HP Business Desktop d500 Series Service & Reference Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. Business Desktop d500 Series
  6. Service & reference manual
HP Business Desktop d500 Series Service & Reference Manual

HP Business Desktop d500 Series Service & Reference Manual

Hp business desktop d500 series 3rd edition
Hide thumbs Also See for Business Desktop d500 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual
service reference guide
Business Desktop d500 Series
3rd Edition
This document provides information on the removal and replacement of all
parts as well as information on troubleshooting, Desktop Management, setup
utilities, SATA and PATA drives, safety, routine care, connector pin
assignments, POST error messages, and diagnostic indicator lights.
Document Part Number 336492-003

Advertisement

Table of Contents
loading

Related Manuals for HP Business Desktop d500 Series

Summary of Contents for HP Business Desktop d500 Series

  • Page 1 Business Desktop d500 Series 3rd Edition This document provides information on the removal and replacement of all parts as well as information on troubleshooting, Desktop Management, setup utilities, SATA and PATA drives, safety, routine care, connector pin assignments, POST error messages, and diagnostic indicator lights.
  • Page 3 Service Reference Guide Business Desktop d500 Series 3rd Edition Document Part Number: 336492-003 October 2003...
  • Page 4 © 2003 Hewlett-Packard Development Company, L.P. HP, Hewlett Packard, and the Hewlett-Packard logo are trademarks of Hewlett-Packard Company in the U.S. and other countries. Compaq and the Compaq logo re trademarks of Hewlett-Packard Development Company, L.P. in the U.S. and other countries.

  • Page 5: Table Of Contents

    3.3.1 HP Client Manager Software ........
  • Page 6 Contents 3.3.9 FailSafe Boot Block ROM ..........3–4 3.3.10Replicating Your Setup .
  • Page 7 Contents 5.2.2 Preventing Electrostatic Damage to Equipment....... . . 5–3 5.2.3 Personal Grounding Methods and Equipment .
  • Page 8 Contents 6.17Speaker ..............6–35 6.18Chassis Fan .
  • Page 9 Contents 8.4 Front Bezel ..............8–7 8.5 Memory .
  • Page 10 Contents viii 336492-003 Service Reference Guide, d500...

  • Page 11: Installing The Operating System

    The I386 directory and its subdirectories provide the HP- or Compaq-specific integration of the operating system for the computer model and include device drivers supported by Windows 2000.

  • Page 12: Converting To Ntfs

    The Microsoft Windows 2000 Professional, Windows XP Home, or Windows XP Professional operating system is preinstalled on the computer and will be configured automatically the first time the computer is turned on. The following HP software will also be installed at that time on selected models:...

  • Page 13: Setup Utilities And Diagnostics Features

    Establish and manage passwords and other security features. Establish and manage energy-saving timeouts. All features identified in this chapter may not be available on all HP products. Power-On Self-Test (POST) POST is a series of diagnostic tests that runs automatically when the system is turned on. POST...

  • Page 14: Computer Setup Utilities

    Setup Utilities and Diagnostics Features 2.2 Computer Setup Utilities Use Computer Setup Utilities (F10) to: Modify or restore factory default settings. Set the system date and time. Set, view, change, or verify the system configuration including settings for processor, graphics, memory, audio, storage, communications, and input devices. Modify the boot order of bootable devices such as hard drives, diskette drives, optical drives, or LS-120 drives.

  • Page 15: Using Computer Setup (F10) Utilities

    Setup Utilities and Diagnostics Features 2.2.1 Using Computer Setup (F10) Utilities Computer Setup can be accessed only by turning on the computer or restarting the system. To access the Computer Setup Utilities menu, complete the following steps: 1. Turn on or restart the computer. If you are in Windows, click Start >Shut Down >Restart the Computer.

  • Page 16: Computer Setup Menu

    Setup Utilities and Diagnostics Features 2.2.2 Computer Setup Menu Heading Option Description File System Information Lists product name, processor type/speed/stepping, cache size (L1/L2), system ROM family and version, installed memory size, chassis serial number, integrated MAC for enabled or embedded NIC (if applicable), and asset tracking number. About Displays copyright information.
  • Page 17 Setup Utilities and Diagnostics Features Heading Option Description Storage Device Drive Type Emulation Options (continued) Configuration (continued) (continued) (continued) ATAPI LS-120 None (treated as Other). Diskette (treated as diskette drive). Transfer Mode (IDE devices only) Specifies the active data transfer mode. Options (subject to device capabilities) are PIO 0, Max PIO, Enhanced DMA, Ultra DMA 0, and Max UDMA.
  • Page 18 Setup Utilities and Diagnostics Features Heading Option Description Storage Options Secondary IDE Controller * (continued) (continued) Allows you to enable or disable the secondary IDE/ATA controller. Diskette MBR Validation * Allows you to enable or disable strict validation of the diskette Master Boot Record (MBR).
  • Page 19 Setup Utilities and Diagnostics Features Heading Option Description Storage Boot Order Allows you to specify the order in which attached peripheral (continued) devices (such as a diskette drive, hard drive, optical drive, or network interface card) are checked for bootable operating system image.
  • Page 20 Setup Utilities and Diagnostics Features Heading Option Description Security DriveLock* Allows you to assign or modify a master or user password for (continued) select IDE hard drives (not supported on SCSI hard drives). When this feature is enabled, the user is prompted to provide one of the DriveLock passwords during POST.
  • Page 21 Setup Utilities and Diagnostics Features Heading Option Description Security Device Security* Enables/disables serial ports A and B, parallel port, front USB (continued) ports, all USB ports, system audio, network controllers (some models), Multibay devices (some models), and SCSI controllers (some models). Network Service Enables/disables the computer’s ability to boot from an Boot...
  • Page 22 Setup Utilities and Diagnostics Features Heading Option Description Advanced** Power-On Options Allows you to set: POST mode (QuickBoot, FullBoot, or FullBoot every 1-30 days). POST messages (enable/disable). Safe POST* (enable/disable). Enabling this feature allows the ROM to monitor add-in cards during boot. If an add-in card does not work or initialize correctly, then on the next boot all cards will be skipped during POST.
  • Page 23 Setup Utilities and Diagnostics Features Heading Option Description Advanced** Power-On Options Allows you to set: (continued) (continued) (continued) POST Delay (in seconds) (enable/disable). Enabling this feature will add a user-specified delay to the POST process. This delay is sometimes needed for hard disks on some PCI cards that spin up very slowly;...
  • Page 24 Setup Utilities and Diagnostics Features Heading Option Description Advanced** Bus Options* Allows you to enable or disable: (continued) PCI bus mastering, which allows a PCI device to take control of the PCI bus. PCI VGA palette snooping, which sets the VGA palette snooping bit in PCI configuration space;...

  • Page 25: Diagnostics For Windows

    Running tests is optional but recommended after installing or connecting a new device. Third party devices not supported by HP may not be detected. Save, print, or display the information generated by the utility. 2.3.1 Detecting Diagnostics for Windows Some computers ship with the Diagnostics for Windows preloaded, but not preinstalled.

  • Page 26: Using Categories In Diagnostics For Windows

    2.3.3 Using Categories in Diagnostics for Windows To use categories: 1. Click Start > HP Information Center > Diagnostics for Windows. You can also select the Diagnostics for Windows icon, located in the Control Panel. The screen displays the overview of the computer hardware and software.
  • Page 27 Setup Utilities and Diagnostics Features Menu Bar—File, Categories, Navigation, Level, Tab, Help At the top of the Diagnostics for Windows screen is the Menu Bar consisting of six pull-down menus. Selecting an item will provide the following information on the system: File—Save As, Print, Printer Setup, Exit Categories System—System board, ROM, date, and time...

