Toshiba GD-1300 Service Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Fax Machine
  5. GD-1300
  6. Service manual
Toshiba GD-1300 Service Manual

Toshiba GD-1300 Service Manual

Hide thumbs Also See for GD-1300:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
SERVICE MANUAL
FACSIMILE
GD-1300
Model: GD-1300
Publish Date: July 2008
File No. SME08000400
R080621G0700-TTEC
Ver00_2008-07

Advertisement

Table of Contents
loading

Related Manuals for Toshiba GD-1300

Summary of Contents for Toshiba GD-1300

  • Page 1 SERVICE MANUAL FACSIMILE GD-1300 Model: GD-1300 Publish Date: July 2008 File No. SME08000400 R080621G0700-TTEC Ver00_2008-07...
  • Page 2 © 2008 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION. No patent liability is assumed, however, with respect to the use of the information contained herein.
  • Page 3 GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR e-STUDIO203S/203SD AND GD-1300 The installation and service should be done by a qualified service technician. 1. Transportation/Installation When transporting/installing the machine, be sure to use the positions as indicated below. The machine is quite heavy and weighs approximately 17 kg (37 lb.), therefore pay full attention when handling it.
  • Page 4 Be sure to handle/install them properly. If these parts are shorted circuit and/or made their functions out, they may burn down, for instance, and may result in fatal accidents. Do not allow a short circuit to occur. Do not use the parts not recommended by Toshiba TEC Corpora- tion.

  • Page 5: Product Outline

    0 - 3 characters Communication start Max. speed: 33600bps/ High speed: 14400bps/ speed Middle speed: 9600bps/ Low speed: 4800bps International NO/ Mode 1/ Mode 2/ Mode 3 communication mode Transmission method One-touch dial key GD-1300 PRODUCT OUTLINE 1 - 1...
  • Page 6 Super Fine: 8dot x 15.4 line/mm Half-tone: Scan in 256 gradations Document table scan Book document scan/send function from the (OC send) function document table (OC). In one send job, the send document size is fixed. GD-1300 SPECIFICATIONS 2 - 1...
  • Page 7 Serial broadcast Broadcast send Max. 100 items function destination Duplex send function Valid only in duplex support models. Direct send and scan from OC cannot be made. Send document size A4/ Letter/ Legal size GD-1300 SPECIFICATIONS 2 - 2...
  • Page 8 Number of items of destination registration: Max. 100 communication items Remote send Scanned document data in memory are sent automatically by send request from the remote machine. Protection function • Check by sender number • Check by allow number GD-1300 SPECIFICATIONS 2 - 3...
  • Page 9 Communication report Report select • Send report list list • Receive report list • Serial broadcast send report list • Image memory addition Print status select • ALWAYS PRINTS • ERROR ONLY • NEVER PRINTS GD-1300 SPECIFICATIONS 2 - 4...
  • Page 10 First Sunday of November AM2:00 → 1:00 (Default: OFF) (Europe) Last Sunday of March AM1:00 → 2:00, Last Sunday of October AM1:00 → 0:00 (Default: ON) Multi language Conforms to the main unit setting. function GD-1300 SPECIFICATIONS 2 - 5...

  • Page 11: Installation Procedure

    Remove all pieces of fixing tape and fixing materials from the finisher. 2. Installation procedure (1) Detach the RADF or OC. Detach the RADF or OC from the copier and softly place it on top of the original table as shown below. GD-1300 INSTALLATION PROCEDURE 3 - 1...
  • Page 12 (6) Work the rear cabinet, and attach the gasket. 1) Cut and remove the cut-out portion from the rear cabinet using a tool such as nippers. (Be careful with the tool’s direction so that the cut surface is flat.) GD-1300 INSTALLATION PROCEDURE 3 - 2...
  • Page 13 FCC label FCC label Putting standard Insert the power plug of the copier to the outlet and turn on the main switch of the copier. Then, carry out the following procedure. GD-1300 INSTALLATION PROCEDURE 3 - 3...

