 1.5mm Bottom : b ≤ 1.5mm Left side : a ≤ 1.5mm Right side: c ≤...

  • Page 90: Misconvergence

    5.7 Misconvergence Zone A: X, Y ≤ 0.25 mm within the 266 mm diameter circle Misconvergence Zone B: X, Y ≤ 0.30 mm within 356 mm x 266 mm * With White Crosshatch (17 lines horizontally by 13 lines vertically ) applied. * Zone A is a circular area with 266mm diameter at the center.

  • Page 91: Focus

    5.8 Focus Focus Resolution: 1600 x 1280 (75Hz) Character: 7 x 9 pixel ”∃” Signal No.13 Color : White Contrast : Max. Judgment: Brightness: Cut off “∃” character are readable with clearly at the whole screen. 9 lines The gap between lines should be crisp.

  • Page 92: Halo

    5.9 Halo Halo Character: Crosshatch Signal No.13 Judgment: Contrast : Max. Each color (Red, Blue) line do not form halos. Brightness: Preset Vertical lines : halos + core are less than 7 grills(R), 7 grills(B) Horizontal lines : core : halos = 1 : less than 1.5 Horizontal Vertical Core...

  • Page 93: Raster Regulation

    5.11 Raster Regulation Judgment: Raster Size Regulation 1.The total horizontal and vertical size of the picture shall not change more than 1.0mm, when displaying a flat field, and All Preset Signals adjusting the brightness from 30 to 110 cd/m (Full White pattern) 2.

  • Page 94: Warm-Up Drift

    5.13 Warm-up Drift Warm-up drift Display pattern: Window pattern (H:33%,V:33%) Crosshatch (Back: White, Line: Black) Contrast : Max. Brightness: Preset Aging condition: Crosshatch (Back: White, Line: Black) Measure the luminance, the size, the position, the distortion and the color temperature after 30 second (data A) and 2 hours (data B) from turn on power supply.

  • Page 95: Crt Limits Of Screen And Faceplate Blemish

    6. CRT Limits of Screen and Faceplate Blemish 6.1 CRT Face Plate Defect 6.1.1 Inspection condition 1) Adjust each gun to provide approximately 34cd/m2 of 9300K+27M.P.C.D. (or 6550K+727M.P.C.D.) light at the center of the screen. Ambient light level at the tube face should be approximately 10 luxes. 2) When the tube is not operating, the screen should be viewed under high-level source incandescent light of approximately 200 luxes measured at he faceplate surface.

  • Page 96: Ar-Film Blemishes

    2) Face Plate Defect a. Blisters, opaque spots and elongated closed blisters Average diameter (*1) Allowable number (pcs) Minimum Separation (mm) (mm) Zone A Zone B Total 0.76 0.51 ~ 0.75 0.26 ~ 0.50 (*2) 0.11 ~ 0.25 Note (*1) Average diameter is smaller one of the following two expressions. (a+b)/2 or a/20+2b (a: length, b: width) Note (*2) Less than 5pcs.
  • Page 97 6.2.2 Quality Zone The screen is divided into following 3 zones. Zone A: Inside of the central rectangle of horizontal 360mm by 270mm on the screen. Zone B: The area between outside the rectangle and the edge of the phosphor screen. Zone C: The area outside the edge of the phosphor screen.
  • Page 98 Standards Average diameter classified by a contrast (Note 1) (mm) Allowable number Allowable Length (mm) High contrast Middle contrast Low contrast Zone A Zone B ~ 0.10 ~ 0.20 ~ 0.50 Ignore Ignore 0.11 ~ 0.25 0.21 ~ 0.50 0.51 ~ 1.25 2 [4] 4 [5] 0.26 ~ 0.50...

  • Page 99: Inspection Of Plug & Play Communication And Osm "Monitor Information" For Model Name/ Serial Number

    7. Inspection of PLUG & PLAY Communication and OSM "MONITOR INFORMATION" for Model Name/ Serial Number 7.1 System Connection This system should be connected as shown below. Program Disk Part No.599910508 Part No. 599910609 Signal Cable DESKTOP/NOTE Printer Cable EDID JIG (NPG) Signal Generator Monitor...
  • Page 100 g. Check the serial number of the set and enter an input of the following code from the keyboard. 08M530A3 Serial Number (Model Code + 1 Space + Serial No.) Example: 08M530A3 2900001YA h. Press the Enter key. Then, the EDID data, OSM model name, and the serial number begin to be written in.

  • Page 101: Error Messages

    7.5 Error Messages • IIC Communication Error Communication disabled • EDID Check Sum Error Entry of false EDID • DDC2 Does Not Find Head Data DDC2 Communication disabled 7.6 EDID Data File The EDID data file text is shown below. When you write or inspect EDID for this monitor, the following table can be used.

  • Page 102: Appendix 1 Preset Timing Chart

    Appendix 1 Preset Timing Chart [ H-SYNC ] [ VIDEO ] [ V-SYNC ] [ VIDEO ] Preset Signal Separate Clock Signal Name (uSec) (uSec) (uSec) (uSec) (uSec) (mSec) (mSec) (mSec) (mSec) (mSec) (MHz) (kHz) (Hz) Composite (dot) (dot) (dot) (dot) (dot) (line)
  • Page 103 TROUBLE SHOOTING TABLE OF CONTENTS Refer to User’s Manual trouble shooting section before using this chart. Page 1. NO OPERATION, POWER LED FLASHING ..............6-2 2. NO OPERATION, POWER LED OFF ................6-3 3. VIDEO NOISE, NO SYNC ..................... 6-4 4.