  • Page 28: Running Diagnostic Tests In Diagnostics For Windows

    2.3.4 Running Diagnostic Tests in Diagnostics for Windows To run diagnostic tests: 1. Click Start > HP Information Center > Diagnostics for Windows. Alternately, you can access Diagnostics for Windows via the control panel. The screen displays the overview of the computer hardware and software. Five tabs are displayed below the row of icons: Overview, Test, Status, Log, and Error.

  • Page 29: Configuration Record

    2.4.2 Running Configuration Record To run this program: 1. Click Start > HP Information Center > Configuration Record. Alternately, you can access Diagnostics for Windows via the control panel. The Configuration Record utility has two view options: Show Changed Items Only and Show All.

  • Page 30: Remote Diagnostics Enabling Agent

    In addition, the Remote Diagnostics Enabling Agent identifies any computer hardware device problems signaled by the HP Management Agents. These hardware devices are automatically selected for testing by the Remote Diagnostics Enabling Agent.

  • Page 31: Restoring The Software

    Setup Utilities and Diagnostics Features 2.7 Restoring the Software The Windows operating system and software can be restored to its original state by using the Restore CD. See the Restore CD for complete instructions on using this feature. Service Reference Guide, d500 336492-003 2–19...
  • Page 32 Setup Utilities and Diagnostics Features 2–20 336492-003 Service Reference Guide, d500...

  • Page 33: Desktop Management

    Support for specific features described in this guide may vary by model or software version. Initial Configuration and Deployment HP computers come with a preinstalled system software image. After a brief software “unbundling” process, the computer is ready to be used.

  • Page 34: Remote System Installation

    F12 = Network Service Boot message appears in the lower-right corner of the HP logo screen. Follow the instructions on the screen to continue the process. The default boot order is a BIOS configuration setting that can be changed to always attempt to PXE boot.

  • Page 35: Altiris Pc Transplant Pro

    OS using easy-to-follow wizards. Altiris solutions provide easy-to-use software distribution capabilities. When used in conjunction with System Software Manager (Section 3.3.4), or the HP Client Manager, administrators can also update ROM BIOS and device driver software from a central console.

  • Page 36: Activeupdate

    Enabling the system administrator to perform this task remotely, on multiple computers and personal computers, results in a consistent deployment of and greater control over HP PC ROM images over the network.
  • Page 37 Desktop Management If the system ROM is valid, the system starts normally. If the system ROM fails the validation check, the FailSafe Boot Block ROM provides enough support to start the system from a ROMPaq diskette, which will program the system ROM with a valid image.

  • Page 38: 10Replicating Your Setup

    3. To replicate the configuration, click File > Restore from Diskette, and follow the instructions on the screen. System Software Manager (SSM) may also be used to distribute setup configurations to multiple http://www.hp.com/go/ssm computers. For more information, see 3.3.11 Dual-State Power Button With Advanced Configuration and Power Interface (ACPI) enabled for Windows 2000 and Windows XP, the power button can function either as an on/off switch or as a suspend button.

  • Page 39: 12Power Management

    Windows that is different from the version included with your computer, you must install corresponding device drivers and utilities to ensure that all features are supported and functioning properly. HP has made the task of locating, accessing, evaluating, and installing the latest support software http://www.hp.com/support easier. You can download the software from .

  • Page 40: Asset Tracking And Security

    HP also offers several solutions for controlling access to valuable components and information. Security features such as the Smart Cover Sensor and the Smart Cover Lock, available on select models, help to prevent unauthorized access to the internal components of the personal computer.
  • Page 41 Desktop Management Security Features Overview (Continued) Feature Purpose How It Is Established DriveLock Prevents unauthorized access From the Computer Setup to the data on specific hard Utilities (F10) menu. drives. This feature is available on select models only. Smart Cover Sensor Indicates that computer cover From the Computer Setup or side panel has been...

  • Page 42: Password Security

    Desktop Management Security Features Overview (Continued) Feature Purpose How It Is Established Cable Lock Provision Inhibits access to the interior of Install a cable lock to secure the computer to prevent the computer to a fixed unwanted configuration object. changes or component removal.

  • Page 43: Establishing A Power-On Password Using Computer Setup

    Desktop Management 3.4.3 Establishing a Power-On Password Using Computer Setup Establishing a power-on password through Computer Setup prevents access to the computer when power is turned on, unless the password is entered. When a power-on password is set, Computer Setup presents Password Options under the Security menu. Password options include Password Prompt on Warm Boot.

  • Page 44: Changing A Power-On Or Setup Password

    Desktop Management Changing a Power-On or Setup Password 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart the Computer. To change the setup password, run Computer Setup. 2. When the key icon appears, type your current password, a slash (/) or alternate delimiter character, your new password, another slash (/) or alternate delimiter character, and your new password again as shown: current password/new password/new password...

  • Page 45: Drivelock

    DriveLock-capable hard drives are detected. DriveLock is intended for HP customers for whom data security is the paramount concern. For such customers, the cost of the hard drive and the loss of the data stored on it is inconsequential when compared with the damage that could result from unauthorized access to its contents.

  • Page 46: Drivelock Applications

    Desktop Management typically performed by a system administrator, a master password should be set first. HP encourages system administrators to set a master password whether they plan to enable DriveLock or keep it disabled. This will give the administrator the ability to modify DriveLock settings if the drive is locked in the future.

  • Page 47: Smart Cover Sensor

    4. Before exiting, click File > Save Changes and Exit. Smart Cover Lock The Smart Cover Lock is a software-controllable cover lock featured on select HP computers. This lock prevents unauthorized access to the internal components. Computers ship with the Smart Cover Lock in the unlocked position.

  • Page 48: Locking The Smart Cover Lock

    PC component failure (such as processor or power supply) Forgotten password Ä CAUTION: The Smart Cover FailSafe Key is a specialized tool available from HP. Be prepared; order this key before you need one (Tamper-resistant wrench PN 166527-001 or tamper-resistant bits PN 166527-002).

  • Page 49: Master Boot Record Security

    Desktop Management 3.4.6 Master Boot Record Security The Master Boot Record (MBR) contains information needed to successfully boot from a disk and to access the data stored on the disk. Master Boot Record Security may prevent unintentional or malicious changes to the MBR, such as those caused by some computer viruses or by the incorrect use of certain disk utilities.

  • Page 50: Before You Partition Or Format The Current Bootable Disk

    3.4.9 Fingerprint Identification Technology Eliminating the need to enter user passwords, HP Fingerprint Identification Technology tightens network security, simplifies the login process, and reduces the costs associated with managing corporate networks. Affordably priced, it is not just for high-tech, high-security organizations anymore.

  • Page 51: Fault Notification And Recovery

    When a fault occurs, the computer displays a Local Alert message containing a description of the fault and any recommended actions. You can then view current system health by using the HP Client Manager Software. If the computer is connected to a network managed by HP Insight Manager, HP Client Manager Software, or other system management applications, the computer also sends a fault notice to the network management application.
  • Page 52 Desktop Management 3–20 336492-003 Service Reference Guide, d500...

  • Page 53: Serial And Parallel Ata Drive Guidelines And Features

    Serial and Parallel ATA Drive Guidelines and Features PATA and SATA Device Information Characteristic PATA SATA Number of pins/conductors in data cable 40/80 Number of pins in power cable Maximum data cable length 18 in (45.7 cm) 39.37 in (100 cm) Data interface voltage differential 600 mV Drive motor voltages...

  • Page 54: Sata Power Cable

    Serial and Parallel ATA Drive Guidelines and Features 4.2.2 SATA Power Cable Usage Notes Usage Notes V3.3 3.3 V power 5 V power V3.3 3.3 V power Ground V3.3 3.3 V power Reserved Ground Ground Ground V 12 12 V power Ground 12 V power 5 V power...

  • Page 55: Pata Cable Layout

    Serial and Parallel ATA Drive Guidelines and Features 4.2.5 PATA Cable Layout The faces of industry-standard cable connectors are color-coded for easy recognition: System board connector = blue face Device 0 connector = black face Device 1 connector = gray face The color code of an industry-standard cable is applicable only if the drive’s jumper is in the cable-select position.

