Sony CA4000 Operation Manual page 9

f USB connector (for USB flash drives)
Connects to a USB flash drive for saving/loading configuration
data files.
For details, see "Using a USB Flash Drive" (page 47).
g PROMPTER1 connector (BNC type)
The PROMPTER function is available when a camera control
unit is connected. Outputs prompter 1 signal (available when
connected to a camera control unit). When connected to a
camera control unit with two prompter inputs, the signal for
prompter 1 is output.
h PROMPTER2/MONITOR connector (BNC type)
Outputs prompter 2 signal.
Available only when connected to a camera control unit with a
prompter 2 input connector.
You can output a VBS signal, HD Y signal similar to the VF
connector, HD-SYNC signal, or SD-SYNC signal by selecting
the signal type in the menu.
For details about selecting the signal, see "Setting the Camera
Outputs" (page 18).
i SDI-MONI (serial digital interface) connector (BNC type)
Outputs an HD SDI signal or an HD PROMPTER signal.
For details configuring signals, see "Setting the Camera
Outputs" (page 18).
Operation panel
SY model (NTSC)
1
TALLY RET1
ON
OFF
2
MIC PGM1 PGM2
ON
3
OFF
PROD
INCOM
4
ENG
5
a Rear tally and tally switch
ON: Displays a tally light, for example, in response to a tally
input on the connected camera control unit or when a call
signal is initiated by pressing the CALL button.
OFF: Turns the tally light off.
Note
The front tally and rear tally can be turned on/off using the
menu.
b PGM1 (program 1) and PGM2 (program 2) knobs
Adjusts the audio listening level of program 1 and program 2,
respectively.
c MIC (microphone) switch
Switches the intercom headset microphone on/off.
6
7
RET
2 3 4
8
ASSIGNABLE
DISPLAY
9
OFF
0
MENU
CALL
qa
d Line selector switch
Selects the intercom line.
PROD: Producer line.
ENG: Engineer line.
e INCOM (intercom) knob
Adjusts the intercom audio volume.
f RET 1 (return video 1) button
Displays the return video 1 signal in the viewfinder while this
button is pressed.
g RET (return video) and 2/3/4 (return video 2/3/4
selector) switch
When using other return video systems in parallel with return
video 1, the return signal selected by the 2/3/4 switch is
displayed in the viewfinder while the RET button is pressed.
Note
The RET 1 button has priority over the RET (2/3/4) button if
both buttons are pressed.
h ASSIGNABLE button
You can assign one of various functions to this button using
the menu displayed in the viewfinder.
i Menu control knob (rotary encoder)
Turn to select menu items and settings in the menu displayed
in the viewfinder, then press to confirm the selection.
j DISPLAY/MENU switch
Selects the screen displayed in the viewfinder.
DISPLAY: Displays text information and messages showing
the operating status, center marker, safety zone marker,
and other indicators, in addition to the camera image.
Pressing the menu control button in display mode
switches the screen to the status display.
OFF: Displays the image only.
MENU: Displays menu, in addition to the camera image.
k CALL button
Turns on the red tally light and CALL light on the RCP-1000
series Remote Control Panel or MSU-1000 series Master
Setup Unit. Used to call the RCP or MSU operator.
CE model (PAL)
1
TALLY RET1
ON
OFF
2
MIC
PGM1 PGM2
LINE
PROD
3
OFF
ENG
ENG PROD
4
5
6
7
RET
2 3 4
8
ASSIGNABLE
DISPLAY
9
OFF
0
MENU
CALL
TRACKER
qa
qs
Name and Function of Parts
9