1. Manuals
  2. Brands
  3. Electrolux Manuals
  4. Dishwasher
  5. 5000 Series
  6. Service manual

Electrolux 5000 Series Service Manual

Built-in dishwasher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Service Manual
B u i l t - I n D i s h w a s h e r
5995393914
(0309)

Advertisement

Table of Contents
loading

Related Manuals for Electrolux 5000 Series

Summary of Contents for Electrolux 5000 Series

  • Page 1 Service Manual B u i l t - I n D i s h w a s h e r 5995393914 (0309)

  • Page 2: Table Of Contents

    Table of Contents SAFE SERVICING PRACTICES ............4 OPERATION ..................5 STATIC FILL ........................ 5 DYNAMIC FILL ......................5 WASH SYSTEM ......................6 SOIL SENSING ......................6 MAIN WASH / TEMP ASSURE ................... 7 TEMPERATURE CONTROLS ..................7 RINSE PHASES ......................8 CONDENSATE DRYING ....................
  • Page 3 Table of Contents DISPENSER ......................19 Checking the Dispenser ....................19 FAN DRY UNIT ......................20 Checking Fan Dry Motor ....................20 SERVICE & DISASSEMBLY .............21 SAFETY PRECAUTIONS ..................21 DOOR PANEL ......................21 CONTROL ......................... 22 DISPENSER ......................22 LOWER ACCESS PANEL ..................

  • Page 4: Safe Servicing Practices

    This service manual is intended for use by persons having electrical and mechnical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products, Inc. cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this manual.

  • Page 5: Operation

    OPERATION In order to address service issues with the Electrolux 5000 Series dishwasher, the primary elements of its operation are described below, as well as its physical components. STATIC FILL The cycle begins by activating the drain pump, ensuring the sump is empty.

  • Page 6: Wash System

    OPERATION WASH SYSTEM Once filling is complete, the dishwasher enters the pre-wash phase. The pre- wash phase conditions the soil with water and detergent to prepare it for removal in the main wash phase. Once water enters the tub, the pump draws the water into the sump through a primary filter at the Sump bottom of the tub to prevent food from circulating...

  • Page 7: Main Wash / Temp Assure

    OPERATION MAIN WASH / TEMP ASSURE After the final reading by the soil sensor, the unit drains before starting to fill for the main wash. The tub fills, with the wash motor starting after the low level pressure switch is activated. The detergent dispenser now opens, introducing detergent into the wash cycle.

  • Page 8: Rinse Phases

    OPERATION RINSE PHASES The first rinse phase following the pre-wash portion of a wash cycle. During this rinse phase, the motor ramps up by 100RPM/second to full speed (2800RPM). Once at full speed, however, the motor will cycle between 1600RPM and 2800 RPM throughout the rest of this rinse phase.

  • Page 9: Cycle, Systems & Components

    CYCLE, SYSTEMS & COMPONENTS Knowledge of the dishwasher’s cycles and systems is necessary in diagnosing any potential operational problems. Methods for diagnosing these problems, such as taking resistance readings and testing for closed circuits are outlined in the following section as well. DISHWASHER CONTROL All of the functions and operations of this dishwasher are dictated and monitored by the electronic control.

  • Page 10: Rinse Hold

    CYCLE, SYSTEMS & COMPONENTS DISHWASHER CONTROL (CONT.) Rinse Hold This cycle is intended for dishes that are to be washed later. It is a rinse-only cycle; options and soil sensing are not available. TESTS FOR THE CONTROL Water/Service Test The service test will check the electronic control’s ability to ran all functions of the dishwasher.

  • Page 11: Water Temperature Test Mode

    CYCLE, SYSTEMS & COMPONENTS 1 Fill / Dispenser 0 0 0 2 Fill / Dispenser / Wash 1 0 0 3 Wash / Heat 1 0 1 4 Pause 0 0 0 5 Wash / Heat 1 0 1 6 Wash / Heat / Dispenser 1 0 1 7 Drain 0 1 0...