  • Page 56: Pata Device Classes

    Serial and Parallel ATA Drive Guidelines and Features Any drive attached to a channel must have a drive designation. If only a single drive is connected to a channel and its jumper is in the cable-select position, it is designated as the primary drive (Drive/Device 0) by its attachment to the Drive/Device 0 cable position.

  • Page 57: Pata Attach Sequence Rules By Class Priority

    Serial and Parallel ATA Drive Guidelines and Features 4.3.2 PATA Attach Sequence Rules by Class Priority Drives should be attached in the sequence shown for optimum performance starting at position 1. Primary Channel* Secondary Channel Device 1 Device 0 *If there are three or more devices, two or more of which are hard drives, two hard drives should be attached to the primary channel first before following the General Attach Sequence Rule.

  • Page 58: Pata Attach Sequence Worksheet

    Serial and Parallel ATA Drive Guidelines and Features 4.3.3 PATA Attach Sequence Worksheet Use the worksheet below for obtaining optimum system performance when setting up a computer with multiple drives. Use the General Attach Sequence Rule to determine the best drive installation sequence.
  • Page 59 Serial and Parallel ATA Drive Guidelines and Features Example 1: Three-Device Installation Sample A system has three devices: Ultra ATA-100 hard drive, CD-ROM drive, and a DVD drive. Using the Device Class Table in Section 4.3.1, the devices may be identified as: Ultra ATA-100 hard drive = Class 1 DVD drive = Class 2 CD-ROM drive = Class 3...

  • Page 60: Pata Additional Drive Application Notes

    Serial and Parallel ATA Drive Guidelines and Features Example 2: Four-Device Installation Sample A system has four devices: two Ultra ATA-100 hard drives, one DVD-CDR/W drive, and a ZIP-250 drive. Using the Device Class Table in Section 4.3.1, the devices may be reidentified as: Ultra ATA-100 hard drive = Class 1 Ultra ATA-100 hard drive = Class 1 DVD-CDR/W drive = Class 2...

  • Page 61: Pata Smart Drives

    Serial and Parallel ATA Drive Guidelines and Features 4.4 PATA SMART Drives The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP Personal Computers have built-in drive failure prediction that warns the user or network administrator of an impending failure or crash of the hard drive. The SMART drive tracks fault prediction and failure indication parameters such as reallocated sector count, spin retry count, and calibration retry count.

  • Page 62: Legacy Mode

    Serial and Parallel ATA Drive Guidelines and Features 4.6.1 Legacy Mode The Legacy mode is used to access devices attached to the embedded IDE controllers. Each channel requires two fixed I/O address ranges and an IRQ for each. Primary Channel Command block: 1F0h - 1F7h Control block: 3F6h IRQ: 14...

  • Page 63: Mixed Devices Boot And Drive Letter Ordering

    Serial and Parallel ATA Drive Guidelines and Features 4.7 Mixed Devices Boot and Drive Letter Ordering HDD Boot and Drive SATA Configuration* Controller Order Letter Ordering Add as a separate channel A. Integrated IDE A1. IDE Primary Device 0 (default). Used with Windows B.
  • Page 64 Serial and Parallel ATA Drive Guidelines and Features 4–12 336492-003 Service Reference Guide, d500...

  • Page 65: Identifying The Chassis, Routine Care, And Disassembly Preparation

    Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides general service information for the computer. Adherence to the procedures and precautions described in this chapter is essential for proper service. CAUTION: When the computer is plugged into an AC power source voltage is always applied to the Ä...

  • Page 66: Small Form Factor (Sff)

    Identifying the Chassis, Routine Care, and Disassembly Preparation 5.1.2 Small Form Factor (SFF) 5.1.3 Ultra-Slim Desktop (USDT) 5–2 336492-003 Service Reference Guide, d500...

  • Page 67: Electrostatic Discharge Information

    Identifying the Chassis, Routine Care, and Disassembly Preparation 5.2 Electrostatic Discharge Information A sudden discharge of static electricity from your finger or other conductor can destroy static-sensitive devices or microcircuitry. Often the spark is neither felt nor heard, but damage occurs.

  • Page 68: Personal Grounding Methods And Equipment

    Identifying the Chassis, Routine Care, and Disassembly Preparation 5.2.3 Personal Grounding Methods and Equipment Use the following equipment to prevent static electricity damage to equipment: Wrist straps are flexible straps with a maximum of one-megohm ± 10% resistance in the ground cords.

  • Page 69: Routine Care

    Identifying the Chassis, Routine Care, and Disassembly Preparation Static awareness labels Wrist straps and footwear straps providing one-megohm +/- 10% resistance Material handling packages Conductive plastic bags Conductive plastic tubes Conductive tote boxes Opaque shielding bags Transparent metallized shielding bags Transparent shielding tubes 5.3 Routine Care 5.3.1 General Cleaning Safety Precautions...

  • Page 70: Cleaning The Keyboard

    Identifying the Chassis, Routine Care, and Disassembly Preparation 5.3.3 Cleaning the Keyboard Follow all safety precautions in Section 5.3.1 before cleaning the keyboard. To clean the tops of the keys or the keyboard body, follow the procedures described in Section 5.3.2.

  • Page 71: Service Considerations

    If an incorrect screw is used during the reassembly process, it can damage the unit. HP strongly recommends that all screws removed during disassembly be kept with the part that was removed, then returned to their proper locations.

  • Page 72: Cables And Connectors

    Identifying the Chassis, Routine Care, and Disassembly Preparation 5.4.4 Cables and Connectors Most cables used throughout the unit are flat, flexible cables. These cables must be handled with care to avoid damage. Apply only the tension required to seat or unseat the cables during insertion or removal from the connector.

  • Page 73: Removal And Replacement Procedures - Convertible Minitower (Cmt) Chassis

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. Not all features listed in this guide are available on all computers.

  • Page 74: Unlocking The Smart Cover Lock

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.2 Unlocking the Smart Cover Lock If you have locked the Smart Cover Lock use Computer Setup to unlock the lock. Refer to the Desktop Management Guide on the Documentation Library CD for more information about the Smart Cover Lock.

  • Page 75: Hood Sensor

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.3 Hood Sensor 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the access panel (Section 6.5). 3. Disconnect the hood sensor cable from the system board. 4. Slide the hood sensor switch towards the front of the computer 1 and lower it down through the slot 2.

  • Page 76: External Security Devices

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.4 External Security Devices 6.4.1 Cable Lock The cable lock may be used to secure the computer access panel to the chassis and, at the same time, secure the computer to a fixed object. 6–4 336492-003 Service Reference Guide, d500...

  • Page 77: Padlock

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.4.2 Padlock A padlock may be used by itself to secure the access panel to the computer chassis. A padlock may also be used with a security cable to secure the computer to a fixed object. Service Reference Guide, d500 336492-003 6–5...

  • Page 78: Computer Access Panel

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.5 Computer Access Panel 1. Prepare the computer for disassembly (Section 6.1). Ä CAUTION: Before removing the computer access panel, ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet. 2.

  • Page 79: Front Bezel

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.6 Front Bezel 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3. Push up on the two release tabs 1, then rotate the front bezel away from the chassis to release it 2.

  • Page 80: Front Drive Bezels

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.7 Front Drive Bezels 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the access panel (Section 6.5). 3. Remove the front bezel (Section 6.6). 6.7.1 5.25” Drive Bezel Blank Gently pull the subpanel, with the bezel blanks secured in it, away from the front bezel, then remove the desired bezel blank.

  • Page 81: Diskette Drive Bezel Or Bezel Blank

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.7.2 Diskette Drive Bezel or Bezel Blank Press up on the two small retaining clips 1 on the bottom of the bezel insert, press down on the two small retaining clips 2 on the top of the insert, and push the cover out of the front bezel 3. To install a bezel or a bezel blank, reverse the removal procedure.