  • Page 104: No Operation, Power Led Flashing

    1. NO OPERATION, POWER LED FLASHING POWER LED FLASHING POWER SW TURN OFF MULTIMETER TEST Q314, Q504, D505, D151, D152, D153, D154, D155 1. DC P/S O/P VOLTAGE SET AT 12V,CURRENT SET AT 600MA. POSITIVE CONNECT TO C501”+”. NEGATIVE CONNECT TO U501 Pin 7. 2.

  • Page 105: No Operation, Power Led Off

    2. NO OPERATION, POWER LED OFF POWER SW TURN OFF CHECK F101 CHECK CHECK CHECK Q314, Q504 Q3305 Q101, Q102, R121 1. DC P/S O/P VOLTAGE SET AT 17V,CURRENT SET AT 200MA. POSITIVE CONNECT TO C111”+”. NEGATIVE CONNECT TO C107”-“. SCOPE SET AT 10V/DIV, 10US/DIV, PROBE CHECK CONNECT TO Q101-GATE AND C107”-“.

  • Page 106: Video Noise, No Sync

    3. VIDEO NOISE, NO SYNC CHECK Q101 G-S FREQUENCY CHECK HORIZONTAL CHECK D116, D115 SYNCRONIZE FREQUENCY L501 SYNC “+” R108, R118 WITH H-SYNC TO GND, D116 TO GND CHECK TROUBLE IN U501 U501 G-S FREQUENCY 1, 15 PIN CHECK U701 TROUBLE IN U701 39, 33 PIN NORMAL OPERATION...

  • Page 107: No Video

    4. NO VIDEO NO VIDEO CHECK REFER TO SCREEN CONTROL “NO RASTER” CLOCKWISE ON PAGE CHECK TROUBLE IN U201 PINS 5, 6, 7 R/G/B SIGNAL, SIGNAL LEVEL SIGNAL CABLE S202 CHECK PROBLEM IN U201 U201 PINS 18, 19, 20 CLAMP (PIN 23) SIGNAL LEVEL U201 12V VOLTAGE CHECK...
  • Page 108 Continue CHECK PROBLEM IN HETER VOLTAGE Q155, Q156, U701 CHECK PROBLEM IN G1=-11V Q307, U501, U701 VOLTAGE PROBLEM IN CRT...

  • Page 109: No Raster

    5. NO RASTER NO RASTER POWER SUPPLY CHECK CHECK CHECK PROBLEM IN U501 PINS 14, 15 MCU U701 H/V SYNC CHECK U701 PIN 35, PIN 2 IS TROUBLE CHECK CHECK ISCL, ISDC U501 PINS 6, 8 IN U501 BDRY, HDRY CHECK TROUBLE IN Q504 DRAIN ABOUT...
  • Page 110 Continue CHECK TROUBLE IN B301 EMITTER H-BLKD C331, D316, C332 PULSE 40Vp-p CHECK CHECK TROUBLE IN Q305 DRAIN PULSE FBT 2PIN Q309, R301, D151 280Vp-p TROUBLE IN U301, Q303, Q305, Q304 CHECK TROUBLE IN G1 VOLTAGE ABOUT Q307, ZD303, T301 -20 ~ -5V TROUBLE IN G2 VOLTAGE T301...

  • Page 111: Sync Trouble

    6. H. V. SYNC TROUBLE TROUBLE WITH HOR OR VER SYNC CHECK CONNECTOR S701 TROUBLE IN (PINS 1, 2), SIGNAL SIGNAL CABLE CHECK TROUBLE IN U701 (PINS 39,40) H/V SYNC LINE & H/V SYNC Q701, Q702 SIGNAL CHECK CHECK TROUBLE IN U701 (PINS 32,33) U701 (PIN 5) 5V LINE...

  • Page 112: Poor Focus

    7. POOR FOCUS POOR FOCUS CHECK T301 12PIN H-DYNAMIC ADJUST PARBOLA WAVEFORM 470Vp-p T301 STATIC FOCUS VR AND V-DYNAMIC PARABOLA DYNAMIC FOCUS VR WAVEFORM 130Vp-p 1. CHECK STATIC FOCUS AND DYNAMIC FOCUS VR LINE TO CRT SOCKET. 2. CRT SOCKET OR CRT POOR. CHECK T302 H AND V TROUBLE IN...

  • Page 113: Poor Horizontal Linearity

    8. POOR HORIZONTAL LINEARITY POOR HORIZONTAL LINEARITY CHECK ADJUST VR501 H. CENTERRING TROUBLE IN Q505, R531, D507 TROUBLE IN T303, Q325, Q326, Q315, Q317, Q319, Q321, Q322, U701 6-11...

  • Page 114: Rotation Problem

    9. ROTATION PROBLEM TROUBLE IN ROTATION 14VSW NO 7V NO CHECK S601 CHECK TROUBLE IN Q151 WIRE TO DY 14VSW, 7V TROUBLE IN TROUBLE IN Q155 Q327, Q328, U302, U701 6-12...

  • Page 115: Cg Problem

    10. CG PROBLEM TROUBLE IN 14VSW NO 7V NO CHECK S602 CHECK TROUBLE IN Q151 WIRE TO DY 14VSW, 7V TROUBLE IN TROUBLE IN Q155 Q455, Q461, Q456, Q462, U403, U701 6-13...

  • Page 116: Purity Problem

    11. PURITY PROBLEM PURITY NG CHECK PARAMETER CHECK S603, S604, S204 TROUBLE IN CHECK ZD401, R457 14VSW, 14VSW LINE -14VSW 12V -14VSW LINE CHECK TROUBLE IN U202 U202, U701 PINS 9,10,11,12 CHECK TROUBLE IN U402, U404 U402, U404, U702 TROUBLE IN COIL W DEGAUSS PARAMETER C-TIME-TL...