  • Page 12: Electronic Control And Keypad Assembly

    CYCLE, SYSTEMS & COMPONENTS Electronic Control and Keypad Assembly The control on the dishwasher consists of the control board and the switch assembly. The switch is installed into the top of the outer door panel, an elastomer keypad, used to actuate the switch, is inserted into holes in the top of the outer door panel.

  • Page 13: To Check Inlet Water Valve

    CYCLE, SYSTEMS & COMPONENTS To Check Inlet water valve Disconnect dishwasher from power supply. To access electrical connections to valve, remove lower front panel. Using ohmmeter, check between P3-5 (yellow wire) and P3-8 (white wire). The resistance reading of the solenoid coil should be 1126 ohms.

  • Page 14: Checking Low Water Level Switch

    CYCLE, SYSTEMS & COMPONENTS Checking Low Water Level Switch Disconnect power to dishwasher. Gain access to electronic control and check between P3-9 (orange wire) and P3-8 (white wire). This should be an open contact. These wires are connected to center terminal # 1 and terminal to the right of center # 3.

  • Page 15: Checking High Water Level Switch

    CYCLE, SYSTEMS & COMPONENTS HIGH WATER LEVEL SWITCH (CONT.) Checking High Water Level Switch • Checking continuity through the high water level switch is easier at the control. • Disconnect power to dishwasher. • Gain access to electronic control and check for continuity between the L1 black wire and P3-6 (brown wire).

  • Page 16: Checking The Wash Motor

    CYCLE, SYSTEMS & COMPONENTS WASH MOTOR (CONT.) Checking the Wash Motor · Disconnect dishwasher from power supply · Due to the location of the motor disconnect plug, resistance readings should be made at the control - Remove outer door panel to gain access to the control - The run windings for the motor are connected between P3-1 and P3-4...

  • Page 17: Temperature Sensor And Soil Sensor

    CYCLE, SYSTEMS & COMPONENTS TEMPERATURE SENSOR AND SOIL SENSOR The electronic control reads information from two sensors to adjust the wash cycle. The Thermistor and soil sensor are integrated into the same housing mounted to the right side of the sump. Both sensors extend into the outer section of the sump to perform independent tasks.

  • Page 18: Checking The Soil Sensor

    CYCLE, SYSTEMS & COMPONENTS Checking the Soil Sensor · While in idle mode, simultaneously press and hold Heavy Wash and Start / Cancel buttons. - This activates the sensor value test. - If a number does not display, continue with the test. ·...

  • Page 19: Dispenser

    CYCLE, SYSTEMS & COMPONENTS DISPENSER The dispenser consists of two dispensers in one housing, controlled by the use of one wax motor actuator. The first time the actuator is energized in the cycle, detergent is dispensed. The second time the actuator is energized, rinse agent is dispensed.

  • Page 20: Fan Dry Unit

    CYCLE, SYSTEMS & COMPONENTS FAN DRY UNIT Dishes are dried with a fan driven condensate system. This system is made up of (refer to Figures 20, 21): Fan Dry Motor Air Intake Condensate Duct Condensate Vent As the dishwasher completes its final drain, the fan dry motor forces saturated air across cool baffles in the condensate duct, resulting in the removal of moisture from the air.

  • Page 21: Service & Disassembly

    SERVICE & DISASSEMBLY SAFETY PRECAUTIONS Always turn off the electric power supply before servicing electrical components, testing with an ohmmeter, or replacing parts. Refer to Safe Servicing Procedures at the front of this manual before servicing the dishwasher. All voltage checks should be made with a voltmeter having a full scale range of 130 volts or higher.

  • Page 22: Control

    SERVICE & DISASSEMBLY CONTROL Disconnect dishwasher from power supply. Remove outer door panel (see Service and Disassembly section labeled Door Panel). Lay outer door panel face down on a protective surface. Compress plastic retainers with a pair of pliers to release the electronic control from carrier panel (Figure 23).

  • Page 23: Lower Access Panel

    SERVICE & DISASSEMBLY LOWER ACCESS PANEL Remove bottom kick plate. Remove screws on each side of lower access panel. (See Figure 25) Remove access panel. CAUTION Edges are sharp. Figure 25 Remove these screws DOOR LATCH / DOOR SWITCH Remove outer door panel. (See previous section for detailed instructions.) Remove two screws mounting the latch/switch assembly to inner door panel, and then remove two wires.