  • Page 82: Memory

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.8 Memory CAUTION: The memory module sockets have gold metal contacts. When upgrading the memory, it is important to use memory modules with gold metal contacts to prevent corrosion and/or oxidation resulting from having incompatible metals in contact with each other.
  • Page 83 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis The computer automatically recognizes the additional memory when the computer is turned on. To reassemble the computer, reverse the removal procedure. If you normally lock the Smart Cover Lock, use Computer Setup to relock the lock and enable the Smart Cover Sensor.

  • Page 84: Expansion Cards

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.9 Expansion Cards 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 6.2). 2. Prepare the computer for disassembly (Section 6.1). 3. Remove the computer access panel (Section 6.5). 4.
  • Page 85 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 7. If you are removing an expansion card from a standard expansion socket, hold the card at each end and carefully rock it back and forth until the connectors pull free from the socket. Lift the expansion card straight up to release it from the chassis frame.
  • Page 86 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 8. If you are removing an AGP card from an AGP expansion socket with a retention mechanism, pull the retention arm away from the socket then carefully rock the card back and forth until the connectors pull free from the socket.
  • Page 87 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 11. Slide the bracket on the end of the expansion card down into the slot on the back of the chassis and press the card down firmly into the socket on the system board. When you install an expansion card, make sure you press firmly on the card so that the whole connector seats properly in the expansion card socket on the system board.

  • Page 88: Pci Retainer Latch

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.10 PCI Retainer Latch If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 6.2). 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3.
  • Page 89 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6. Slide the pivoting bar to the right 1 then, lift the left end 2 to remove it from the chassis. To replace the bar, slide it into the socket on the right 1, lower it into position 3, and slide it to the left 4 to secure it in place.

  • Page 90: Drives

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.11 Drives The computer supports up to six drives that may be installed in various configurations. This Section describes the procedure for replacing or upgrading the storage drives. A Torx T-15 screwdriver is needed to remove and install the guide screws on a drive.

  • Page 91: 2Hard Drive

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.11.2 Hard Drive CAUTION: To prevent loss of work and damage to the computer or drive: Ä If you are inserting or removing a hard drive, shut down the operating system properly, then turn off the computer.
  • Page 92 7. Remove the four guide screws (two on each side) from the old drive and install them in the replacement drive. Extra guide screws are provided on the chassis on the side of the fourth drive bay. Optical drives use M3 metric screws. The HP-supplied metric screws are black. The HP-supplied standard screws are silver. 6–20...
  • Page 93 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 8. Store the removed drive in anti-static packaging. 9. Install the new drive by sliding it into the appropriate drive bay on the front of the chassis. The drivelock automatically secures the drive in the bay. Service Reference Guide, d500 336492-003 6–21...

  • Page 94: 3Optical Drive

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.11.3 Optical Drive An optical drive is a CD-ROM, CD-R/RW, DVD-ROM, DVD-R/RW, or CD-RW/DVD Combo drive. A removable storage drive is a diskette or Zip drive. 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 6.2).
  • Page 95 Extra guide screws are provided on the chassis on the side of the fourth drive bay. Optical drives use M3 metric screws. The HP-supplied metric screws are black. The HP-supplied standard screws are silver.
  • Page 96 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 10. Install the drive by sliding it into the appropriate drive bay on the front of the chassis. The drivelock automatically secures the drive in the bay. CAUTION: Make sure the guide screws line up with the guide slots in the drive cage. The use of Ä...

  • Page 97: 4Diskette Drive

    Install four guide screws, two on each side of the drive. Extra guide screws are provided on the side of the drive bay under the access panel. The diskette drive use M3 metric screws. The HP-supplied metric screws are black. The HP-supplied standard screws are silver.

  • Page 98: Front I/O Device

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.12 Front I/O Device 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3. Disconnect the two I/O device cables from the system board: the front USB cable pair and the front audio cable.

  • Page 99: Power Switch Assembly

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.13 Power Switch Assembly 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3. Disconnect the power switch/LED cable from the system board. 4. Squeeze the switch holder retaining clips together at the front of the chassis 1 and push the switch assembly out of the chassis 2.

  • Page 100: System Board

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.14 System Board 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3. Remove all PCI expansion boards (Section 6.9). 4. Remove the AGP graphics card (Section 6.9). 5.

  • Page 101: Battery

    Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP/Compaq, their authorized partners, or their agents. Ä...

  • Page 102: 1Type 1 Battery Holder

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.15.1 Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacement battery into position, positive side up. 3. The battery holder automatically secures the battery in the proper position. 4.

  • Page 103: 2Type 2 Battery Holder

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.15.2 Type 2 Battery Holder 1. To release the battery from its holder, squeeze the metal clamp 1 that extends above one edge of the battery. When the battery pops up, lift it out. 2.

  • Page 104: Processor And Heatsink

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.16 Processor and Heatsink There are three different heatsinks that may be used on this model of computer. While the components differ from unit to unit, they all require similar steps. 1.

  • Page 105: Type 2

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.16.2 Type 2 1. Release the tension from the heatsink 1 and 2. 2. Remove the retaining clips 3. 3. Remove the heatsink from atop the processor 4. 4. Open the ZIF socket lever 5. 5.

  • Page 106: Type 3

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.16.3 Type 3 1. Release the tension from the heatsink 1. 2. Remove the retaining clips 2. 3. Remove the heatsink from atop the processor 3. 4. Open the ZIF socket lever 4. 5.

  • Page 107: Speaker

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.17 Speaker 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3. Disconnect the speaker wire from the system board. 4. Remove the four screws from the inside of the chassis 1 that secure the speaker to the chassis.

  • Page 108: Chassis Fan

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.18 Chassis Fan 1. Prepare the computer for disassembly (Section 6.1). 2. Remove the computer access panel (Section 6.5). 3. Disconnect the fan control cable from the system board. 4. Remove the four screws that secure the fan assembly to the chassis 1 and then remove the fan assembly 2.

  • Page 109: Power Supply

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.19 Power Supply Å WARNING: Voltage is always present on the system board when the computer is plugged into an active AC outlet. To avoid possible personal injury and damage to the equipment the power cord should be disconnected from the computer and/or the AC outlet before opening the computer.

  • Page 110: Changing From Desktop To Minitower

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.20 Changing from Desktop to Minitower 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock it. 2. Prepare the computer for disassembly (Section 6.1). 3. Remove the computer access panel (Section 6.5). 4.
  • Page 111 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 7. Before you reinstall each drive into the chassis, turn it so that it is in the same orientation as the internal 3.5-inch drive. The bottom of the drive should be parallel to the yellow drivelock.
  • Page 112 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 12. Reposition the subpanel (rotate it 180°) with the logo at the bottom, then snap it back into the bezel. 6–40 336492-003 Service Reference Guide, d500...

  • Page 113: Changing From Minitower To Desktop

    Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6.21 Changing from Minitower to Desktop 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock it. 2. Prepare the computer for disassembly (Section 6.1). 3. Remove the computer access panel (Section 6.5). 4.
  • Page 114 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 7. Before reinstalling each drive into the chassis, turn the drive so that it is perpendicular to the internal 3.5-inch drive. The drive should be parallel to the green latch drive bracket. 8.
  • Page 115 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 12. Reposition the subpanel (rotate it 180°) with the logo at the bottom, then snap it back into the bezel. 13. Replace the front bezel and computer access panel. 14. Reconnect the external equipment. 15.
  • Page 116 Removal and Replacement Procedures - Convertible Minitower (CMT) Chassis 6–44 336492-003 Service Reference Guide, d500...

  • Page 117: Removal And Replacement Procedures - Small Form Factor (Sff) Chassis

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. Not all features listed in this guide are available on all computers.

  • Page 118: Unlocking The Smart Cover Lock

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Unlocking the Smart Cover Lock If you have locked the Smart Cover Lock use Computer Setup to unlock the lock. Refer to the Desktop Management Guide on the Documentation Library CD for more information about the Smart Cover Lock.

