Bosch GOP 18 V-EC professional Original Instructions Manual page 8

OBJ_BUCH-1924-001.book Page 8 Monday, February 25, 2013 3:39 PM
8 | English
18 Vacuum hose*
19 Extraction adapter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Multi-Cutter
Article number
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01/2003
* dependent of the battery pack being used
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Removing the battery
The battery 5 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 3 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 5, press the battery unlocking button 3
and pull the battery out of the power tool toward the rear. Do
not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
6 indicate the charge condition of the battery 5. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 7 to indicate the charge condition. This is also
possible when the battery 5 is removed.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 7, then the bat-
tery is defective and must be replaced.
2 609 141 040 | (25.2.13)
Changing the Tool
 Before any work on the machine itself (e.g. mainte-
 Wear protective gloves when changing application
GOP 18 V-EC
3 601 HB0 0..
V= 18
Selecting the Application Tool/Accessory
-1
min 8000 –20000
° 1.4
kg 1.7*
* Optional accessory; for the complete accessories please see Bosch
Capacity
accessory programme.
2/3
1/3
<1/3
Reserve
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
tools/accessories. Contact with the application tool/ac-
cessoriy can lead to injuries.
Accessory
HCS wood seg-
ment saw blade*
BIM segment saw
blade*
HCS plunge cut
saw blades,
wood*
BIM plunge cut
saw blades,
metal*
BIM plunge cut
saw blade, wood
and metal*
HM-Riff segment
saw blade*
HM-Riff delta
plate*
Scraper, rigid*
Scraper, flexible* Silicone and other
Base plate for
sanding, series
Delta 93 mm*
Material
Wooden materials,
plastic
Wooden materials,
plastic, non-ferrous
metals
Wooden materials,
plastic, gypsum and
other soft materials
Metal (e.g. unhard-
ened nails, screws,
smaller profiles),
non-ferrous metals
Wood, metal, non-
ferrous metals
Grouting joints, soft
wall tiles, glass-fibre
reinforces plastic
and other abrasive
materials
Carpets, coverings
elastic materials
Depends on sanding
sheet
Bosch Power Tools