Table of Contents
Advertisement
Available languages
Available languages
22 • ENGLISH
Measure and mark work for cutting.
Support and secure work properly
(See Safety Rules and Instructions).
Use appropriate and required safety equipment
(See Safety Rules).
Secure and maintain work area (See Safety Rules).
With plug inserted and guard closed, make sure switch
turns saw on and off.
Warning! It is important to support the work properly
and to hold the saw firmly to prevent loss of control which
could cause personal injury. Fig. C illustrates recommended
hand position.
OPERATION
Switch
To operate the tool, depress the trigger switch (1). The
tool will continue to run as long as the trigger is depressed.
To turn the tool off, release the trigger switch (1). There
is no provision for locking the tool on, and the switch
should never be locked on by any other means.
Sawing
Warning! To reduce the risk of serious personal
injury,always hold the tool with both hands.
Let the blade run freely for a few seconds before
starting the cut.
Apply only a gentle pressure to the tool while performing
the cut.
Work with the shoe pressed against the workpiece.
HINTS FOR OPTIMUM USE
As some splintering along the line of cut on the top side
of the workpiece cannot be avoided, cut on the side
where splintering is acceptable.
Where splintering is to be minimized, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
Pocket Cutting (Fig. K)
Pocket cutting is used to cut a hole in a piece of
material without cutting from the side.
Measure and mark work.
Tilt saw forward and rest front of the shoe on material
to be cut. Align so that cut will begin at the back of the
drawn rectangle shown in Fig. K.
Using the retracting lever, retract blade guard to an
upward position, with the blade just clearing the material,
start motor and gradually lower the saw into the material.
Warning! As blade starts cutting the material, release
the retracting lever immediately.
Never tie the blade guard in a raised position.
When the shoe rests flat on the material being cut,
complete the cut in forward direction.
Allow the blade to come to a complete stop before
lifting saw from material.
When starting each new cut, repeat the above steps.
Wrench Storage (Fig. L)
The spanner wrench (8) can be stored on the saw shoe as
shown in Fig. L.
Attaching and Removing the Rip Fence (Fig. M)
The rip fence is used to saw in a straight line parallel to the
edge of the working piece.
Attaching
Loosen the locking knob (17).
Insert the rip fence (18) through the openings (19).
Slide the rip fence into the desired position.
Tighten the locking know.
Removing
Loosen the locking know.
Pull the rip fence out of the tool.
Note: If you do not have a proper fitting fence, use a
straight edge guide in contact with the edge of the shoe
to improve accuracy of cut and reduce the possibility of
binding and kickback.
Accessories
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
Warning! The use of any accessory not recommended
for use with this tool could be hazardous. Use only 7-1/4 "
(184mm) blades with 5/8" diameter arbor.
Exception: 7" (175mm) abrasive blades can be used.
When cutting metal, be careful of hot sparks which are
thrown by the blade.
MAINTENANCE
Your tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Warning! Before performing any maintenance, switch
off and unplug the tool.
Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Important! To assure product Safety and Reliability,
repairs, maintenance and adjustment (other than those
Hide quick links:
Advertisement
Table of Contents