  • Page 119: Hood Sensor

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Hood Sensor 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Remove the front bezel (Section 7.6). 4. Raise the drive cage to its upright position 1. 5.

  • Page 120: External Security Devices

    As shown, there are two acceptable methods for using the cable lock. While both methods work, for added security HP recommends that you use the method shown on the left where the cable lock penetrates both the access panel and the chassis.

  • Page 121: Padlock

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.4.2 Padlock A padlock may be used by itself to secure the access panel to the computer chassis. A padlock may also be used with a security cable to secure the computer to a fixed object. Service Reference Guide, d500 336492-003 7–5...

  • Page 122: Computer Access Panel

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Computer Access Panel 1. Prepare the computer for disassembly (Section 7.1). Ä CAUTION: Before removing the computer access panel, ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet. 2.

  • Page 123: Front Bezel

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Front Bezel 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Pull up on the three release tabs 1 on the top of the bezel, then pull the front bezel away from the chassis 2.

  • Page 124: Front Drive Bezels

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Front Drive Bezels 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Remove the front bezel (Section 7.6). 7.7.1 Diskette Drive Bezel or Bezel Blank Press the large retaining tab 1 on the left side of the bezel insert to the left and push the cover out of the front bezel 2.

  • Page 125: Memory

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Memory Ä CAUTION: The memory module sockets have gold metal contacts. When upgrading the memory, it is important to use memory modules with gold metal contacts to prevent corrosion and/or oxidation resulting from having incompatible metals in contact with each other.
  • Page 126 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis The computer automatically recognizes the additional memory when the computer is turned on. To reassemble the computer, reverse the removal procedure. If you normally lock the Smart Cover Lock, use Computer Setup to relock the lock and enable the Smart Cover Sensor.

  • Page 127: Expansion Card Cage

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis Expansion Card Cage 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 7.2). 2. Prepare the computer for disassembly (Section 7.1). 3. Remove the computer access panel (Section 7.5). 4.

  • Page 128: Riser Card

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.9.1 Riser Card 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 7.2). 2. Prepare the computer for disassembly (Section 7.1). 3. Remove the computer access panel (Section 7.5). 4.

  • Page 129: Expansion Card

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.9.2 Expansion Card 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 7.2). 2. Prepare the computer for disassembly (Section 7.1). 3. Remove the computer access panel (Section 7.5). 4.
  • Page 130 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 8. To remove an expansion card, hold the card at each end and carefully rock it back and forth until the connectors pull free from the socket. Lift the expansion card straight up to release it from the carrier.

  • Page 131: Agp Card

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.9.3 AGP Card 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 7.2). 2. Prepare the computer for disassembly (Section 7.1). 3. Remove the computer access panel (Section 7.5). 4.
  • Page 132 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 11. Connect external cables to the installed card and internal cables to the system board as needed. 12. Replace the computer cover. 13. If you normally lock the Smart Cover Lock, use Computer Setup to relock the lock and enable the Smart Cover Sensor.

  • Page 133: Drives

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.10 Drives The computer supports up to three drives. This Section describes the procedure for replacing or upgrading the storage drives. A Torx T-15 screwdriver is needed to remove and install the guide screws on a drive. Ä...

  • Page 134: 2Cable Routing

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.10.2 Cable Routing CAUTION: The drive data and power cables must be kept clear of the power supply and the power Ä supply fan to avoid damage or restrict air flow. Follow these guidelines when routing the cables in the computer: 1.

  • Page 135: 3Optical Drive

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.10.3 Optical Drive CAUTION: All removable media should be taken out of the drives before removing the drive from the Ä computer. An optical drive is a CD-ROM, CD-RW, or DVD-ROM drive. 1.
  • Page 136 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis When replacing the drive, transfer the four screws from the old drive to the new one. The screws take the place of drive rails. 2. Position the guide screws on the drive into the J-slots in the drive bay 1. Then, slide the drive towards the rear of the computer 2.
  • Page 137 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 3. Raise the Easy Access drive bay to the upright position and connect the flat ribbon cable and audio cable to the system board. 4. Connect the power cable, flat ribbon cable, and audio cable to the rear of the optical drive. 5.

  • Page 138: 4External 3.5-Inch Drive

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.10.4 External 3.5-inch Drive 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 7.2). 2. Prepare the computer for disassembly (Section 7.1). 3.
  • Page 139 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis The guide screws on a 3.5-inch diskette drive 1 are placed closer together than on the hard drive 2. 11. Insert the rear screws of the hard drive 1 into the rear J-slots. Slide the drive 2 toward the back of the drive cage until the front screws are aligned with the front J-slots.
  • Page 140 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 14. If the drive cage was raised to gain access to the drive cables, lower it to its original position at this time. 15. Replace the front bezel and computer access panel. 7–24 336492-003 Service Reference Guide, d500...

  • Page 141: 5Primary Hard Drive

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.10.5 Primary Hard Drive 1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (Section 7.2). 2. Prepare the computer for disassembly (Section 7.1). 3.
  • Page 142 Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7. Press and hold the drive release latch 1. 8. Slide the drive to the right of the bay 2, then pull the drive from the bay 3. To replace the hard drive, reverse the above procedure. Make sure you position all cable correctly before returning the drive cage to its original position (Section 7.10.2).

  • Page 143: Front I/O Devices

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.11 Front I/O Devices 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Disconnect the two I/O device cables from the system board: the front USB cable pair and the front audio cable.

  • Page 144: Power Switch Assembly

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.12 Power Switch Assembly 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Disconnect the power switch/LED cable from the system board. 4.

  • Page 145: System Board

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.13 System Board 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Remove all PCI expansion boards (Section 7.9). 4. Remove the AGP graphics card (Section 7.9). 5.

  • Page 146: Chassis Fan

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.14 Chassis Fan 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Remove the system board (Section 7.13). 4. Remove the chassis fan cable from the wiring harness and from cable clip 1 near the front of the chassis.

  • Page 147: Battery

    Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP/Compaq, their authorized partners, or their agents. Ä...

  • Page 148: 1Type 1 Battery Holder

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.15.1 Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacement battery into position, positive side up. 3. The battery holder automatically secures the battery in the proper position. 4.

  • Page 149: 2Type 2 Battery Holder

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.15.2 Type 2 Battery Holder 1. To release the battery from its holder, squeeze the metal clamp that extends above one edge of the battery. When the battery pops up, lift it out 1. 2.

  • Page 150: Processor And Heatsink

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.16 Processor and Heatsink 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Lift up the lever that secure the fan to the heatsink 1 and rotate the fan up 2. 4.

  • Page 151: Speaker

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.17 Speaker 1. Prepare the computer for disassembly (Section 7.1). 2. Remove the computer access panel (Section 7.5). 3. Rotate the drive cage to its upright position. 4. Remove the expansion card cage (Section 7.9). 5.

  • Page 152: Power Supply

    Removal and Replacement Procedures - Small Form Factor (SFF) Chassis 7.18 Power Supply Å WARNING: Voltage is always present on the system board when the computer is plugged into an active AC outlet. To avoid possible personal injury and damage to the equipment the power cord should be disconnected from the computer and/or the AC outlet before opening the computer.

  • Page 153: Removal And Replacement Procedures - Ultra-Slim Desktop (Usdt) Chassis

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. Not all features listed in this guide are available on all computers.
  • Page 154 Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8. If the PC is mounted in the accessory mounting stand, remove it and lay the computer down on its rubber feet. 8–2 336492-003 Service Reference Guide...

  • Page 155: External Security Devices

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.2 External Security Devices 8.2.1 Installing a Cable Lock The cable lock may be used to secure the computer access panel to the chassis and, at the same time, secure the computer to a fixed object. Service Reference Guide 336492-003 8–3...