  • Page 117: Self Diagnosis Function

    12. SELF DIAGNOSIS FUNCTION This monitor has SELF DIAGNOSIS function as below table, when turn on monitor, please check LED blink times. 12.1 X-ray Protector Operate On this condition, please check around T301 (FBT). U701 detect pin 3. Normally this pin is low level. When operate X-ray circuit, U701 pin 3 become high level.
  • Page 118 CIRCUIT DESCRIPTION TABLE OF CONTENTS Page 1. Power Supply Circuit ......................7-2 1.1 Outline ..........................7-2 1.2 Harmonics .......................... 7-2 1.3 EMI ............................. 7-2 1.4 AC Rectifier and Smoothing Capacitor ................7-2 1.5 Degaussing circuit ......................7-2 1.6 Transformer and energy induction ...................

  • Page 119: Power Supply Circuit

    1. Power Supply Circuit 1.1 Outline This power supply unit adopts the switching mode technology, and is an off-line mode type unit that provided several different DC outputs. The scanning frequency is available in different values ranging from 31 kHz to 110 kHz.
  • Page 120 2) The power supply MOS FET Q101 carries out the ON/OFF operation of the control unit, by means of U101 KA3842A. KA3842A is a PWM (pulse width modulation) IC chip, with 16 V starting voltage and 10 V cut-off voltage. The following list shows the pin layout of KA3842A pulse width modulation IC chip.

  • Page 121: Power Saving

    1.7 Power saving Suspend mode : Every DC voltage operation of the CRT is reduce to 2 Volt. OFF mode : The color of the power LED101 switches from green to orange. 1) When the power switch is turned ON when there is nothing being entered in the video cable. At that time, if the video is shifted from the free-run mode to the suspend mode, the transistor Q151 turns OFF and the operation returns to the OFF mode within a few seconds.

  • Page 122: Video Circuit & Osd

    2. Video Circuit & OSD The video amplifier system is consist of the Pre-Amplifier, the Video-Power-Amplifier, and the cutoff-Voltage circuit. a) The U201 (LM1267) is a three channel video pre-amplifier IC, that controlled by MCU IIC bus for the features of contrast, output DC level, 3 SUB gain controls (R-Gain, G-Gain, B-Gain). b) U201 PIN 23 need a positive pulse for clamping and PIN 24 also need a positive pulse for blanking.

  • Page 123: Horizontal Deflection

    5. Horizontal Deflection a) U501 is a horizontal signal processing IC. Horizontal Driver signal is output from pin 8 of U501 TDA4856 and through Q506, Q507 to drive Q313 and T304. b) T304 is an on/off type driver transformer. It functions to convert primary energy to secondary, and drive the horizontal output transistor Q314.

