Permanently lubricated single stage portable (48 pages)
Summary of Contents for Craftsman 919.184160
Page 1
OWNERS MANUAL SINGLE STAGE AIR COMPRESSOR MODEL NO. 919.184160 Record in the spaces provided. (1) The model number which can be found on the label on the front of the air tank saddle. (2) The code number which can be found on the foil label on the side of the air tank.
TABLE OF CONTENTS Page SAFETY GUIDELINES ................WARNING CHART ................. 3-5 SPECIFICATION CHART ..............GLOSSARY .................... ACCESSORIES FOR USE WITH SEARS AIR COMPRESSORS ............GENERAL INFORMATION ..............DESCRIPTION OF OPERATION ............INSTALLATION AND BREAK-IN PROCEDURES ......... 7-9 Location of Air Compressor .............. Piping ....................
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. HAZARD RISK OF EXPLOSION OR FIRE WHAT CAN HAPPEN HOW TO PREVENT IT IT IS NORMAL FOR ELECTRICAL CONTACTS WITHIN THE ALWAYS OPERATE THE COMPRESSOR IN A WELL VENTI-...
HAZARD RISK FROM FLYING OBJECTS WHAT CAN HAPPEN HOW TO PREVENT IT THE COMPRESSED AIR STREAM CAN CAUSE SOFT TISSUE ALWAYS WEAR ANSI Z87.1 APPROVED SAFETY GLASSES DAMAGE TO EXPOSED SKIN AND CAN PROPEL DIRT, CHIPS, WITH SIDE SHIELDS WHEN USING THE COMPRESSOR. LOOSE PARTICLES AND SMALL OBJECTS AT HIGH SPEED, NEVER POINT ANY NOZZLE OR SPRAYER TOWARD ANY RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY.
HAZARD RISK FROM MOVING PARTS WHAT CAN HAPPEN HOW TO PREVENT IT MOVING PARTS SUCH AS THE PULLEY, FLYWHEEL AND BELT NEVER OPERATE THE COMPRESSOR WITH GUARDS OR CAN CAUSE SERIOUS INJURY IF THEY COME INTO CONTACT COVERS WHICH ARE DAMAGED OR REMOVED. WITH YOU OR YOUR CLOTHING.
SPECIFICATION CHART Model No. 919.184160 Max. Developed HP Displacement CFM at Max. Pressure Bore 2 7/8 Stroke 2" Voltage - Single Phase Minimum Branch Circuit Requirement 20 amp *Fuse Type Fusetron Type "T" Amperage at Max. Pressure Air Tank Capacity - Gallons...
GENERAL INFORMATION You have purchased an air compressor unit consisting of Separate air transformers which combine the functions of air regulation and/or moisture and dirt removal should be a two cylinder, single stage air compressor pump, an used where applicable. ASME air tank, associated controls and instruments.
top of the oil fill hole. (It must not be allowed to be lower EXCESSIVE VIBRATION MAY WEAKEN THE than 3/8" - 6 threads down - from the top.) When filling the AIR TANK AND CAUSE AN EXPLOSION. crankcase, the oil flows very slowly. If the oil is added too THE OUTFIT MUST BE MOUNTED AS quickly, it will overflow and appear to be full.
Open the shut-off valve fully, to permit air to escape Break-In Procedures and to prevent pressure build-up in the air tank. Turn ON the air compressor. Run the air compressor for 30 minutes to seal the Serious damage may result if the following rings and lubricate all internal surfaces.
5. Apply sealant to the check valve threads.Reinstall A dirty air filter will not allow the compressor to operate the check valve (turn clockwise). The valve stem at full capacity. Before you use the compressor, check should still move freely do not over tighten. the air filter to be sure it is clean.
NOTE Pulley and Flywheel - Alignment The belt should be centered over the The compressor flywheel and motor pulley must be inline grooves on the flywheel and motor pulley. (in the same plane) within 1/16" to assure belt retention within sheave grooves. The motor mounting holes on the Push the motor back into regular position and tighten saddle are skewed to square the motor with the com- bolts securely.
Page 12
CORRECTION PROBLEM CAUSE Motor overload protection switch has tripped. Let the motor cool off and reset switch by pressing Motor will not run. the red button located on the end of the motor. Tank pressure exceeds pressure switch "cut- Motor will start automatically when tank pressure in"...
PARTS LIST PART NUMBER DESCRIPTION Screw #8-32 x 3/8" (2 used) SSF-935 AC-0322 Filter Plate Assembly Felt Filter AC-0333 SSF-955 Screw 3/8"-16 x 1-1/2" (5 used - Torque 25 to 30 ft. lbs.) Head Assembly (includes 2 ea. Key #50 & 4 ea. Key #51) CAC-4213 Z-48 Head Gasket...
Page 18
For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week MODEL NO. 1-800-366-PART 919.184160 (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week When requesting service or ordering...
Page 19
MANUAL DEL OPERADOR COMPRESOR DE AIRE DE UNA ETAPA MODELO NO. 919.184160 Registrar el los espacios provistos. (1) El número de modelo que puede encontrarse en el rótulo en el frente de la montura del tanque. (2) El número de código que puede encontrarse en el rótulo metálico en un...
TABLA DE CONTENIDOS Página PAUTAS DE SEGURIDAD ..............TABLA DE ADVERTENCIAS ..............3-5 TABLA DE ESPECIFICACIONES ............GLOSARIO ..................... ACCESORIOS PARA USAY CON LOS COMPRESORES DE AIRE DE SEARS ................ INFORMACIÓN GENERAL ..............DESCRIPCIÓN DE LA OPERACIÓN ............. INSTALACIÓN Y PROCEDIMIENTOS PARA EL ASENTAMIENTO ..7-9 Ubicación del Compresor de Aire .............