  • Page 156: Installing A Padlock

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.2.2 Installing a Padlock A padlock may be used by itself to secure the access panel to the computer chassis. A padlock may also be used with a security cable to secure the computer to a fixed object. 8–4 336492-003 Service Reference Guide...

  • Page 157: Computer Access Panel

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.3 Computer Access Panel Remove the bottom access panel to remove or replace and expansion card. Remove the top access panel for all other service activities. 8.3.1 Top Access Panel 1. Prepare the computer for disassembly (Section 8.1). CAUTION: Before removing the computer access panel, ensure that the computer is turned off and that Ä...

  • Page 158: Bottom Access Panel

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.3.2 Bottom Access Panel 1. Prepare the computer for disassembly (Section 8.1). CAUTION: Before removing the computer access panel, ensure that the computer is turned off and that Ä the power cord is disconnected from the electrical outlet. 2.

  • Page 159: Front Bezel

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.4 Front Bezel 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer access panel (Section 8.3). 3. Press the two release tabs on the right side of the bezel 1, then rotate the front bezel away from the chassis to release it 2.

  • Page 160: Memory

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.5 Memory Ä CAUTION: The memory module sockets have gold metal contacts. When upgrading the memory, it is important to use memory modules with gold metal contacts to prevent corrosion and/or oxidation resulting from having incompatible metals in contact with each other.
  • Page 161 Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis The computer automatically recognizes the additional memory when the computer is turned on. To reassemble the computer, reverse the removal procedure. Service Reference Guide 336492-003 8–9...

  • Page 162: Expansion Cards

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.6 Expansion Cards 1. Prepare the computer for disassembly (Section 8.1). 2. Lay the computer down on a flat surface with the rubber feet facing up. 3. Remove the bottom access panel (Section 8.3.2). 4.
  • Page 163 Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 7. Slide the bracket on the end of the expansion card down into the slot 1 and press the card firmly into the socket. When you install an expansion card, make sure you press firmly on the card so that the whole connector seats properly in the expansion card socket on the system board.

  • Page 164: Expansion Card Locking Lever

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.7 Expansion Card Locking Lever 1. Prepare the computer for disassembly (Section 8.1). 2. Lay the computer down on a flat surface with the rubber feet facing up. 3. Remove the bottom access panel (Section 8.3.2). 4.

  • Page 165: Drives

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.8 Drives This computer supports a single hard drive and a single MultiBay drive. A Torx T-15 screwdriver is needed to remove and install the guide screws on a hard drive. Ä...
  • Page 166 Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 4. Disconnect the data and power cables from the back of the drive 5. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive.

  • Page 167: Multibay Drive

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.8.2 MultiBay Drive 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the top access panel (Section 8.3.1). It is only necessary to remove the top access panel if the MultiBay security catch is engaged. 3.
  • Page 168 Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 4. Pull the eject lever towards the front of the computer 1 to eject the drive from the MultiBay 2. To install a MultiBay drive, reverse the removal procedures. It is not necessary to remove the top access panel if you do not want to engage the drive security lock.

  • Page 169: System Fan

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.9 System Fan 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the top access panel (Section 8.3.1). 3. Spread the two clips that secure the fan housing in place 1, then lift the housing from the chassis 2.

  • Page 170: Front Chassis Panel

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.10 Front Chassis Panel Removing the front chassis panel makes it easier to remove the front I/O device and the power/LED switch assembly. 1. Prepare the computer for disassembly (Section 8.1). 2.

  • Page 171: Front I/O Device

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.11 Front I/O Device 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the system fan (Section 8.9). 4. Remove the front chassis panel (Section 8.10). Removing the front chassis panel makes it easier to access the cable connectors on the system board.

  • Page 172: Power Switch Assembly

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.12 Power Switch Assembly 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the system fan (Section 8.9). 4. Remove the front chassis panel (Section 8.10). Removing the front chassis panel makes it easier to access the cable connectors on the system board.

  • Page 173: Processor And Heatsink

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.13 Processor and Heatsink 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the system fan (Section 8.9). 4. Tap the heatsink to check its temperature. If it is cool enough to handle, then proceed. 5.

  • Page 174: Power Supply

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.14 Power Supply Å WARNING: Voltage is always present on the system board when the computer is plugged into an active AC outlet. To avoid possible personal injury and damage to the equipment the power cord should be disconnected from the computer and/or the AC outlet before opening the computer.

  • Page 175: Battery

    Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP/Compaq, their authorized partners, or their agents. Ä...

  • Page 176: 1Type 1 Battery Holder

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.15.1 Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacement battery into position, positive side up. 3. The battery holder automatically secures the battery in the proper position. 4.

  • Page 177: 2Type 2 Battery Holder

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.15.2 Type 2 Battery Holder 1. To release the battery from its holder, squeeze the metal clamp 1 that extends above one edge of the battery. When the battery pops up, lift it out. 2.

  • Page 178: Drive Cage Assembly

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.16 Drive Cage Assembly 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the hard drive (Section 8.8.1). 4. Remove the system fan (Section 8.9). 5.

  • Page 179: Speaker

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.17 Speaker 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the hard drive (Section 8.8). 4. Remove the system fan (Section 8.9). 5.

  • Page 180: Chassis Fan

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.18 Chassis Fan 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the hard drive (Section 8.8.1). 4. Remove the system fan (Section 8.9). 5.

  • Page 181: System Board

    Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8.19 System Board 1. Prepare the computer for disassembly (Section 8.1). 2. Remove the computer top access panel (Section 8.3.1). 3. Remove the memory modules (Section 8.5). 4. Remove the hard drive (Section 8.8.1). 5.
  • Page 182 Removal and Replacement Procedures - Ultra-Slim Desktop (USDT) Chassis 8–30 336492-003 Service Reference Guide...

  • Page 183: Connector Pin Assignments

    Connector Pin Assignments This appendix contains the pin assignments for many computer and workstation connectors. Some of these connectors may not be used on the product being serviced. Enhanced Keyboard Connector and Icon Signal Data Unused Ground +5 VDC Clock Unused Mouse Connector and Icon...

  • Page 184: Ethernet Aui

    Connector Pin Assignments Ethernet RJ-45 Connector and Icon Signal (+) Transmit Data (-) Transmit Data (+) Receive Data Unused Unused (-) Receive Data Unused Unused Ethernet AUI Connector and Icon Signal Signal Ground Positive AUI Differential Receive Negative AUI Differential Collision +12V Positive AUI Differential Collision Ground...

  • Page 185: Parallel Interface

    Connector Pin Assignments Parallel Interface Connector and Icon Signal Signal Signal Strobe Data Bit 5 Select Data Bit 0 Data Bit 6 Auto Linefeed Data Bit 1 Data Bit 7 Error Data Bit 2 Acknowledge Initialize Printer Data Bit 3 Busy Select IN Data Bit 4...
  • Page 186 Connector Pin Assignments Headphone Connector and Icon (1/8” miniphone) Signal 1 (Tip) Audio_Left 1 2 3 2 (Ring) Audio_Right 3 (Shield) Ground Line-In Audio Connector and Icon (1/8” miniphone) Signal 1 (Tip) Audio_In_Left 1 2 3 2 (Ring) Audio_In_Right 3 (Shield) Ground Line-Out Audio Connector and Icon (1/8”...

  • Page 187: External Infrared Transceiver

    Connector Pin Assignments Ultra SCSI Connector and Icon Signal Signal Signal Signal 1-11 Ground Reserved RST # Reserved TERMPWR MSG # Open Reserved SEL # Reserved Ground 15-25 Ground ATN # REQ # Ground Input/Output Ground BSY # Ground ACK # External Infrared Transceiver Connector and Icon Signal...
  • Page 188 Connector Pin Assignments ATA/ATAPI (IDE) Standard Drive Cable Connector Signal Signal Signal Reset DMAK Ground DD14 Ground INTRQ DD15 IOCS16 Ground (Key) PDIAG (cable detect) DMARQ DD10 Ground DIOW CS1FX DD11 Ground CS3FX DIOR DASP DD12 Ground Ground IORDY DD13 CSEL MultiBay CD-ROM Adapter Connector...
  • Page 189 Connector Pin Assignments Accelerated Graphics Port (AGP) Connector Signal A Signal B Signal A Signal B +12 V OVRCNT# Vddq Vddq TYPEDET# + 5V AD22 AD21 Reserved + 5V AD20 AD19 USB- USB+ Ground Ground Ground Ground AD18 AD17 INTA# INTB# AD16 C/BE2#...