  • Page 124: Dynamic Focus

    7. Dynamic Focus a) H-Focus: T302 is H-Dynamic Focus amplified. b) V-Focus: U501 pin 32 output waveform through R356 and C343 to get a parabolic waveform. This waveform is amplified by Q312 and input into T302. c) H-Focus and V-Focus are into T302 to get a combined waveform that will input to FBT. 8.
  • Page 125 REPLACEMENT PARTS LIST(For U.S.) The components specified for Model Dpro930SB-BK(A) SYMBOL Part No for NPG DESCRIPTION *** ICS *** U101 DD002600 IC LINEAR KA3842A 8P U201 80016621 IC LM1267 U202 EH110051 IC MTV030N-46 20PIN U203 80010891 IC LM2480 U204 EH110071...
  • Page 126 Part No for NPG SYMBOL DESCRIPTION Q313 EF206301 FET N YTAF630 TO-220F Q314 80008151 TR NPN 2SC5587 TO-3P Q315 EF206301 FET N YTAF630 TO-220F Q316 80014321 TR NPN KRC102M TO-92(T) Q317 80003311 FET N YTAF640 TO-220F Q318 80014321 TR NPN KRC102M TO-92(T) Q319 80003311 FET N YTAF640 TO-220F...
  • Page 127 Part No for NPG SYMBOL DESCRIPTION D112 EJ044148 DIODE T" 1N4148" D113 EJ044148 DIODE T" 1N4148" D115 EJ044148 DIODE T" 1N4148" D116 EJ044148 DIODE T" 1N4148" D117 EJ044148 DIODE T" 1N4148" D118 80003821 DIODE 1A/1KV UF4007 D041 D120 EJ044148 DIODE T" 1N4148" D131 EJAC0010 DIODE/T 1A 1N4007...
  • Page 128 Part No for NPG SYMBOL DESCRIPTION D317 EJB00004 DIODE/A 5TUZ47 D318 80003821 DIODE 1A/1KV UF4007 D041 D319 EJ044148 DIODE T" 1N4148" D320 EJA00018 DIODE/T 1A UF4006 D321 80003841 DIODE 1A/20V UF4003 DG41 D322 80009741 DIODE/T UF4005 D323 EJA00018 DIODE/T 1A UF4006 D401 EJB00017 DIODE/A 1A IN4936...
  • Page 129 Part No for NPG SYMBOL DESCRIPTION T302 HE300011 TRANS DF X'FM EI-22 N2901 T304 HE200011 TRANS HDDRIVE X'FM EI-19 *** VARIABLE RESISTORS *** VR101 FF300501 VR CARBON 6MM 500H/B VR301 FF310223 VR CARBON 6MM 22K VR302 FF310223 VR CARBON 6MM 22K VR501 FF310502 VR CARBON 6MM 5K...
  • Page 130 Part No for NPG SYMBOL DESCRIPTION L250 HB013228 PEAKING COIL/T 0.22UH K L251 HB013188 PEAKING COIL/T 0.18UH K L301 80016071 CHOCK COIL 14UH P75 L501 80016081 CHOCK COIL 8.0MH (DRWW16* RL181 80003761 REPLY 12V 6P OSA-SS-212DM T303 HA300011 L LINER N2901 T501 80016801 CHOKE COIL 45UH N1901...
  • Page 131 Part No for NPG SYMBOL DESCRIPTION R107 FB240010 METAL 1/4W(T) 1% 1OHM R108 FA040100 CARBON 1/8W(T) 5% 10OHM R109 FA240470 CARBON 1/4W 5% 47OHM R110 FA240103 CARBON 1/4W(T) 5% 10K R111 FA240103 CARBON 1/4W(T) 5% 10K R112 FA240563 CARBON 1/4W(T) 5% 56K R113 FA240242 CARBON 1/4W(T) 5% 2.4K...
  • Page 132 Part No for NPG SYMBOL DESCRIPTION R203 FA040332 CARBON 1/8W(T) 5% 3.3K R204 FA040472 CARBON 1/8W(T) 5% 4.7K R205 FA040101 CARBON 1/8W(T) 5% 100OHM R206 FA040102 CARBON 1/8W(T) 5% 1K R207 FA040101 CARBON 1/8W(T) 5% 100OHM R208 FA040101 CARBON 1/8W(T) 5% 100OHM R209 FA040101 CARBON 1/8W(T) 5% 100OHM...
  • Page 133 Part No for NPG SYMBOL DESCRIPTION R286 FA040123 CARBON 1/8W(T) 5% 12K R287 FA040102 CARBON 1/8W(T) 5% 1K R288 FA040102 CARBON 1/8W(T) 5% 1K R289 FA040103 CARBON 1/8W(T) 5% 10K R293 FA040102 CARBON 1/8W(T) 5% 1K R294 FA040102 CARBON 1/8W(T) 5% 1K R295 FA040103 CARBON 1/8W(T) 5% 10K...
  • Page 134 Part No for NPG SYMBOL DESCRIPTION R347 FA360270 CARBON 1/2W/M(T) 5% 27H R348 FK010010 R MOF 5W 1.2J (AI) R349 FB241003 METAL 1/4W(T) 1% 100K R350 FA040562 CARBON 1/8W(T) 5% 5.6K R351 FA040103 CARBON 1/8W(T) 5% 10K R352 FA040103 CARBON 1/8W(T) 5% 10K R353 FA040103 CARBON 1/8W(T) 5% 10K...
  • Page 135 Part No for NPG SYMBOL DESCRIPTION R410 FB271801 METAL 1/4W/M(T) 1% 1.8K F R411 FA240222 CARBON 1/4W(T) 5% 2.2K R412 FA040103 CARBON 1/8W(T) 5% 10K R413 FA040472 CARBON 1/8W(T) 5% 4.7K R414 FA040332 CARBON 1/8W(T) 5% 3.3K R415 FA040104 CARBON 1/8W(T) 5% 100K R451 FB246203 METAL 1/4W(T) 1% 620K...
  • Page 136 Part No for NPG SYMBOL DESCRIPTION R514 FA040103 CARBON 1/8W(T) 5% 10K R515 FA040103 CARBON 1/8W(T) 5% 10K R516 FA040473 CARBON 1/8W(T) 5% 47K R517 FA240103 CARBON 1/4W(T) 5% 10K R518 FA040222 CARBON 1/8W(T) 5% 2.2K R519 FA040103 CARBON 1/8W(T) 5% 10K R520 FA040472 CARBON 1/8W(T) 5% 4.7K...
  • Page 137 Part No for NPG SYMBOL DESCRIPTION R726 FA040103 CARBON 1/8W(T) 5% 10K R727 FA040472 CARBON 1/8W(T) 5% 4.7K R728 FA040103 CARBON 1/8W(T) 5% 10K R729 FA040472 CARBON 1/8W(T) 5% 4.7K R730 FA040472 CARBON 1/8W(T) 5% 4.7K R731 FA040472 CARBON 1/8W(T) 5% 4.7K R732 FA040101 CARBON 1/8W(T) 5% 100OHM...
  • Page 138 Part No for NPG SYMBOL DESCRIPTION C114 GA310655 ELECT 85°C/T 10U/50V M C115 GF222252 MEF CAP BOX 0.0022U/50V J C116 GB210458 CERAMIC Y5V/T 0.1U/50V Z C117 GB615152 CERAMIC SL/T 150P/50V J C118 GB747153 CC Y5P(B)/T 470P/50V K C119 GF233252 MEF CAP BOX 0.0033U/50V J C120 GA347755 ELECT 85OC/T 470U/50V M...
