Advertisement
Quick Links
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY
A QUALiFiED iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL
iNSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.
This conversion
kit must be installed by a qualified
service
technician
in accordance
with the
manufacturer's
instructions and all applicable
codes and requirements
of the authority
having jurisdiction.
Failure
to follow instructions may result in fire, explosion
or production
of carbon
monoxide
causing
property
damage,
personal
injury or loss of life. The qualified
service agency is responsible
for the proper instaJlation of this kit. The
installation is not proper and complete
until the operation
of the converted
appliance
is checked
as specified
in
the manufacturer's
instructions supplied
with this kit.
Before
proceeding
with the conversion,
shut off the gas supply
before disconnecting
electrical
power to the range. Be sure both power supplies
are off before installing the conversion
kit. Failure to do so could
cause serious bodily injury.
NOTE: When surface
burners
are converted
from Natural
to L.P. the BTU ratings
become:
3,000 BTU* Natural
Gas to 2,000 BTU* LP. Gas
5,000 BTU* Natural
Gas to 4,500 BTU* LP. Gas
9,000 BTU* Natural
Gas to 8,000 BTU* LP. Gas
*NOTE: For operation
at elevations
above 2000 ft., appliance rating shah be reduced at
13,000 BTU* Natural Gas to 12,000 BTU* L.P. Gas
the rate of 4 percent for each 1000 ft. above sea level.
L.P. Kit Contents
Kit pin 316467200 (white)
Part Description
Part Number
Qty.
Surface Burner Orifice marked 0.68 mm 4,500 BTU* (blue)
Surface Burner Orifice marked 0.89 mm 8,000 BTU* (no color)
Surface Burner Orifice marked 0.40 mm 2,000 BTU* (no color)
Surface Burner Orifice marked 1.02 mm 12,000 BTU* (no color)
L.P. Kit Installation Instructions
316237907
316237906
316467402
316467403
316417509
1
3
1
1
1
Tools
Required"
3/8", 1/2" and 5/8" Open End Wrench
1/8" Wide Flat Blade Screwdriver
7ram Nutdriver
9/64" Allen socket wrench
How to Convert
the Range for use with LP/
Propane
Gas
1.
Convert the Pressure Regulator:
To access
the gas regulator,
remove
the storage drawer
or Warmer
Drawer.
if equipped
with a storage drawer, open & remove
the drawer
completely.
For models
equipped
with a Warmer
Drawer,
follow
the
instructions below to remove
the Warmer
Drawer.
a.
_
EJectrical Shock Hazard can occur and result in
serious injury or death. Disconnect
electrical
power to the range
before removing the Warmer
Drawer for servicing.
b.
Locate glide lever on each side of drawer, puJJup on the left glide lever
and push down on the right glide lever (See Fig. 1).
c.
Pull the Warmer
Drawer away from the range (See Fig. 2).
d.
Remove the regulator access cover if equipped.
Do not remove
the
Pressure
Regulator
or allow
it to turn.
e.
Remove the dust protector from the cap (Gas models). Use the proper
size wrench
to remove the cap from the regulator(All
models).
f.
Follow the remaining instructions provided in Fig. 3.
NOTE:
After replacing
the natura!
to keep
the erigina!
factory
installed
natura!
gas orifices
for
future
range
conversion
back
to natural
gas.
LEFT GLIDE
PULL UP WITH FINGER
RIGHT GLIDE
PUSH DOWN WITH FINGER
Fig. 1
"o Q°
"® o-°
-
,j
Front Access
to Regulator:
Remove
Warmer
Drawer
Pressure
Regulator
Fig. 2
p/n 316417509 (0605)
1
Advertisement