  • Page 190: Pin Power

    Connector Pin Assignments 20-Pin Power Connector Signal Signal Signal Signal +3.3 V +5 V +3.3 V +3.3 V -12 V open* +5 V +5 Vaux PSON +5 V +12 V +5 V *Open for d300 series computers; -5V for all others 4-Pin Power (for CPU) Connector and Icon Signal...

  • Page 191: B Power Cord Set Requirements

    Power cord sets for use in other countries must meet the requirements of the country where you use the computer. For more information on power cord set requirements, contact your authorized HP dealer, reseller, or service provider. General Requirements The requirements listed below are applicable to all countries: 1.
  • Page 192 Country-Specific Requirements Additional requirements specific to a country are shown in parentheses and explained below. Accrediting Accrediting Country Agency Country Agency Australia (1) EANSW Italy (1) Austria (1) Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) Sweden (1) SEMKO Denmark (1) DEMKO...

  • Page 193: Post Error Messages

    POST Error Messages An error message results if the Power-On Self-Test (POST) encounters a problem. This test runs when the system is turned on, checking assemblies within the computer and reporting any errors found. Not all computers use all of the codes listed. POST Error Messages Screen Message Probable Cause...
  • Page 194 Windows utilities. Make sure memory module(s) (if any) are installed properly. If third party memory has been added, test using HP-only memory. Verify proper memory module type. 183-Invalid Processor System board jumper Reset system board jumpers to match Jumper Setting improperly set.
  • Page 195 POST Error Messages Screen Message Probable Cause Recommended Action 214-DIMM Populated DIMM 2 DIMMS - For maximum performance, Configuration Warning Configuration is place both DIMMs in the two BLACK unbalanced. DIMM slots. 4 DIMMS - For maximum performance, swap one DIMM in a BLUE slot with one in a BLACK slot.
  • Page 196 POST Error Messages Screen Message Probable Cause Recommended Action 501-Display Adapter Graphics display Reseat the graphics card (if applicable). Failure controller. Clear CMOS. Verify that the monitor is attached and turned on. Replace the graphics controller. 510-Splash Screen Splash Screen image has Install latest version of ROMPaq to image corrupted errors.
  • Page 197 POST Error Messages Screen Message Probable Cause Recommended Action 660-Display Cache is Integrated video Replace system board if minimal video Detected Unreliable controller display cache degrading is an issue. not working properly and will be disabled. 912-Computer Cover No action required. Has Been Removed Since Last System Start 914-Hood Lock Coil is...
  • Page 198 System text if applicable. that will fix an erroneous Apply firmware patch if applicable. (see error message.) www.hp.com/support) Back up contents and replace hard drive. 1794-Inaccessible Devices attached to the If you do not require access to SATA...
  • Page 199 Number. has become corrupted. has data in the field or will not allow the serial number to be entered, download from http://www.hp.com and run SP5572.EXE (SNZERO.EXE). Run Computer Setup and try to enter serial number under Security, System ID, then save changes.
  • Page 200 C–8 336492-003 Service Reference Guide, d500...

  • Page 201: Preliminary Checklist

    Troubleshooting Without Diagnostics Preliminary Checklist This section describes some simple, preliminary tests and guidelines for troubleshooting the computer without using the diagnostics. Are the computer and monitor connected to a working electrical outlet? Is the voltage select switch is set to the appropriate voltage for your region (115V or 230V)? Is the computer turned on? Is the green power light illuminated? Is the monitor turned on?

  • Page 202: Solving Minor Problems

    Solving Minor Problems Solving Minor Problems Problem Cause Possible Solution Computer appears Software control of the 1. Press and hold the power button locked up and will not power switch is not for at least four seconds until the turn off when the power functional.
  • Page 203 Solving Minor Problems (Continued) Problem Cause Possible Solution Computer powered off Processor thermal 1. Ensure computer air vents are not automatically and the protection activated: blocked and the cooling fan is Power LED flashes Red running. A fan may be blocked or two times, once every not turning.

  • Page 204: Solving Power Supply Problems

    Solving Power Supply Problems Solving Power Supply Problems Problem Cause Solution Power supply shuts down Voltage selector switch Select the proper AC voltage. intermittently. on rear of computer chassis not switched to correct line voltage. Power supply fault. Replace the power supply. Computer powered off Processor thermal 1.

  • Page 205: Solving Diskette Problems

    Solving Diskette Problems Solving Diskette Problems Problem Cause Solution Diskette drive light stays on. Diskette is damaged. In Microsoft Windows 2000 and Microsoft Windows XP, right-click Start, click Explore, and select a drive. Select File > Properties > Tools. Under Error-checking, click Check Now.
  • Page 206 Solving Diskette Problems (Continued) Problem Cause Solution Cannot format diskette. Invalid media reported. When formatting a disk in MS-DOS, you may need to specify diskette capacity. For example, to format a 1.44-MB diskette, type the following command at the MS-DOS prompt: FORMAT A: /F:1440 A problem has occurred The directory structure is...

  • Page 207: Solving Hard Drive Problems

    Solving Hard Drive Problems Solving Hard Drive Problems Problem Cause Solution Hard drive error occurs. Hard disk has bad Use a utility to locate and block sectors or has failed. usage of bad sectors. If necessary, reformat the hard disk. Disk transaction problem.
  • Page 208 Solving Hard Drive Problems (Continued) Problem Cause Solution Nonsystem disk/NTLDR System is trying to start 1. Insert a bootable diskette into missing message. from a damaged hard the diskette drive and restart the (continued) drive. computer. 2. If the hard drive is still inaccessible and MBR Security is enabled, try restoring the previously saved MBR image by...

  • Page 209: Solving Display Problems

    Solving Display Problems Solving Display Problems Problem Cause Solution Blank screen (no video). The cable connections Check the cable connections from are not correct. the monitor to the computer and to the electrical outlet. Screen blanking utility Press any key or click the mouse installed or energy button and, if set, type your saver features enabled.
  • Page 210 Solving Display Problems (Continued) Problem Cause Solution Power LED flashes Red six Pre-video graphics For systems with a graphics card: times, once every second, error. 1. Reseat the graphics card. followed by a two second 2. Replace the graphics card. pause, and the computer beeps six times.
  • Page 211 Solving Display Problems (Continued) Problem Cause Solution High pitched noise coming Brightness and/or Lower brightness and/or contrast from inside a flat panel contrast settings are too settings. monitor. high. Fuzzy focus; streaking, Flat panel monitor’s 1. Select the monitor’s ghosting, or shadowing internal digital Auto-Adjustment option in the effects;...

  • Page 212: Solving Audio Problems

    Solving Audio Problems Solving Audio Problems Problem Cause Solution Sound does not come Software volume control Double-click the Speaker icon on out of the speaker or is turned down. the taskbar and use the volume headphones. slider to adjust the volume. The external speakers Turn on the external speakers.
  • Page 213 Solving Audio Problems (Continued) Problem Cause Solution Noise or no sound comes 1. If using digital speakers that out of the speakers or have a stereo jack and want the headphones. system to auto-switch to digital, use a stereo-to-mono adapter to properly engage the auto-sense feature or use the multimedia device properties...

  • Page 214: Solving Printer Problems

    Solving Printer Problems Solving Printer Problems Problem Cause Solution Printer will not print. Printer is not turned on Turn the printer on and make sure it and online. is online. The correct printer 1. Install the correct printer driver driver for the for the application.