  • Page 139 Part No for NPG SYMBOL DESCRIPTION C274 GB7102F3 CC Y5P(B)/T 1000P/500V K C275 GB7222F3 CERAMIC Y5P(B) 2200P/500V C276 GA222675 ELECT 105°C/T 22U/100V M C277 GAA10575 ELECT 85C/A 1U/100V M C278 GB7102F3 CC Y5P(B)/T 1000P/500V K C279 GF222462 MEF CAP BOX 0.22U/63V J C27A GB618152 CERAMIC SL/T 180P/50V J...
  • Page 140 Part No for NPG SYMBOL DESCRIPTION C324 GB7471F3 CC Y5P(B)/T 470P/500V K C326 GB910358 CC Z5V(F)/T 0.01U/50V Z C327 GF210462 MEF CAP BOX 0.1U/63V J C328 GB210458 CERAMIC Y5V/T 0.1U/50V Z C329 GF210272 MEF CAP BOX 0.001U/100V J C330 GF210252 MEF CAP BOX 0.001U/50V J C331 GFB10482...
  • Page 141 Part No for NPG SYMBOL DESCRIPTION C411 GA310745 ELECT 85C/T 100U/35VM C412 GB710253 CC Y5P(B)/T 1000P/50V K C415 GB710253 CC Y5P(B)/T 1000P/50V K C416 GB710253 CC Y5P(B)/T 1000P/50V K C452 GA310555 ELECT 85°C/T 1U/50V M C453 GB210458 CERAMIC Y5V/T 0.1U/50V Z C454 GA310555 ELECT 85°C/T 1U/50V M...
  • Page 142 Part No for NPG SYMBOL DESCRIPTION C702 GB210458 CERAMIC Y5V/T 0.1U/50V Z C703 GA310725 ELECT 85°C/T 100U/16V M C704 GB633052 CERAMIC SL/T 33P/50V J C705 GB633052 CERAMIC SL/T 33P/50V J C706 GB610152 CERAMIC SL/T 100P/50V J C709 GB722153 CERAMIC Y5P(B)/T 220P/50V C710 GB722153 CERAMIC Y5P(B)/T 220P/50V...
  • Page 143 REPLACEMENT PARTS LIST (For Europe) The components specified for Model DPro930SB(B) SYMBOL Part No for NPG DESCRIPTION *** ICS *** U101 DD002600 IC LINEAR KA3842A 8P U201 80016621 IC LM1267 U202 EH110051 IC MTV030N-46 20PIN U203 80010891 IC LM2480 U204 EH110071 IC LM2463 U301...
  • Page 144 Part No for NPG SYMBOL DESCRIPTION Q313 EF206301 FET N YTAF630 TO-220F Q314 80008151 TR NPN 2SC5587 TO-3P Q315 EF206301 FET N YTAF630 TO-220F Q316 80014321 TR NPN KRC102M TO-92(T) Q317 80003311 FET N YTAF640 TO-220F Q318 80014321 TR NPN KRC102M TO-92(T) Q319 80003311 FET N YTAF640 TO-220F...
  • Page 145 Part No for NPG SYMBOL DESCRIPTION D112 EJ044148 DIODE T" 1N4148" D113 EJ044148 DIODE T" 1N4148" D115 EJ044148 DIODE T" 1N4148" D116 EJ044148 DIODE T" 1N4148" D117 EJ044148 DIODE T" 1N4148" D118 80003821 DIODE 1A/1KV UF4007 D041 D120 EJ044148 DIODE T" 1N4148" D131 EJAC0010 DIODE/T 1A 1N4007...
  • Page 146 Part No for NPG SYMBOL DESCRIPTION D317 EJB00004 DIODE/A 5TUZ47 D318 80003821 DIODE 1A/1KV UF4007 D041 D319 EJ044148 DIODE T" 1N4148" D320 EJA00018 DIODE/T 1A UF4006 D321 80003841 DIODE 1A/20V UF4003 DG41 D322 80009741 DIODE/T UF4005 D323 EJA00018 DIODE/T 1A UF4006 D401 EJB00017 DIODE/A 1A IN4936...
  • Page 147 Part No for NPG SYMBOL DESCRIPTION T302 HE300011 TRANS DF X'FM EI-22 N2901 T304 HE200011 TRANS HDDRIVE X'FM EI-19 *** VARIABLE RESISTORS *** VR101 FF300501 VR CARBON 6MM 500H/B VR301 FF310223 VR CARBON 6MM 22K VR302 FF310223 VR CARBON 6MM 22K VR501 FF310502 VR CARBON 6MM 5K...
  • Page 148 Part No for NPG SYMBOL DESCRIPTION L231 HB013278 PACKING COIL /T 0.27UH K L250 HB013228 PEAKING COIL/T 0.22UH K L251 HB013188 PEAKING COIL/T 0.18UH K L301 80016071 CHOCK COIL 14UH P75 L501 80016081 CHOCK COIL 8.0MH (DRWW16* RL181 80003761 REPLY 12V 6P OSA-SS-212DM T303 HA300011 L LINER N2901...
  • Page 149 Part No for NPG SYMBOL DESCRIPTION R102 FA330333 CARBON 1/2W(T) 5% 33K R103 FA330333 CARBON 1/2W(T) 5% 33K R104 FA240564 CARBON 1/4W(T) 5% 560K R105 FA240564 CARBON 1/4W(T) 5% 560K R106 FB244708 METAL 1/4W(T) 1% 4.7H R107 FB240010 METAL 1/4W(T) 1% 1OHM R108 FA040100 CARBON 1/8W(T) 5% 10OHM...
  • Page 150 Part No for NPG SYMBOL DESCRIPTION R166 FA040220 CARBON 1/8W(T) 5% 22H R167 FA040103 CARBON 1/8W(T) 5% 10K R181 FA040392 CARBON 1/8W(T) 5% 3.9K R201 FA040562 CARBON 1/8W(T) 5% 5.6K R202 FA040334 CARBON 1/8W(T) 5% 330K R203 FA040332 CARBON 1/8W(T) 5% 3.3K R204 FA040472 CARBON 1/8W(T) 5% 4.7K...
  • Page 151 Part No for NPG SYMBOL DESCRIPTION R281 FA040102 CARBON 1/8W(T) 5% 1K R282 FA040101 CARBON 1/8W(T) 5% 100OHM R283 FA040472 CARBON 1/8W(T) 5% 4.7K R284 FA040101 CARBON 1/8W(T) 5% 100OHM R285 FA040103 CARBON 1/8W(T) 5% 10K R286 FA040123 CARBON 1/8W(T) 5% 12K R287 FA040102 CARBON 1/8W(T) 5% 1K...
  • Page 152 Part No for NPG SYMBOL DESCRIPTION R340 FB570101 MOF 2W/M(B) 5% 100H R342 FA040100 CARBON 1/8W(T) 5% 10OHM R344 FA040103 CARBON 1/8W(T) 5% 10K R345 FA040331 CARBON 1/8W(T) 5% 330H R346 FA330101 CARBON 1/2W(T) 5% 100OHM R347 FA360270 CARBON 1/2W/M(T) 5% 27H R348 FK010010 R MOF 5W 1.2J (AI)