  • Page 14: Entering The Simulation Mode

    FAX soft SW initializing (excluding the adjustment Communication time measurement values) Speaker sound volume setting FAX PWB memory check Time setting/check Signal send mode (Max. value) Signal send mode (Soft SW set value) Image memory content print GD-1300 SIMULATION 4 - 1...
  • Page 15 2) Enter a 2-digit value as the exposure adjust- ment value with [Numeric] key. ADJUST EXP. AUTO PRINT ADJUST EXP. AUTO After completion of printing, returns to “2)” dis- play. ("YY" is the entered exposure adjustment value.) GD-1300 SIMULATION 4 - 2...
  • Page 16 EXP. S-FINE 2) Enter a 2-digit value as the exposure adjust- PRINT ment value with [Numeric] key. After completion of printing, returns to “2)” ADJUST EXP. S-FINE display. ("YY" is the entered exposure adjustment value.) GD-1300 SIMULATION 4 - 3...
  • Page 17 After 2sec, returns to "1) Initial display". FAX soft SW [Function] initializing (excluding Use to initializing FAX soft SW. the adjustment values) [Operation] 1) Initial display INITIALIZED After 2sec, main code and sub code input display. GD-1300 SIMULATION 4 - 4...
  • Page 18 1:NO SIGNAL 35:LINE ON HOOK ∗ [Clear] key: Returns to the main-sub code input display. 3) [ENTER]/[OK] key Send after setting OUTPUTING SIGNAL MAX PRESS CLEAR TO STOP ∗ [Clear] key: Returns to "1) Initial display". GD-1300 SIMULATION 4 - 5...
  • Page 19 After completion of memory clear, the buzzer After completion of memory clear sounds. CLEARED CLEARED PLEASE POWER OFF After 2sec, main code and sub code input dis- Remains unchanged until the power is turned play. off. GD-1300 SIMULATION 4 - 6...
  • Page 20 ..SELECT SIGNAL (1-6) 1:NO SIGNAL 6:00001 ∗ [Clear] key: Returns to the main-sub code input display. 3) [ENTER]/[OK] key OUTPUTING SIGNAL SSW PRESS CLEAR TO STOP ∗ [Clear] key: Returns to "1) Initial display". GD-1300 SIMULATION 4 - 7...
  • Page 21 PRESS CLEAR TO STOP ∗ [Clear] key: Returns to the main-sub code ∗ [Clear] key: Returns to "1) Initial display". input display. 2) [Numeric] key input The content selected with signal send level selection is set inside. GD-1300 SIMULATION 4 - 8...
  • Page 22 Use to check the TEL/LIU status change. [Operation] 1) Initial display HS2 :xxx HS1 :xxx RHS :xxx EXHS:xxx ↑ The display is switched every 2sec. ↓ CHECKING PRESS CLEAR TO STOP ∗ [Clear] key: Returns to the main-sub code input display. GD-1300 SIMULATION 4 - 9...
  • Page 23 ] key is pressed, the sequence is reversed. SELECT (1-4) SELECT (1-4) ..1:NO SOUND 2:LOW ∗ [Clear] key: Returns to the main-sub code input display. 3) [ENTER]/[OK] key STORED xxx: Set content After 2sec, main code and sub code input display. GD-1300 SIMULATION 4 - 10...
  • Page 24 6) Select 1 "xxxx.xx.xx(xxx) is the entered value. STORED ∗ Select 2: Returns to "1) Initial display". 7) Select 1 After 2sec, returns to "1) Initial display". STORED After 2sec, returns to "1) Initial display". GD-1300 SIMULATION 4 - 11...
  • Page 25 Reception print Paper selection Automatic reduction print User program SW 24-8 When reduction print is not made Index Index print setup User program SW 32-6 When an index is attached to the reception data GD-1300 FAX SOFT SWITCH 5 - 1...

