Advertisement
A single-phase,
60-Hz, AC-only,
electrical
supply is required
on a
separate
circuit.
A time-delay
fuse or circuit
breaker
is required:
15amp
for models without
electric
heater
and 30.amp
for
models with electric
heater.
The
fuse size must not exceed
the
circuit
rating specified
on the
model
and serial label,
The model
and serial label is located
behind
the front panel on the base
flange.
serial label
Specific
electrical
requirements
are listed in the chart.
Follow the
requirements
for the type of plug
on the power supply cord,
Plug Type
3.p1ong
qoundlng
dug
j-prong
groundng-
type wall
power
supply
cord
114'
Ilade
lJron!3
grounding
prong
receptacle
groundlng
prong
Electrical
lequirements
115-voll
models
rated
up through
12.0 amperes
230.voll
and
230/208-volt
models
rated
up through
12.0 amperes
230.volt
and
230/208-volt
models
rated
up lhrough
16.0 amperes
230.voll
and
230/208-voll
models
rated
up lhrough
24.0 amperes
Minimum
receptacle
wire
size
14
gauge
14
Gwe
12
gauge
10
gauge
Recommended
grounding
method
For your personal
safety, this
appliance
Imust be grounded.
This
appliance
is equipped
with a
power supply cord having
a
3-prong
grounding
plug.
To
minimize
possible shock hazard,
the cord must be plugged
into a
mating,
3-prong
grounding-type
wall receptacle,
grounded
in
accordance
with the National
Electrical
Code, ANSI/NFPA 70 -
latest edition',
and all local codes
and ordinances.
If a mating
wall
receptacle
is not available,
it is
the personal
responsibility
and
obligation
of the customer
to
have a properly
grounded,
3-
prong wall receptacle
installed
by
a aualified
electrician.
Now start...
With air conditioner
in room where
it will be installed.
THROUGH-THE-WALL
INSTALLATION
INSTRUCTIONS . . . FOR SLIDE-
OUT CHASSIS MODEL ONLY.
It is the customer's
responsibility
and obligation
to have this
product
installed
by a qualified
technician
farnlliar
with
through-the-wall
room air
conditioner
installations,
appropriate
header
if required
casing
lrim
112"
@
i
pluster
10'
alternate
construclion
for plaster
Provide
l-3/1 6"
caulk
louvers
clearance
for
power
supply
cord entry on
Ieli side.
I -3/16" clearance
for power supply
cord
Frame
construction
appropriate
header
if required
trim
lintel
I/2"
@
plaster
allernate
1
constructlon
for plaster
Provide
l-
3/l 6"
clearance
caulk
for power
to frame.
supply cord
entry on lett
l-3/16"
cleflrance
for
side.
power
supply cord.
Brick veneer
construction
1
When using a wood,
n
metal or plastic molding,
the finish frame should line up with
inside wall.
If the plastered
wall is
to be flush with the cabinet
and
no molding
is used, the finish frame
must be set l/2 inch into the wall.
of cabinet)
depends
on
wall
thickness
and
type
of
molding.
Cut opening
through
the wall.
Remove
insulation.
3
Use l-inch
or heavier
n lumber
for wood
frame.
Measure
depth
of wall opening
and frame.
Apply wood
preservative
to the
outside
exposed
surface.
4
Insert the frame in the
n
wall opening.
Square
and level frame.
Nail frame
securely
to the wall studs.
Page 3
Advertisement
