Advertisement

SERVICE MANUAL
Read this manual carefully, especially precaution on microwave energy, and follow the procedure
strictly. Careless servicing and testing may expose yourself to the microwave energy leakage.
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID
POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or
other microwave source, and make repairs if necessary:
(1) Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and
other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or
abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave
generating compartments, check the magnetron, wave-guide or transmission line, and cavity for
proper alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures
described in this manual before the oven is released to the owner.
STAINLESS STEEL
MICROWAVE OVEN WITH
CONVECTION AND GRILL
MI N
SE C
AU TO
1.
2.
3.
C
/
Kg
FOREW ORD
PRECAUTIONS
FILE No.
EM-SL30NEUKUK
MIN
AUTO
1.
2.
3.
Product Code No.
EM-SL30NEUK
REFERENCE No.
SEC
C
/
Kg
1-437-574-26
SM
-2400004

Advertisement

Table of Contents
loading

Summary of Contents for Sanyo EM-SL30NEUK

  • Page 1 MI N SE C AU TO Product Code No. 1-437-574-26 EM-SL30NEUK FOREW ORD Read this manual carefully, especially precaution on microwave energy, and follow the procedure strictly. Careless servicing and testing may expose yourself to the microwave energy leakage. PRECAUTIONS...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Adjustment Procedures........1 Circuit Diagram............ 4 Specifications............2 Test Procedures and Troubleshooting....5-15 Power Output Measurement........ 2 Disassembly Instructions........16-17 Precautions and Repair Service Tips....2 Exploded View and Parts list........18-23 Oven Control Panel..........3 Control Circuit Board..........24 Overall Circuit Diagrams........25 CAUTION MICROWAVE ENERGY PERSONNEL SHOULD NOT BE EXPOSED TO...
  • Page 3: Specifications

    2. SPECIFICATIONS - EM-SL30N 4.PRECAUTIONS AND REPAIR SERVICE TIPS PRELIMINARY Rated Power Consumption..Micro. 1450+15%W Conv. 1200+5/-10%W Grill 1100+5/-10%W A.SINCE NEARLY 4,000 VOLTS EXIST IN Dual 2550+15%W SOME CIRCUITS OF THIS MICROWAVE OVEN, REPAIRS SHOULD BE CARRIED (After 15mins.) OUT WITH GREAT CARE Microwave Output......
  • Page 4: Oven Control Panel

    5. OVEN CONTROL PANEL AUTO Figure 1 KEYS: 1. Display Window 8. Personal Menu Keys 2. Function and Accessary Indicator 9. Slow Cook 3. Kitchen Timer Display 10. Dual Cook 4. Auto Program Key 11. Quick Start 5. Auto-Defrost 12. Clear/Stop 6.
  • Page 5: Circuit Diagram

    230V ~ 6.CIRCUIT DIAGRAM 50Hz EM-SL30N OVEN CONDITION FUSE (8A T) DOOR : OPEN L1,L2 = 1mH C1 = 0.22 F C2,C3 = 4700PF R = 1M MTCO/ CFTCO TOUCH KEY BOARD S101 CONTROL CIRCUIT SHTCO BOARD HIGH VOLTAGE TRANSFORMER S102 HV FUSE MAGNETRON 2M-253H(IF)-N...
  • Page 6: Test Procedures And Troubleshooting

    7. TEST PROCEDURES AND TROUBLESHOOTING Filament Windings CAUTION - DISCONNECT THE POWER SUPPLY CORD FROM THE WALL OUTLET WHENEVER REMOVING THE CABINET FROM THE UNIT. PROCEED WITH THE TESTS ONLY AFTER DISCHARGING Secondary Winding THE HIGH VOLTAGE CAPACITOR AND REMOVING THE LEAD WIRES FROM THE PRIMARY WINDING OF THE HIGH VOLTAGE TRANSFORMER.
  • Page 7 COMPONENT CHECKOUT PROCEDURE RESULTS 1) Measure the resistance : Normal readings : With an ohmeter on Rx1 scale. a. Primary Winding ; Approximately 1.7 ohms. b. Filament Winding ; Less than 1 ohm. c. Secondary Winding ; Approximately 92 ohms. 2) Measure the resistance : Normal readings : With an ohm-meter on highest scale.
  • Page 8 COMPONENT CHECKOUT PROCEDURE RESULT Measure the resistance: Between the Pin 1 and Normal Reading: Pin 3 of connector S103 after disconnecting Approximately THERMISTOR it from the control circuit board with an 1800K ohms @ 20˚C ohm-meter on the highest scale. 1400K ohms @ 25˚C Normal Reading: CONVECTION...
  • Page 9 COMPONENT CHECKOUT PROCEDURE RESULTS Measure the resistance : Across two terminals with an ohm-meter on its highest scale. Normal reading : Indicates continuity. HV FUSE Abnormal reading : Indicates infinite ohms. Figure 10 Measure the voltage : Between test points TP-1,TP-2 and ground ( See control circuit board on page 24 ).
  • Page 10 CHECKOUT PROCEDURE FOR SWITCHES Disconnect the lead wires from the switches and check the continuity of the switches, connecting an ohm-meter to its terminals. SWITCH CHECKOUT PROCEDURES DOOR OPEN DOOR CLOSE Primary Interlock Connect an ohm-meters leads to terminals "COM" and "NO"...
  • Page 11 -10-...
  • Page 12 -10- -11-...
  • Page 13 -12-...
  • Page 14 -13-...
  • Page 15 -14-...
  • Page 16 -15-...
  • Page 17: Disassembly Instructions