  • Page 26: Soft Switch List

    0 0 0 0 0 (BUSY)”. Set range 1 to 15min 3min 1 1 1 1 1 When a value outside the set range is set, 1 1 1 1 1 the initial value is set. GD-1300 FAX SOFT SWITCH 5 - 2...
  • Page 27 1 1 1 1 1 Dial tone ON/OFF 1: 1000ms/1200ms 0: 700ms/400ms detection time upper limit-1 1000ms/1200ms 1 1 1 1 1 (Intermittent detection) Quick online send 1: Yes 0: No 1 1 1 1 1 GD-1300 FAX SOFT SWITCH 5 - 3...
  • Page 28 0 0 0 0 0 0 0 0 0 0 Ringing volume Bit No. Refer to User program “RINGER VOLUME”. Silent 1 1 1 1 1 Small Medium Medium 0 0 0 0 0 Large GD-1300 FAX SOFT SWITCH 5 - 4...
  • Page 29 ECM MMR mode 1: Yes 0: No 1 1 1 1 1 (Except for SG3) ECM JBIG mode 1: Yes 0: No 1 1 1 1 1 (Except for SG3) GD-1300 FAX SOFT SWITCH 5 - 5...
  • Page 30 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 6...
  • Page 31 1 1 1 1 1 scan completion sound / alarm sound)” Inhibited to use 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 7...
  • Page 32 Print inhibited Only the address When a value outside to which All print the set range is set, transmission is Only the address to the initial value is set. failed which transmission is failed GD-1300 FAX SOFT SWITCH 5 - 8...
  • Page 33 1 to 255sec 1 1 1 1 1 0 0 0 0 0 45sec 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 GD-1300 FAX SOFT SWITCH 5 - 9...
  • Page 34 Allow 0 0 0 0 0 (U.S.A., Canada) FAX receive auto 1: Allow 0: Inhibit Refer to User program select by CNG Allow 1 1 1 1 1 “FAX SIGNAL AUTO detection RECEIVE”. GD-1300 FAX SOFT SWITCH 5 - 10...
  • Page 35 180 degrees 1 1 1 1 1 duplex back rotation surface print Priority in the day 1: Yes 0: No No (A/B/C/F/G) 0 0 0 1 1 of week Yes (D/E) GD-1300 FAX SOFT SWITCH 5 - 11...
  • Page 36 –6dBm the initial value is set. Set range 0 (0.0dBm) to (A/B/C/D/E) 1 1 1 1 1 21 (–21.0dBm) –5dBm (F/G) 1 1 1 1 1 1.0dBm unit 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 12...
  • Page 37 1 2 3 0 0 0 0 0 (A/B/C/D/E) time Set range 0 (155ms) to 7 (225ms) 195ms (F/G) 0 0 0 0 0 Step 10ms Inhibited to use 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 13...
  • Page 38 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 14...
  • Page 39 1ms 31ms (F) 0 0 1 1 1 34ms (G) Inhibited to use 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 15...
  • Page 40 1: 6 times 0: 7 times 6 times Inhibited to use CNG send start Bit No. When a value outside the set range is set, 0.5sec 0.5sec the initial value is set. 1.0sec 1.5sec GD-1300 FAX SOFT SWITCH 5 - 16...
  • Page 41 Scan magnification ratio adjustment 1: – 0: + (sub scan) flag Scan magnification ratio adjustment Binary input (RADF sub scan) Bit No. 2 3 4 5 6 7 8 Set range 0 to ±12.7% 0.1% interval GD-1300 FAX SOFT SWITCH 5 - 17...
  • Page 42 0 0 0 1 0 0 0 1 Netherlands: 6 0 0 0 0 0 1 1 0 Luxembourg: 3 0 0 0 0 0 0 1 1 Belgium: 3 0 0 0 0 0 0 1 1 GD-1300 FAX SOFT SWITCH 5 - 18...
  • Page 43 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GD-1300 FAX SOFT SWITCH 5 - 19...
  • Page 44 Symbol speed 2800 enable in V.34 1: Enable 0: Disable Enable communicate Symbol speed 2743 enable in V.34 1: Enable 0: Disable Enable communicate Inhibited to use Inhibited to use Inhibited to use GD-1300 FAX SOFT SWITCH 5 - 20...
  • Page 45 16 lines interval (600dpi) Print effective image area sub scan Binary input rear edge void (Back surface) Bit No. 5 6 7 8 48 lines Set range 0 to 240 lines 16 lines interval (600dpi) GD-1300 FAX SOFT SWITCH 5 - 21...
  • Page 46 (RADF back surface sub scan) flag Scan magnification ratio adjustment Binary input (RADF back surface sub scan) Bit No. 2 3 4 5 6 7 8 Set range 0 to ±12.7% 0.1% interval GD-1300 FAX SOFT SWITCH 5 - 22...
  • Page 47 AB series. When set to 1, CED signal send is performed. Default: 0 1 (Conforms to the machine information.) When set to 0, CED signal send is not performed. Default: 1 (Yes) GD-1300 FAX SOFT SWITCH 5 - 23...
  • Page 48 Default: 0 (Allow) Used to set the time from displaying the destination to the next oper- SW10 No.3–No.5 Inhibited to use ation in one-touch dial or reduction dial. Default: 0 0 (2sec) GD-1300 FAX SOFT SWITCH 5 - 24...
  • Page 49 Default: 1sec (North America) / 6sec (Other than North America) Default: 0 0 (No fixing) SW22 No.1–No.8 Inhibited to use SW16 No.7, No.8 Inhibited to use SW23 No.1–No.8 Inhibited to use SW17 No.1 Inhibited to use GD-1300 FAX SOFT SWITCH 5 - 25...
  • Page 50 SW33 No.2–No.7 Inhibited to use Used to set the number of calls to switch to auto receive in manual receive mode. When set to 0, switch to auto receive is not made. Default: 0 time GD-1300 FAX SOFT SWITCH 5 - 26...
  • Page 51 When set to 2400bps, all of SW91 No. 1 – 8 must be set as "Dis- SW38 No.7 Transfer function able". Used to set whether transfer function is enabled or not. Default: 33600bps Default: 1 (Allow) GD-1300 FAX SOFT SWITCH 5 - 27...
  • Page 52 Used to set detection time of CED/ANSam signal for judgment of SW46 No.4 Center No. in FAST mode detection. Default: 1000ms Used to set which is set as FAST center number, Service-No or Host-Tel-No. Default: 0 (Service-No.) GD-1300 FAX SOFT SWITCH 5 - 28...
  • Page 53 Default: 0 (Super G3 disabled) SW57 No.2 Toshiba machine mode SW52 No.5 Error process in RTN reception Used to set whether communication is made in Toshiba machine Used to set whether RTN reception is judged as an error or not. mode or not.
  • Page 54 When set to 1, check is made only with EYE-Q value (EQM value). Therefore, TCF check is loosely made. When set to 0, check is made with received data and EYE-Q value (EQM value). Default: 0 (0 reception & EYE-Q check) GD-1300 FAX SOFT SWITCH 5 - 30...
  • Page 55 Used to set country code. communicate SW81 No.1–No.8 Language information Used to set whether use of 2800Hz is allowed or not as symbol Used to set language. speed in V.34 communicate. Default: 1 (Enable) GD-1300 FAX SOFT SWITCH 5 - 31...
  • Page 56 Image loss on the rear edge in OC sub scan direction can be adjusted. When the set value is increased, image loss is increased. Setting is made in binary input in the increment of 16 lines. Default: 144 lines GD-1300 FAX SOFT SWITCH 5 - 32...
  • Page 57 (Sub scan back surface) Used to set the sub scan magnification ratio in back surface print. By binary input, setting can be made in the range of 0 – ±12.7% in 0.1% increments. Default: 0% GD-1300 FAX SOFT SWITCH 5 - 33...