Page 21
INSTRUCCIONES IMPORTANTES DE SEGURIDAD GUARDE ESTAS INSTRUCCIONES LA OPERACIÓN O EL MANTENIMIENTO INADECUADOS DE ESTE PRODUCTO PODRÍAN OCASIONAR SERIAS LESIONES Y DAÑOS A LA PROPIEDAD. LEA Y COMPRENDA TODAS LAS ADVERTENCIAS E INSTRUCCIONES DE FUNCIONAMIENTO ANTES DE UTILIZAR ESTE EQUIPO. PELIGRO RIESGO DE EXPLOSIÓN O INCENDIO ¿QUÉ...
Page 22
PELIGRO RIESGO DE OBJETOS ARROJADOS POR EL AIRE. ¿QUÉ PUEDE OCURRIR? ¿CÓMO PREVENIRLO? EL CHORRO DE AIRE COMPRIMIDO PUEDE CAUSAR DAÑOS SOBRE LOS AL UTILIZAR EL COMPRESOR, USE SIEMPRE ANTEOJOS DE SEGURIDAD TEJIDOS BLANDOS DE LA PIEL EXPUESTA, Y PUEDE PROPULSAR SUCIEDAD, Z87.1 APROBADOS, CON PROTECCIÓN LATERAL.
Page 23
PELIGRO RIESGO DE PARTES MÓVILES ¿QUÉ PUEDE OCURRIR? ¿CÓMO PREVENIRLO? PARTES MOVIBLES TALES COMO LA POLEA, EL VOLANTE Y LA CORREA NUNCA OPERE EL COMPRESOR SIN SUS DEFENSAS O SUS CUBIERTAS PODRÍAN SER LA CAUSA DE SERIAS LESIONES SI ELLAS ENTRARAN EN REMOVIDAS O DAÑADAS.
TABLA DE ESPECIFICACIONES Modelo No. 919.184160 Máx. HP desarrollado Desplazamiento CFM a Máx. Presión Orificio 2 7/8 Carrera del Pistón 2" Voltaje Monofásico 220 V Requerimiento Mínimo de Circuito 20 Amperios *Tipo de Fusible «Fusetron» Tipo T Amperaje a Máx. Presión 15 Amps.
INFORMACIÓN GENERAL Usted ha comprado una unidad compresora de aire que Los reguladores pueden comprarse en la mayoría de tienda consiste de dos bomba compresora de aire de 2 cilindros y una de Sears por medio del catálogo vigente de herramientas sola etapa, un tanque de aire ASME y controles e instrumentos manuales, eléctricas y neumáticas.
del orificio de llenado de aceite. (En ningún momento debe permitirse que esté a menos de 3/8” -- 6 vueltas de rosca por debajo del borde superior). Al llenar el cárter, el aceite fluye muy lentamente. Si se le agrega aceite muy rápido, el cárter se LAS VIBRACIONES EXCESIVAS PUEDEN rebalsará...
Procedimientos para el Asentamiento 3. Abrir completamente la válvula de corte de aire para permitir que el aire escape y evitar la acumulación de presión en el tanque. 4. Prender el compresor de aire. 5. Operar el compresor por 30 minutos para sellar los anillos Si no se observan las instrucciones para el y lubricar todas las superficies internas.
6. Volver a colocar el tubo de salida y ajustar las tuercas Un filtro sucio impedirá que el compresor opere a máxima superior e inferior del tubo. capacidad. Verificar que el filtro de aire esté limpio antes de usar el compresor. Válvula de Seguridad - Si estuviese sucio, sacar los tornillos y el retén del filtro.
NOTA Polea del Motor y Polea Volante La correa debe estar centrada sobre las ranuras de la - Alineamiento polea volante y de la polea del motor. La polea del motor y polea volante deben de estar en línea (en el mismo plano) con una tolerancia de 1/16”...
Page 30
SOLUCIÓN PROBLEMA CAUSA Dejar que se enfríe el motor y reposicionar el interruptor El motor no funciona. El interruptor de protección de sobrecarga ha presionando el botón rojo localizado en el extremo del saltado. motor. El motor arrancará automáticamente cuando la presión La presión del tanque excede la presión de “corte”...
Page 33
Rótulo de con el Rendimiento D20343 Tuerca de Fijación con Brida (se usan 4) SSF-8150 Rótulo - Mantenimiento LA-2269-1 Rótulo - Advertencia LA-3266 Rótulo - Logotipo de Craftsman LA-3105 Válvula de Drenaje SS-2707 Tanque de Aire - 60 galones TA-4438 Aliviador de Tensión SSW-7367...
Page 34
DIAGRAMA DE LA BOMBA DEL COMPRESOR (tapón de llenado de aceite) (tapón de drenaje de aceite) D20410 16 — SP...
Page 35
LISTA DE PARTES NÚMERO NÚMERO EN DIAMGRM. DE PARTE DESCRIPCIÓN Tornillo #8-32 x 3/8” (se usan 2) SSF-935 Juego de Placa de Filtro AC-0322 Filtro de Fieltro AC-0333 Perno de 3/8” - 16 x 1-1/2” (se usan 5 - Torque 25 a 30 Lbs. pie) SSF-955 Cabezal (Incluye 2 piezas #50 y 4 piezas #51) CAC-4213...
COMPRESOR DE AIRE MANUAL DE UNA ETAPA DE PARTES NÚMERO DE MODELO 919.184160 Para solicitar servicio de reparación o repuestos que usted necesite, llamar de 7 am a 7 pm, los 7 días de la semana al 1-800-366-PART Al ordenar repuestos, siempre dar la siguiente información:...