  • Page 24: Upper Spray Arm

    SERVICE & DISASSEMBLY UPPER SPRAY ARM The center of the upper spray arm is a locking mount. Turn upper spray arm and mount counterclockwise to remove. (See Figure To reinstall upper spray arm, line up locking posts in center mount with locking tabs on upper spray arm support.

  • Page 25: Center Spray Arm And Upper Rack Manifold

    SERVICE & DISASSEMBLY CENTER SPRAY ARM AND UPPER RACK MANIFOLD Remove upper rack and place rack upside down on a flat surface. Place blade of a very thin putty knife between retaining ring and center spray arm. Lightly twist knife to lift arm from retaining ring. (See Figure 30) Remove manifold from rack by compressing tube retainer clips and sliding tube backwards to clear front mount.

  • Page 26: Upper Spray Arm Mount

    SERVICE & DISASSEMBLY UPPER SPRAY ARM MOUNT Replacing upper spray arm mount requires removal of cabinet. See section on cabinet removal for detailed instructions. Set dishwasher upright and remove upper spray arm. The mount pushes into the top of the tub with a rubber grommet. An arm on the mount holds it in place to prevent turning during removal/installation of the upper spray arm.

  • Page 27: Water Valve

    SERVICE & DISASSEMBLY WATER VALVE Disconnect dishwasher from power supply. Turn off water supply to dishwasher. Remove kick plate and lower access panel. Removal outer door panel may be needed to gain access to necessary parts. Remove wire connect and water supply line. Remove two mounting screws holding water valve to front frame.

  • Page 28: Door Spring

    SERVICE & DISASSEMBLY CABINET REMOVAL (CONT.) Front of cabinet Bottom of dishwasher Back of cabinet Figure 36 Figure 35 Figure 34 DOOR SPRING Remove dishwasher cabinet. See previous section detailed instructions. Raise spring support rod out of mounting hole of “C”arm. (See Figure 38) Reinstall door spring using reverse procedure.

  • Page 29: Hinge "C" Arm

    SERVICE & DISASSEMBLY HINGE “C” ARM Remove dishwasher cabinet. See CABINET REMOVAL for detailed instructions. Remove door spring. See previous section for detailed instructions. Remove two screws that attach inner door panel to hinge. Hinge Remove hinge retainer from hinge pin. Then remove hinge. (See Retainer Figure 39) Replace hinge and install a new hinge retainer.

  • Page 30: Pressure Switch Assembly

    SERVICE & DISASSEMBLY PRESSURE SWITCH ASSEMBLY Remove dishwasher cabinet. See CABINET REMOVAL for detailed instructions. Remove hoses and electrical connections to switches. (See Figure 40) Mounting Screw Remove screw that mounts assembly to side frame. (See Figure Reverse procedure for reinstallation.

  • Page 31: Inline Heater

    SERVICE & DISASSEMBLY INLINE HEATER Disconnect dishwasher from power and water supplies. Remove drain line. Drain pump Right Remove dishwasher from counter top. Lay dishwasher on its back on a protective Front pad. Rear Disconnect wires from heater. Figure 45 Left Slide clamps from heater and remove hoses.

  • Page 32: Wash Motor

    SERVICE & DISASSEMBLY DRAIN PUMP (CONT.) Mount on back of the sump Check valve Figure 46 Lock Figure 47 Push up on lock to release drain pump from mount WASH MOTOR (SEE FIGURE 45) 1. Disconnect dishwasher from power and water supplies. Remove drain line.

  • Page 33: Capacitor

    SERVICE & DISASSEMBLY CAPACITOR Disconnect dishwasher from power and water supplies. Remove drain line. Figure 50 Remove dishwasher from countertop. Lay dishwasher on its back on a protective pad. Capacitor is mounted to back frame of the unit using a mounting nut.

  • Page 34: Sump

    SERVICE & DISASSEMBLY SUMP Remove lower spray arm, filters, and volute cover from Sump mounting screws inside of tub. Remove four screws mounting sump to tub. Disconnect dishwasher from power and water supplies. Remove drain line. Remove dishwasher from underneath countertop. Lay dishwasher on its back on a protective pad.