  • Page 153 Part No for NPG SYMBOL DESCRIPTION R405 FB275601 METAL 1/4W/M(T) 1% 5.6K R406 FB271801 METAL 1/4W/M(T) 1% 1.8K F R407 FB470758 MOF 1W/M(A) 5% 0.75H R408 FA330271 CARBON 1/2W(T)5% 270H R409 FB275601 METAL 1/4W/M(T) 1% 5.6K R410 FB271801 METAL 1/4W/M(T) 1% 1.8K F R411 FA240222 CARBON 1/4W(T) 5% 2.2K...
  • Page 154 Part No for NPG SYMBOL DESCRIPTION R509 FA040103 CARBON 1/8W(T) 5% 10K R510 FA040103 CARBON 1/8W(T) 5% 10K R511 FB241802 METAL 1/4W(T) 1% 18K R512 FA040153 CARBON 1/8W(T) 5% 15K R513 FA240102 CARBON 1/4W 5% 1KOHM R514 FA040103 CARBON 1/8W(T) 5% 10K R515 FA040103 CARBON 1/8W(T) 5% 10K...
  • Page 155 Part No for NPG SYMBOL DESCRIPTION R721 FA040101 CARBON 1/8W(T) 5% 100OHM R722 FA040103 CARBON 1/8W(T) 5% 10K R723 FA040101 CARBON 1/8W(T) 5% 100OHM R724 FA040103 CARBON 1/8W(T) 5% 10K R725 FA040103 CARBON 1/8W(T) 5% 10K R726 FA040103 CARBON 1/8W(T) 5% 10K R727 FA040472 CARBON 1/8W(T) 5% 4.7K...
  • Page 156 Part No for NPG SYMBOL DESCRIPTION C109 GB7103H3 CERAMIC Y5P(B)/T0.01U/1KV C110 GA310655 ELECT 85°C/T 10U/50V M C111 GAA22745 ELECT 85C/A 220U/35V M C112 GA310655 ELECT 85°C/T 10U/50V M C113 GA310655 ELECT 85°C/T 10U/50V M C114 GA310655 ELECT 85°C/T 10U/50V M C115 GF222252 MEF CAP BOX 0.0022U/50V J...
  • Page 157 Part No for NPG SYMBOL DESCRIPTION C253 GA210575 C,ELEC 1UF 100V M C254 GB712152 CERAMIC Y5P(B)/T 120P/50V C270 GB656052 CERAMIC SL/T 56P/50V C272 GA247625 ELECT 105°C/T 47U/16V M C273 GB910358 CC Z5V(F)/T 0.01U/50V Z C274 GB7102F3 CC Y5P(B)/T 1000P/500V K C275 GB7222F3 CERAMIC Y5P(B) 2200P/500V...
  • Page 158 Part No for NPG SYMBOL DESCRIPTION C317 GB7272H3 CERAMIC Y5P(B)/T 2700P/1K C320 GAA22775 ELECT 85OC/A 220U/100V M C321 GA347635 ELECT 85°C/T 47U/25V M C322 GAB10835 ELECT 105°C/A1000U/25V M C323 GA310555 ELECT 85°C/T 1U/50V M C324 GB7471F3 CC Y5P(B)/T 470P/500V K C326 GB910358 CC Z5V(F)/T 0.01U/50V Z...
  • Page 159 Part No for NPG SYMBOL DESCRIPTION C406 GB722253 CC Y5P(B)/T 2200P/50V K C407 GB710253 CC Y5P(B)/T 1000P/50V K C408 GF210352 MEF CAP BOX 0.01U/50V J C409 GA310555 ELECT 85°C/T 1U/50V M C410 GFB10482 PLASTIC MPP/A 0.10U/250VJ C411 GA310745 ELECT 85C/T 100U/35VM C412 GB710253 CC Y5P(B)/T 1000P/50V K...
  • Page 160 Part No for NPG SYMBOL DESCRIPTION C522 GB610153 CERAMIC SL/T 100P/50V K C523 GFD47482 PLASTIC MPPS/A 0.47U/250V C524 GB722253 CC Y5P(B)/T 2200P/50V K C525 GA410655 ELECT NP/T 10U/50V M C701 GE210352 CQ PEI/T 0.01U/50V J C702 GB210458 CERAMIC Y5V/T 0.1U/50V Z C703 GA310725 ELECT 85°C/T 100U/16V M...
  • Page 161 REPLACEMENT PARTS LIST (For Europe) The components specified for Model DPro930SB-BK(B) Part No for NPG SYMBOL DESCRIPTION *** ICS *** U101 DD002600 IC LINEAR KA3842A 8P U201 80016621 IC LM1267 U202 EH110051 IC MTV030N-46 20PIN U203 80010891 IC LM2480 U204...
  • Page 162 Part No for NPG SYMBOL DESCRIPTION Q313 EF206301 FET N YTAF630 TO-220F Q314 80008151 TR NPN 2SC5587 TO-3P Q315 EF206301 FET N YTAF630 TO-220F Q316 80014321 TR NPN KRC102M TO-92(T) Q317 80003311 FET N YTAF640 TO-220F Q318 80014321 TR NPN KRC102M TO-92(T) Q319 80003311 FET N YTAF640 TO-220F...
  • Page 163 Part No for NPG SYMBOL DESCRIPTION D112 EJ044148 DIODE T" 1N4148" D113 EJ044148 DIODE T" 1N4148" D115 EJ044148 DIODE T" 1N4148" D116 EJ044148 DIODE T" 1N4148" D117 EJ044148 DIODE T" 1N4148" D118 80003821 DIODE 1A/1KV UF4007 D041 D120 EJ044148 DIODE T" 1N4148" D131 EJAC0010 DIODE/T 1A 1N4007...
  • Page 164 Part No for NPG SYMBOL DESCRIPTION D317 EJB00004 DIODE/A 5TUZ47 D318 80003821 DIODE 1A/1KV UF4007 D041 D319 EJ044148 DIODE T" 1N4148" D320 EJA00018 DIODE/T 1A UF4006 D321 80003841 DIODE 1A/20V UF4003 DG41 D322 80009741 DIODE/T UF4005 D323 EJA00018 DIODE/T 1A UF4006 D401 EJB00017 DIODE/A 1A IN4936...
  • Page 165 Part No for NPG SYMBOL DESCRIPTION T302 HE300011 TRANS DF X'FM EI-22 N2901 T304 HE200011 TRANS HDDRIVE X'FM EI-19 *** VARIABLE RESISTORS *** VR101 FF300501 VR CARBON 6MM 500H/B VR301 FF310223 VR CARBON 6MM 22K VR302 FF310223 VR CARBON 6MM 22K VR501 FF310502 VR CARBON 6MM 5K...
  • Page 166 Part No for NPG SYMBOL DESCRIPTION L231 HB013278 PACKING COIL /T 0.27UH K L250 HB013228 PEAKING COIL/T 0.22UH K L251 HB013188 PEAKING COIL/T 0.18UH K L301 80016071 CHOCK COIL 14UH P75 L501 80016081 CHOCK COIL 8.0MH (DRWW16* RL181 80003761 REPLY 12V 6P OSA-SS-212DM T303 HA300011 L LINER N2901...
  • Page 167 Part No for NPG SYMBOL DESCRIPTION *** RESISTORS *** J152 FA040101 CARBON 1/8W(T) 5% 100OHM J153 FA040101 CARBON 1/8W(T) 5% 100OHM R101 FA330684 CARBON 1/2W(T) 5% 680K R102 FA330333 CARBON 1/2W(T) 5% 33K R103 FA330333 CARBON 1/2W(T) 5% 33K R104 FA240564 CARBON 1/4W(T) 5% 560K R105...
