Page 1
Retain it for future reference. Record model number and serial number of the set. See the label attached on the bottom of the set and quote this information to your dealer when you require service. Model number Serial number BX220-JD OWNER’S MANUAL...
Page 2
DLP PROJECTOR DLP PROJECTOR FCC NOTICE • A Class A digital device This equipment has been tested and found to comply with the limits for a Class A digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Projector Status Indicators...10 Accessories...11 Optional Extras ...11 Installing and Composition Installation Instructions ...12 Basic Operation of the Projector...13 Using Kensington Security System...14 Turning on the Projector ...15 Turning off the Projector ...15 Focus and Position of the Screen Image...16 Selecting source mode ...16 Connection Connecting to a Desktop PC ...17...
Outdoor Installation Do not use the projector in a damp place such as a bathroom where it is likely to get wet. This may cause a fire or an electric shock hazard ! Power Earth wire should be connected.
Page 5
This may cause a fire or an electric shock hazard ! Do not turn the projector On/Off by plugging-in or unplugging the power plug to the wall outlet. (Do not use the power plug for switch.) It may cause mechanical failure or could give an electric shock.
Others Do not attempt to service the projector yourself. Contact your dealer or service centre. This may cause damage to the projector and could give an electric Shock as well as invalidating the warranty ! Others Be sure to unplug if the projector...
Names of parts Main Body * The projector is manufactured using high-precision technology. You may, however, see on the Projector screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not always indicate a malfunction.
Names of parts Control Panel MENU Button Selects or closes menus. AUTO Button POWER Button , KEYSTONE+/- Button MENU SOURCE KEYSTONE SOURCE Button Switches to RGB, DVI, Video,S-Video mode. Adjusts functions of menus. KEYSTONE Checks present mode and AUTO saves the change of functions. POWER Button OK Button...
Remote Control POWER Button MENU Button Button AUTO Button (Refer to p.25) BLANK Button (Refer to p.23) Installing Batteries • Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match “+” with “+”, and match “-” with “-”. •...
Names of parts Projector Status Indicators * Lamp Indicator, operation indicator and temperature indicator at the top of the projector show the user the operating status of the projector. Orange Green(flashing) Operation Indicator Green Orange(flashing) Lamp Indicator Red(flashing) Green(flashing) Orange...
* When applying a ceiling installer, use only the ceiling installer for projector. * Contact your service personnel for replacing a new lamp. * Projector lamp is reaching the end of its life and needs to be replaced with a new lamp. Projection Screen...
Don’t place the projector where it can be covered with dust. This may cause overheating of the projector. Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire hazard. The projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the projector Screen.
3.Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page 22.)
Installing and Composition Using Kensington Security System G The projector has a ‘Kensington’ Security System Connector on the back panel. Connect the ‘Kensington’ Security system cable as below. G For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached to the Kensington Security System set.
(Green operation indicator flashes during cooling of the lamp.) G It will take about 12 second to display the picture after power on because the projector lamp has to warm up. G An image will appear after the operation indicator light turns (Green).
1. While pressing the foot adjuster button, raise or lower the projector to place the screen image in the proper position. 2. Release the button to lock the foot in its new position.
Connecting to a Desktop PC * You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output. * You can use ARC function for the RGB signals of the Aspect Ration 4:3. (For HD wide input signals, you cannot use ARC function.) * Fundamentally, HD wide input signal is not included in the Spec, so the set may not support HD signal perfectly.
Connection Connecting to a Video Source * You can connect a VTR, a camcorder, a LDP or any other compatible video image source to the projector. < How to connect 1 > a. Connect the Video input jacks of the projector to the output jacks of the A/V source with Video cable.
Function * In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just example to help with the Projector operation. * If there is no input signal present, the Menu will not be displayed on the screen.
Function Video Menu Options Auto Color Temperature Control 1. Press the MENU button and then use 2. Press the OK ( ) button and then use 3. Press the button to make appropriate adjustments. F, G Each press of the button changes the screen as shown below.
Flip Vertical Function * This function reverses the projected image vertically. * When you hang the projector upside down from the ceiling , you will need to reverse the image vertically and horizontally. 1. Press the MENU button and then use 2.
Using Keystone function * Use this function when the screen is not at a right angle to the projector and the image is a trapezoid shape. * Only use the Keystone function when you can’t get the best angle of projection, because it may cause a blazing fire of the screen.
Using Blank function * This function may be effective if you need to get attention of the audience during presentations, meetings or briefings. 1. Press the BLANK button. The screen turns off to a background color. You can choose the background color. (Refer to ‘Selecting blank image color’) 2.
1. Press the MENU button and then use G The used lamp time is displayed. G When projector lamp is reaching the end of its life (over 2000 hours), the lamp indicator will be turned red. G The lamp warning LED illuminates red continuously in the case of excessive lamp time.
Screen Menu Options Auto Tracking Function *This function assures you of getting the best video quality by automatically adjusting the difference of horizontal size and synchronization of the image. *Auto Tracking function works in RGB input only. 1. Press the AUTO button. Image positioning and synchronization are automatically adjusted.
To exit the menu display, repeatedly, press the MENU button. How to connect external control equipment • Connect the serial port of the PC to the RS-232C jack on the projector back panel. • RS-232C cable is not supplied with the projector.
[Command2] [ ] [Set ID] [ ] [OK] [Data] [x] * The Projector transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
Page 28
RS-232C External control device setup 01. Power (Command2:a) ➜ To control Power On/Off of the Projector. Transmission [k] [a] [ ] [Set ID] [ ] [Data] [Cr] Data 0 : Power Off 1 : Power On [a] [ ] [Set ID] [ ] [OK] [Data] [x]...
Page 29
1 : OSD Select Mode On 11. Remote Control Lock/Key Lock (Command2:m) ➜ To lock the front panel controls on the projector and remote control. Transmission [k] [m] [ ] [Set ID] [ ] [Data] [Cr] Data 0 : Lock Off...
Page 30
[z] [ ] [Set ID] [ ] [OK] [Data] [x] Data Min : 0 ~ Max : 64 16. Low Power (Command2:q) ➜ To reduce the power consumption of the projector. Transmission [ j ] [q] [ ] [Set ID] [ ] [Data] [Cr] Data...
1280X1024 60.020Hz * If the projector does not support the input signal, “Out of Range” message appears on the screen. * The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor) * The Synchronization input form for horizontal and vertical frequencies are Separate, Composite and SOG.
Cleaning the Projector Case To clean the projector case, first unplug the power cable. To remove dirt or dust, wipe the casing with a soft, dry, lint-free cloth. To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing.
In operation : 32~104°F(0°C~40°C) In storage and transit : -4~140°F(-20°C~60°C) humidity In operation : 0~ 80% relative humidity by dry hygrometer Not in operation : 0 ~ 90% relative humidity by dry hygrometer BX220-JD 1024(Horizontal) x 768(Vertical)pixel 4:3(horizontal:vertical) 0.55 inches 1.01~5.08m(40~200 inches) 1:1.2...