    8.DISASSEMBLY INSTRUCTIONS C. REMOVING MAGNETRON (See exploded view on page 20 ) - OVEN MUST BE DISCONNECTED FROM ELECTRI- (1) Remove the antenna complete according to CAL OUTLET WHEN MAKING REPLACEMENTS, B. REMOVING THE ANTENNA. REPAIRS, ADJUSTMENTS, AND CONTINUITY (2) Disconnect the 2 lead wires from the magnetron. CHECKS BEFORE PROCEEDING WITH ANY REPAIR (3) Remove 1 screw securing the duct to the WORK AFTER DISCONNECTING.
  • Page 18 4. The hinge screws should then be tightened to hold the (3) Remove power cord from cavity assembly by door in place, and the feeler gauges removed. lifting cord bush, moving it to the left and pulling it 5. The door gap should then be checked again using feeler away from cavity rear plate.
  • Page 19: Exploded View And Parts List

    9. EXPLODED VIEW AND PARTS LIST CAVITY PARTS-A EM-SL30N Part No. Description Q'ty Part No. Description Q'ty MO-A0731 Cavity Assembly 19 617 177 3231 Motor Complete 617 220 4376 Cabinet 20 617 202 4561 Thermostat, V122˚C 617 221 5433 Duct 21 617 177 3200 Heater Ass’y 617 202 4554 Thermostat, V150˚C 22 617 179 0733 Collar...
  • Page 20 CAVITY PARTS-B EM-SL30N Part No. Description Q'ty MO-A0737 Antenna Complete 617 169 8930 Cavity Cover 617 212 8177 Thermistor Ass’y 617 206 5717 Frame Rear Plate 617 206 5083 Cook Net 617 206 5090 Cook Net 411 156 5601 SCR TPG PAN+F+S 4x10 411 165 0406 SCR TPG TRS 4x10 SUS 411 053 9306 NUT HEX +LFLC W/SRT 4 1 10 412 048 6508 SCR TPG TRS 4x10...
  • Page 21 SWITCHES AND MICROWAVE PARTS EM-SL30N Part No. Description Q'ty Part No. Description Q'ty 617 112 1025 411 156 5601 SCR TPG PAN+F+S 4x10 MO-M1211 Duct 411 156 5502 SCR S-TPG PAN +F+S 4x10 617 195 3428 Latch Lever 617 220 4925 Power Cord Ass’y 617 189 0839 Lever Stopper...
  • Page 22 MICROWAVE PARTS EM-SL30N Part No. Description Q'ty 617 228 8475 Transformer 617 225 1721 Special Screw 617 225 6146 Bottom Plate Assembly ------------------ Gear Motor Cover MO-S0168 Foot Cushion Assembly 617 166 7493 Bottom Hinge 411 156 5602 SCR S-TPG PAN+F+S 4x10 1 617 102 7495 Special Screw -21-...
  • Page 23 DOOR PARTS Inner Door Panel always supplied with Door Main Frame but can be ordered seperately quoting number below. EM-SL30N Part No. Description Q'ty MO-A0750 Door Cover Assembly MO-A0768 Door Main Frame(Supplied 1 with inner Door Panel) 617 144 2472 Glass Inner Door Panel 617 167 0189 Hinge 617 167 1292 Choke Dielectric 617 195 3411 Door Latch...
  • Page 24 CONTROL PANEL PARTS EM-SL30N Part No. Description Q'ty MO-A0752 Control Base Assembly 617 236 6463 Knob Body 617 219 5520 PCB Complete 617 241 1941 PCB Complete 617 208 4602 Insulation Sheet 617 197 4836 PCB Complete 617 181 7980 Latch Lever MO-A0747 Handle Assembly 617 188 3329 Spring...
  • Page 25: Control Circuit Board

    10.CONTROL CIRCUIT BOARD EM-SL30N Model Spares No. M.Processor EM-SL30N 617 241 1941 IC11 LM8843 4 9 8 0 0 -24-...
  • Page 26: Overall Circuit Diagrams

    11. OVERALL CIRCUIT DIAGRAM EM-SL30N IC 11 LM8843 -25-...
  • Page 27 Please Note All the information that appears in this service manual was correct at the time of production. SANYO Electric Company reserves the right to make changes to parts or processes in order to maintain their policy of continuing improvement.

Table of Contents