  • Page 168 Part No for NPG SYMBOL DESCRIPTION R162 FA240511 CARBON 1/4W(T) 5% 510H R163 FA040472 CARBON 1/8W(T) 5% 4.7K R164 FA330109 CARBON 1/2W (T) 5% 1OHM R165 FA330102 CARBON 1/2W(T) 5% 1K R166 FA040220 CARBON 1/8W(T) 5% 22H R167 FA040103 CARBON 1/8W(T) 5% 10K R181 FA040392 CARBON 1/8W(T) 5% 3.9K...
  • Page 169 Part No for NPG SYMBOL DESCRIPTION R278 FA040102 CARBON 1/8W(T) 5% 1K R279 FB241002 METAL 1/4W(T) 1% 10K R27A FA040473 CARBON 1/8W(T) 5% 47K R280 FB470279 MOF 1W/M(A) 5% 2.7H R281 FA040102 CARBON 1/8W(T) 5% 1K R282 FA040101 CARBON 1/8W(T) 5% 100OHM R283 FA040472 CARBON 1/8W(T) 5% 4.7K...
  • Page 170 Part No for NPG SYMBOL DESCRIPTION R336 FA040223 CARBON 1/8W(T) 5% 22K R337 FB470100 MOF 1W/M(A) 5% 10OHM R338 FA040103 CARBON 1/8W(T) 5% 10K R339 FB480471 MOF 1W/M(B) 5% 470H R340 FB570101 MOF 2W/M(B) 5% 100H R342 FA040100 CARBON 1/8W(T) 5% 10OHM R344 FA040103 CARBON 1/8W(T) 5% 10K...
  • Page 171 Part No for NPG SYMBOL DESCRIPTION R392 FA040103 CARBON 1/8W(T) 5% 10K R402 FA330271 CARBON 1/2W(T)5% 270H R403 FB470010 MOF 1W/M(A) 5% 1H R404 FA240229 CARBON 1/4W(T) 5% 2.2H R405 FB275601 METAL 1/4W/M(T) 1% 5.6K R406 FB271801 METAL 1/4W/M(T) 1% 1.8K F R407 FB470758 MOF 1W/M(A) 5% 0.75H...
  • Page 172 Part No for NPG SYMBOL DESCRIPTION R505 FB242611 METAL 1/4W(T) 1% 2.61K R506 FB246040 METAL 1/4W(T) 1% 604OHM R507 FA040101 CARBON 1/8W(T) 5% 100OHM R508 FA040101 CARBON 1/8W(T) 5% 100OHM R509 FA040103 CARBON 1/8W(T) 5% 10K R510 FA040103 CARBON 1/8W(T) 5% 10K R511 FB241802 METAL 1/4W(T) 1% 18K...
  • Page 173 Part No for NPG SYMBOL DESCRIPTION R715 FA040472 CARBON 1/8W(T) 5% 4.7K R716 FA040472 CARBON 1/8W(T) 5% 4.7K R717 FA040472 CARBON 1/8W(T) 5% 4.7K R719 FA040101 CARBON 1/8W(T) 5% 100OHM R721 FA040101 CARBON 1/8W(T) 5% 100OHM R722 FA040103 CARBON 1/8W(T) 5% 10K R723 FA040101 CARBON 1/8W(T) 5% 100OHM...
  • Page 174 Part No for NPG SYMBOL DESCRIPTION C105 GJH102E5 SAFE Y-CAP/S 1000P/400V M C106 GJH102E5 SAFE Y-CAP/S 1000P/400V M C107 GKA337E5 POWER ELECT 85C 330U/400V C108 GA347625 ELECT 85°C/T 47U/16V M C109 GB7103H3 CERAMIC Y5P(B)/T0.01U/1KV C110 GA310655 ELECT 85°C/T 10U/50V M C111 GAA22745 ELECT 85C/A 220U/35V M...
  • Page 175 Part No for NPG SYMBOL DESCRIPTION C234 GB712152 CERAMIC Y5P(B)/T 120P/50V C250 GB210458 CERAMIC Y5V/T 0.1U/50V Z C251 GB910358 CC Z5V(F)/T 0.01U/50V Z C252 GA410575 ELECT NP/T 1U/100V M C253 GA210575 C,ELEC 1UF 100V M C254 GB712152 CERAMIC Y5P(B)/T 120P/50V C270 GB656052 CERAMIC SL/T 56P/50V...
  • Page 176 Part No for NPG SYMBOL DESCRIPTION C312 GA347655 C,ELEC 47UF 50V M C313 GAA47585 ELECT 85°C/A 4.7U/250V M C314 GA322555 ELECT 85°C/T 2.2U/50V M C316 GB910358 CC Z5V(F)/T 0.01U/50V Z C317 GB7272H3 CERAMIC Y5P(B)/T 2700P/1K C320 GAA22775 ELECT 85OC/A 220U/100V M C321 GA347635 ELECT 85°C/T 47U/25V M...
  • Page 177 Part No for NPG SYMBOL DESCRIPTION C402 GB722253 CC Y5P(B)/T 2200P/50V K C403 GAA47735 ELECT 85C/A 470U/25V M C404 GF222472 MEF CAP BOX 0.22U/100V J C405 GB722253 CC Y5P(B)/T 2200P/50V K C406 GB722253 CC Y5P(B)/T 2200P/50V K C407 GB710253 CC Y5P(B)/T 1000P/50V K C408 GF210352 MEF CAP BOX 0.01U/50V J...
  • Page 178 Part No for NPG SYMBOL DESCRIPTION C518 GA310725 ELECT 85°C/T 100U/16V M C519 GA310725 ELECT 85°C/T 100U/16V M C520 GF222452 MEF CAP BOX 0.22U/50V J C521 GB610153 CERAMIC SL/T 100P/50V K C522 GB610153 CERAMIC SL/T 100P/50V K C523 GFD47482 PLASTIC MPPS/A 0.47U/250V C524 GB722253 CC Y5P(B)/T 2200P/50V K...
  • Page 179 BLOCK DIAGRAM (FP912SB / DPro930SB) Convergence Rotation Control Control R-OUT Video Pre-AMP Video Output R, G, B Input G-OUT U201 AMP U203 B-OUT Control Key Video Bias U703 U203 14VSW -14VSW Horizontal & H/H+V OSD Process Vertical AMP V-DY Vertical Process Micro-Processor U202 Output U401...
  • Page 180 SCHEMATIC DIAGRAM MAIN PWB 10-1...
  • Page 181 SCHEMATIC DIAGRAM CRT PWB 10-2...
  • Page 182 WAVE FORM MAIN PWB 2Vp-p 6.72Vp-p 35us 32.0us 32.0us PMS MODE ON MODE 9Vp-p 17.50Vp-p 11.7us 81Vp-p 29.7Vp-p 13.3Vp-p 7.5Vp-p -15.6Vp-p 650ms ON MODE 47kHz 12MHz 12MHz 5.69Vp-p 5.44Vp-p 756mVp-p PMS MODE 5Vp-p 5.06Vp-p 4.94Vp-p 16.89ms 16.59ms 31.79us 2.91Vp-p 1.664V0-p 5.11Vp-p 10-3...
  • Page 183 1195Vp-p 12.87Vp-p 1.175Vp-p 30V0-p 26.33Vp-p 47.2Vp-p 1203Vp-p 24V0-p 3.53Vp-p 3.03Vp-p -29.8Vp-p 12.42Vp-p 3.11Vp-p 48.9Vp-p 331Vp-p 128.1Vp-p 29.1Vp-p 170Vp-p 588Vp-p 10-4...