  • Page 58: Trouble Codes

    For 16 or later, V.34 mode function on the confidential function when communication. other party sending a confidential Busy The calling side cannot message. (Including the connect the line with the other company’s machines) other party. GD-1300 TROUBLE CODES 6 - 1...
  • Page 59 PPS-EOM PIP, PIN PPS-MPS, PPS-NULL RTN, RTP PRI-Q No signal EOR-Q PPS-PRI-Q V.8 Phase-1 V.8 Phase-1 V.8 Phase-2 V.8 Phase-2 V.8 Phase-3 V.8 Phase-3 (Note) For error codes 16 – 31, V.34 mode communication. GD-1300 TROUBLE CODES 6 - 2...

  • Page 60: Circuit Diagram

    [7] CIRCUIT DIAGRAM 1. FAX MAIN PWB (North America) GD-1300 CIRCUIT DIAGRAM 7 - 1...
  • Page 61 GD-1300 CIRCUIT DIAGRAM 7 - 2...
  • Page 62 GD-1300 CIRCUIT DIAGRAM 7 - 3...
  • Page 63 GD-1300 CIRCUIT DIAGRAM 7 - 4...
  • Page 64 GD-1300 CIRCUIT DIAGRAM 7 - 5...
  • Page 65 GD-1300 CIRCUIT DIAGRAM 7 - 6...
  • Page 66 2. FAX MAIN PWB (Europe) GD-1300 CIRCUIT DIAGRAM 7 - 7...
  • Page 67 GD-1300 CIRCUIT DIAGRAM 7 - 8...
  • Page 68 GD-1300 CIRCUIT DIAGRAM 7 - 9...
  • Page 69 GD-1300 CIRCUIT DIAGRAM 7 - 10...
  • Page 70 GD-1300 CIRCUIT DIAGRAM 7 - 11...
  • Page 71 GD-1300 CIRCUIT DIAGRAM 7 - 12...

  • Page 72: Fax Operation

    3. FAX OPERATION GD-1300 CIRCUIT DIAGRAM 7 - 13...
  • Page 73 Memo...
  • Page 74 Memo...

  • Page 75: Lead-Free Solder

    LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
  • Page 76 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

Table of Contents