Page 2
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Page 3
CDX-L280 TEST DISCS This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability: CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2) Notes on CD-R/CD-RW discs •...
CDX-L280 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. 2-5. CHASSIS (T) SUB ASSY (Page 9) 2-1. SUB PANEL ASSY 2-6. LEVER SECTION 2-7. SERVO BOARD (Page 7) (Page 10) (Page 10) 2-2.
CDX-L280 2-2. CD MECHANISM BLOCK 7 bracket (CD) 5 CD mechanism block 6 PTT 2.6x6 2 PTT 2.6x6 1 PTT 2.6x6 4 CNP701 2-3. MAIN BOARD 3 screw (+BTT) 5 MAIN board 4 screws (+BTT) 2 PTT 2.6x8 1 PTT 2.6x8...
CDX-L280 2-4. HEAT SINK 6 heat sink 5 PTT 2.6x8 4 PTT 2.6x8 3 PTT 2.6x12 2 PTT 2.6x8 1 PTT 2.6x8 2-5. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) sub assy lead wires.
CDX-L280 2-6. LEVER SECTION 5 guide (disc) 6 lever (R) 3 tension spring (LR) 7 lever (L) 1 special screw 2 IN SELF SW board 4 claws 2-7. SERVO BOARD 8 SERVO board 7 special screw 6 special screws 2 Removal the solders.
CDX-L280 2-8. SHAFT ROLLER ASSY • When installing, take note of the positions arm (roller) and washers. (Fig. 1) 3 retaing ring (RA) shaft retainer (roller) washer 4 shaft retainer (roller) washer shaft retainer retaing ring (roller) (RA) Fig. 1...
CDX-L280 SECTION 3 DIAGRAMS 3-1. IC PIN DESCRIPTION • IC801 µPD780024AGK-C08-9ET (SYSTEM CONTROLLER) Pin No. Pin Name Pin Description D SW Down switch detection input IN SW Disc in switch detection input PH3 detection input (Not used in this set)
Page 14
CDX-L280 Pin No. Pin Name Pin Description P.ON System power supply control output X SO CD DSP IC serial data output X SI CD DSP IC serial data input X SCK CD DSP IC serial clock output RFOK CD servo IC RFOK signal input...
CDX-L280 3-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 17 for Circuit Boards Location. THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: •...
CDX-L280 SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety.
CDX-L280 4-5. CD MECHANISM SECTION (3) (MG-393CX-121//K) M901 (Supplied with 201) M902 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
CDX-L280 SECTION 5 DISPLAY ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
Page 34
CDX-L280 DISPLAY IN SELF SW LOAD SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R561 1-216-806-11 METAL CHIP 1/10W A-3274-620-A MAIN BOARD, COMPLETE (including R562 1-216-806-11 METAL CHIP 1/10W SPEAKER BOARD) R563 1-216-817-11 METAL CHIP...
Page 40
CDX-L280 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2002. 11...