  • Page 184: Packing Specification

    Packing specification A version NaViSet Carton Box Flyer 11-1...
  • Page 185 ITEM DESCRIPTION Part No for NPG CARTON BOX DPRO930BBK(A) 13202041 POLYLON(B) 13400771 POLYLON(T) 13400761 PE BAG(500*480*850+WARNIN 13700301 NAVISET CARTON BOX FLYER 15900251 OWNERS MANUAL DPRO930SB(A 15501391 BAG POLYETHYLENE 13700021 POWER CORD2P2MCOLORSG8508 80001631 11-2...
  • Page 186 B version SALES OFFICE LIST (MITSUBISHI) (10) 11-3...
  • Page 187 ITEM DESCRIPTION Part No for NPG CARTON BOX DPRO930BBK(B) 13202051 POLYLON(B) 13400771 POLYLON(T) 13400761 PE BAG(500*480*850+WARNIN 13700301 NAVISET CARTON BOX FLYER 15900251 SALES OFFICE LIST (MITSUB 15900261 OWNERS MANUAL DPRO930SB(B 15501401 BAG POLYETHYLENE 13700021 POWER CORD 3P 1.8M EUROPE 80001651 (10) POWER CORD 3P 1.8M U.K.

This manual is also suitable for:

Dpro930sb-bkabDpro930sb-bkaDpro930sb-bkb

Table of Contents