  • Page 35: Troubleshooting Guide

    TROUBLESHOOTING TIPS SYMPTON CHECK THE FOLLOWING REMEDY Dishwasher will not 1. Fuse (blown or tripped). 1. Replace fuse or reset breaker. operate when turned on. 2. 120 VAC supply wiring 2. Repair or replace wire connection faulty. fasteners at dishwasher junction box.
  • Page 36 TROUBLESHOOTING TIPS SYMPTON CHECK THE FOLLOWING REMEDY Dishwasher will not pump 1. Drain restricted. 1. Clear restrictions. out. 2. Defective drain pump. 2. Replace pump 3. Air lock in drain hose. 3. Check dishwasher installation. 4. Blocked impeller. 4. Check for blockage and clear. 5.

  • Page 37: Parts Breakdown

    PARTS BREAKDOWN DOOR AND CONTROL PANEL...
  • Page 38 PARTS BREAKDOWN DOOR AND CONTROL PANEL POS. NO PART NO DESCRIPTION 5304434830 Screw,Pan HD hi/lo ,#7-19 x 1/2 5304434831 Screw,c/sunk #6 HD ,#8 x 11 AB 5304434832 Screw,taptite ,M5 x 6 Truss HD ,ZC 5304434837 Screw,csk AB ,6 x 3/8 PH ,s/s 5304434838 Screw,inox ,5.2 x 14 5304434840...
  • Page 39 PARTS BREAKDOWN TUB AND FRAME...
  • Page 40 PARTS BREAKDOWN TUB AND FRAME POS. NO PART NO DESCRIPTION 5304434827 Screw,extrudetite ,M4 x 10 PNHD PH 5304434829 Screw,flange HD ,#7-19 x 8 hi/lo 5304434830 Screw,Pan HD hi/lo ,#7-19 x 1/2 5304434832 Screw,taptite ,M5 x 6 Truss HD ,ZC 5304434833 Screw,PH pan HD ,#8 x 19 5304434834 Screw,alkon TT0812 ,#8 x 13 ,black...
  • Page 41 PARTS BREAKDOWN MOTORS AND PUMPS...
  • Page 42 PARTS BREAKDOWN MOTORS AND PUMPS POS. NO PART NO DESCRIPTION 5304434827 Screw,extrudetite ,M4 x 10 PNHD PH 5304434828 Screw,inox ,4 x 16 TT 5304434844 Clamp,drain hose 5304434845 Clamp,hose ,15.5mm ,black 5304434846 Clamp,hose ,17.7mm 5304434847 Clamp,hose ,38mm 5304434848 Clamp,hose ,44mm 5304434849 Clamp,hose ,32mm 5304434850 Clamp,hose ,pressure switch...
  • Page 43 PARTS BREAKDOWN WRAPPER AND TRIM...
  • Page 44 PARTS BREAKDOWN WRAPPER AND TRIM POS. NO PART NO DESCRIPTION 5304434827 Screw,extrudetite ,M4 x 10 PNHD PH 5304434831 Screw,c/sunk #6 HD ,#8 x 11 AB 5304434839 Screw,SAB ,8 x 1/2 PN HD ,ZC 5304434853 Bumper,wrapper top 5304434854 Trim,cabinet top ,stainless 5304434855 Trim,cabinet side ,stainless ,LH 5304434856...
  • Page 45 PARTS BREAKDOWN RACKS...
  • Page 46 PARTS BREAKDOWN RACKS POS. NO PART NO DESCRIPTION 5304434920 Spray arm,upper assy. 5304434921 Tube,spray arm ,upper 5304434950 Rack,upper assembly ,complete 5304434951 Roller,easylift assy. ,LH 5304434952 Handle,front ,interior 5304434953 Handle,front ,exterior 5304434954 Bumper,door 5304434955 Basket,silverware assy 5304434956 Rack,lower assembly ,complete 5304434957 Roller Assembly,lower rack 5304434958 Fence,fold down ,front ,lower rack...

  • Page 47: Electrical Diagram

    WIRING DIAGRAM...

Table of Contents