Table of Contents
Advertisement
Quick Links
GAS COOKTOP
INSTALLATION INSTRUCTIONS
Please read this guide thoroughly
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
Installation of this cooktop must conform with local
codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA.54,
latest edition. In Canada, installation must
conform with the current Natural Gas Installation
Code, CAN/CGAB149.1 or the current Propane
Installation Code, CAN/CGA-B149.2, and with
local codes where applicable. This cooktop has
been design-certified by CSA International
according to ANSI Z21.1, latest edition and
Canadian Gas Association according to
CAN/CGA-1.1 latest edition.
As with any appliance using gas and generating
heat, there are certain safety precautions you
should follow. You will find these precautions in
the Important Safety Information section in your
User's Guide. Read them carefully.
• IMPORTANT
for local electrical inspector's use.
• IMPORTANT
codes and ordinances.
P/No.: MFL62725501
before installation.
– Save these instructions
– Observe all governing
To contact LG Electronics, 24 hours a day,
7 days a week:
1-800-243-0000 (U.S.A.)
1-888-542-2623 (Canada)
Or visit us on the Web at:
us.lge.com (U.S.A.)
ca.lge.com (Canada)
Note to Installer: Leave these instructions with
the appliance after installation is completed.
Note to Consumer: Keep the User's Guide and
Installation Instructions for future reference.
NOTE: This appliance must be properly
grounded.
• The electrical diagram is in an envelope
attached to the back of the cooktop.
• Skill level – Installation of this appliance
requires basic mechanical skills.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is
not covered under the Warranty.
• Remove all tape and packaging.
• Make sure the burners are properly seated
and level.
• Take the accessory pack off of the cooktop.
• Check to be sure that no cooktop parts have
come loose during shipping.
Advertisement
Table of Contents
Related Manuals for LG MFL62725501
Summary of Contents for LG MFL62725501
-
Page 1: Gas Cooktop
• Take the accessory pack off of the cooktop. • Check to be sure that no cooktop parts have come loose during shipping. To contact LG Electronics, 24 hours a day, 7 days a week: 1-800-243-0000 (U.S.A.) 1-888-542-2623 (Canada) Or visit us on the Web at: us.lge.com (U.S.A.) -
Page 2: Installation Instructions
(one for support) (one for support) line (3/4” or 1/2” NPT x 5/8” I.D.) • Flare union adapter for connection to pressure regulator on cooktop. (1/4” NPT x 1/2” I.D.) • Liquid leak detector or soapy water. Shut Off Valve... -
Page 3: Installation Safety Instructions
INSTALLATION INSTRUCTIONS INSTALLATION SAFETY INSTRUCTIONS BEFORE YOU BEGIN Remove all tape and packing materials before using the cooktop. Dispose all plastic bags after unpacking the cooktop. Never allow children to play with packing materials. IMPORTANT SAFETY INSTRUCTIONS Read these instructions completely and carefully. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. - Page 4 • If cabinets are located above the cooktop, allow a minimum clearance of 30” between the cooking surface and the bottom of unprotected cabinets.
-
Page 5: Dimensions And Clearances
MODEL 30″ Cooktop 30″ ″ 36″ Cooktop ″ 36″ The cooktop may be placed with 2 3/4” clearance to the back wall. RECOMMENDED GAS SUPPLY LOCATION FROM BACKWALL Recommended A˝MIN. clearance from gas supply 3 3/4 MIN. cutout to side wall on... -
Page 6: Installing The Cooktop Unit
Install a manual shut-off valve in the gas line in an easily accessible location outside the cooktop. Be sure you know how and where to shut off the gas supply to the cooktop. Install the electrical outlet 12˝ below the countertop. -
Page 7: Provide Adequate Gas Supply
2. CONNECT THE COOKTOP TO GAS Shut off the main gas supply valve before removing the old cooktop and leave it off until the new hook-up has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on. - Page 8 INSTALLATION INSTRUCTIONS FLEXIBLE CONNECTOR HOOKUP Installer: Inform the consumer of the location of the gas shut-off valve. Pressure regulator Adapter Gas Flow into Range Flex connector (6 ft. max.) Adapter shut-off 1/2” or 3/4” valve Gas pipe...
-
Page 9: Electrical Connections
The customer should have the wall receptacle and circuit checked by a qualified technician to be sure the receptacle is properly grounded. When connecting the cord of this cooktop to a standard two-prong wall receptacle, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded three-prong wall receptacle. -
Page 10: Seal The Openings
(grounding) receptacle by a qualified technician before using this cooktop. 4. SEAL THE OPENINGS Seal any openings in the wall behind the cooktop and in the floor of the cabinet when hookups are completed. (continued) -
Page 11: Assemble The Surface Burners
5. ASSEMBLE THE SURFACE BURNERS CAUTION DO NOT operate the burners without all parts in place. Place the burner caps and heads on the cooktop. Make sure that the caps and heads are placed in the correct locations. Extra large burner... -
Page 12: Adjust The Surface Burner Low Flame (Simmer) Setting
1. Disconnect power to appliance. 2. Remove grates, burners caps, burner heads and knobs. 3. Remove the all the screws on the cooktop by philips screwdriver. 4. Remove cooktop by lifting up. 5. Remove LED lamp module of the center valve by unclipping. -
Page 13: Converting To Lp Gas
CONVERTING TO LP GAS (OR CONVERTING BACK TO NATURAL GAS FROM LP) This cooktop leaves the factory set for use with natural gas. When converting to LP gas, the conversion must be performed by a qualified LP gas installer. - Page 14 Memo...
- Page 15 Printed In Korea Impreso en Korea Imprimé en Corée...