  • Page 215: Solving Keyboard And Mouse Problems

    Solving Keyboard and Mouse Problems Solving Keyboard Problems Problem Cause Solution Keyboard commands and Keyboard connector 1. Turn off the computer. typing are not recognized is not properly 2. Reconnect the keyboard to the by the computer. connected. back of the computer and restart the computer.

  • Page 216: Solving Hardware Installation Problems

    Solving Hardware Installation Problems You may need to reconfigure the computer when you add or remove hardware, such as an additional diskette drive. If you install a plug and play device, Windows 2000 and Windows XP automatically recognize the device and configure the computer. If you install a non–plug and play device, you must reconfigure the computer after completing installation of the new hardware.
  • Page 217 3. Replace third-party memory beeps five times. with HP memory. 4. Replace the system board. Power LED flashes Red six Video card is not seated For systems with a graphics card:...

  • Page 218: Solving Network Problems

    Solving Network Problems These guidelines do not discuss the process of debugging the network cabling. Solving Network Problems Problem Cause Solution Wake-on-LAN feature is Wake-on-LAN is not Use the Network control not functioning. enabled. application to enable Wake-on-LAN. Network driver does Network controller is Run Computer Setup and enable not detect network...
  • Page 219 Solving Network Problems (Continued) Problem Cause Solution Select the Network icon in the Diagnostics passes, but The network controller the computer does not is not configured for this Control Panel and configure the communicate with the computer. network controller. network. (continued) Network controller Network controller Under the Computer Setup...

  • Page 220: Solving Memory Problems

    Solving Memory Problems CAUTION: For those systems that support ECC memory, HP does not support mixing ECC and non-ECC Ä memory. Otherwise, the system will not boot the operating system. Solving Memory Problems Problem Cause Solution System will not boot or...

  • Page 221: Solving Processor Problems

    Solving Processor Problems Solving Processor Problems Problem Cause Solution Poor performance is Processor is hot. 1. Make sure the airflow to the experienced. computer is not blocked. 2. Make sure the fans are connected and working properly (some fans only operate when needed).

  • Page 222: Solving Cd-Rom And Dvd Problems

    Solving CD-ROM and DVD Problems Solving CD-ROM and DVD Problems Problem Cause Solution System will not boot from The CD-ROM or DVD Run the Computer Setup utility and CD-ROM or DVD drive. boot is not enabled enable booting to removable media through the Computer and verify boot order settings.

  • Page 223: Solving Drive Key Problems

    Solving CD-ROM and DVD Problems (Continued) Problem Cause Solution Recording audio CDs is Wrong or poor quality 1. Try using a slower recording difficult or impossible. media type. speed. 2. Verify that you are using the correct media for the drive. 3.
  • Page 224 Solving Internet Access Problems (Continued) Problem Cause Solution Unable to connect to the Cable/DSL service is Try connecting to the Internet at a Internet. (continued) not available or has later time or contact your ISP. (If the been interrupted due to cable/DSL service is connected, the bad weather.
  • Page 225 Solving Internet Access Problems (Continued) Problem Cause Solution Internet takes too long to Modem is not set up Verify that the correct modem speed download Web sites. properly. and COM port are selected. For Windows 2000 1. Select Start > Settings > Control Panel.
  • Page 226 D–26 336492-003 Service Reference Guide, d500...
  • Page 227 System Board and Riser Board Reference Designators These reference designators are used on most but not all hp system and riser boards. Designator Component Battery socket/Battery LED - 3.3V Aux LED - Power button press LED - PS_ON (off), 5.5V Aux (on)
  • Page 228 Designator Component (Continued) Double-stacked mouse/keyboard connector Mouse Bottom Keyboard Video connector Primary single USB connector Secondary single USB jack Microphone jack Line-in jack Line-out jack Headphone jack Volume control Double-stacked headphone/microphone connector Top Microphone Bottom Headphone Double-stacked line-in/line-out connector Top Line in Bottom Line out Stacked serial/audio connector Primary double-stack USB...
  • Page 229 Designator Component (Continued) Slimline CD-ROM connector Header for front audio panel Header for front panel USB P25 - P26 Video memory upgrade connector MultiBay header SCSI LED connector Primary serial ATA (SATA) port Secondary serial ATA (SATA) port Serial debug header Serial port header First serial port Second serial port...
  • Page 230 E–4 336492-003 Service Reference Guide, d500...
  • Page 231 Memory AMD-Based Systems Computers equipped with AMD-based processors come with Double Data Rate-Synchronous Dynamic Random Access Memory (DDR-SDRAM) Dual Inline Memory Modules (DIMMs). The memory sockets on the system board can be populated with industry-standard DIMMs. These memory module slots are populated with at least one pre installed memory module. To achieve the maximum memory support, you may be required to replace the pre installed DIMM with a higher capacity DIMM.

  • Page 232: Dimm Sockets

    The following processor bus frequencies are required for the system to run at the supported memory frequencies. Memory Frequency Required Processor Bus Frequency 266 MHz 400 MHz, 533 MHz, or 800 MHz 333 MHz 533 MHz or 800 MHz 400 MHz 800 MHz If a memory frequency is paired with an unsupported processor bus frequency, the system will run at the highest supported memory speed.
  • Page 233 The system will automatically operate in single channel mode or a higher-performing dual channel mode, depending on how the DIMMs are installed. In single channel mode, the maximum operational speed is determined by the slowest DIMM in the system. For example, if the system is populated with a DIMM that is 266 MHz and a second DIMM that is 333 MHz, the system will run at the slower of the two speeds.
  • Page 234 F–4 336492-003 Service Reference Guide, d500...
  • Page 235 Index Index 4-pin power pin assignments A–8 batteries 5–8 24-pin power pin assignments A–8 cables 5–8 cooling fan 5–7 installation 1–1 access panel keyboard cleaning 5–6 bottom, USDT removal and replacement 8–6 keyboard keys 5–6 CMT removal and replacement 6–6 chassis top, USDT removal and replacement 8–5 CMT illustrated 5–1...
  • Page 236 Index hood sensor removal and replacement 6–3 diskette drive bezel memory removal and replacement 6–10 CMT removal and replacement 6–9 minitower to desktop conversion 6–41 SFF removal and replacement 7–8 padlock 6–5 drive PCI retainer latch removal and replacement cable select 4–1 6–16 capacities 4–9 power supply removal and replacement 6–37...
  • Page 237 SFF 7–5 CMT removal and replacement 6–3 USDT 8–4 SFF removal and replacement 7–3 parallel interface pin assignments A–3 HP software. See software password power-on 2–1 PATA cable layout 4–3 infrared (IR) transceiver, external, pin assignments PATA data cable pinouts 4–2 A–5...
  • Page 238 Index display D–9 SFF expansion slot cover 7–13 drive key D–23 SFF external 3.5-inch drive 7–22 hard drive D–7 SFF front bezel 7–7 installing hardware D–16 SFF front drive bezel 7–8 Internet access D–23 SFF front I/O devices 7–27 keyboard D–15 SFF hard drive 7–25 memory D–20 SFF heatsink 7–34...
  • Page 239 Index screws, correct size 5–7 tamper-proof screws 7–2 SCSI Small Form Factor. See SFF pin assignments A–4 Smart Cover Lock SDRAM (synchronous dynamic random access CMT 6–2 memory) F–1 SFF 7–2 security software CMT 6–4 Computer Setup Utilities 2–1 Computer Setup heading 2–7 protecting 2–18 SFF 7–4 required 5–7...
  • Page 240 Index front bezel removal and replacement 8–7 system fan removal and replacement 8–17 front I/O devices removal and replacement 8–19 top access panel hard drive removal and replacement 8–13 removal and replacement 8–5 heatsink removal and replacement 8–21 USDT access panel lower air flow guide removaland replacement removal and replacement 8–5 8–21...

Table of Contents