1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Drill
  5. DWD024S-XE
  6. Instruction manual

DeWalt DWD024S-XE Instruction Manual

Hide thumbs Also See for DWD024S-XE:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
DWD024S-XE
VARIABLE SPEED REVERSIBLE PERCUSSION DRILL

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWD024S-XE

Summary of Contents for DeWalt DWD024S-XE

  • Page 1 INSTRUCTION MANUAL DWD024S-XE VARIABLE SPEED REVERSIBLE PERCUSSION DRILL...

  • Page 3: Definitions: Safety Guidelines

    The term “power tool” in the warnings refers to your mains-operated (corded) power Definitions: Safety Guidelines tool or battery-operated (cordless) power tool. 1) WORK AREA SAFETY The definitions below describe the level of severity for each signal a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. word.

  • Page 4: Electrical Safety

    b) Use personal protective equipment. Always wear eye protection. Protective operation. If damaged, have the power tool repaired before use. Many equipment such as dust mask, non-skid safety shoes, hard hat, or hearing accidents are caused by poorly maintained power tools. protection used for appropriate conditions will reduce personal injuries.

  • Page 5: Additional Safety Instructions For Drills

    • Avoid prolonged contact with dust from power sanding, sawing, grinding, Additional Safety Instructions for Drills drilling, and other construction activities. Wear protective clothing and wash • Wear ear protectors. Exposure to noise can cause hearing loss. exposed areas with soap and water. Allowing dust to get into your mouth, eyes, •...

  • Page 6: Assembly And Adjustments

    Hold tool with both hands to maximize control. A side handle comes assembled with the DWD024S-XE. The side handle (G) can be adjusted to suit both right-hand and left-hand users. TO ADJUST THE SIDE HANDLE 1.
  • Page 7 Keyless Chuck (fig. 1, 3–5) To reverse the motor, release the trigger switch FIRST and then push the lever to the The DWD024S-XE features a keyless chuck (D) right (viewed when holding the drill in the operating position). for greater convenience.

  • Page 8: Operation

    KEYLESS CHUCK REMOVAL (FIG. 3) WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in Tighten the chuck around the shorter end of a hex key (not supplied). Using a soft anticipation of a sudden reaction. hammer or piece of wood, strike the longer end in the counterclockwise direction. Proper hand position requires one hand on the main FIG.

  • Page 9: Maintenance

    Cleaning 7. With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once when the hole is deep enough to drill without the bit skipping out.
  • Page 10 For warranty repair information, call (AUS) 1800 654 155 or (NZ) 0800 339258. This warranty does not apply to • Accessories • Damage caused where repairs have been made or attempted by others. • Damage due to misuse, neglect, wear and tear, alteration or modification. This warranty gives you specific legal rights and you may have other rights under the provisions of the Consumer Guarantee Act 1993 (New Zealand only), Trade Practices Act 1974 and State Legislation (Australia only).
  • Page 12 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (AUG09) Part No. N038907 DWD024S-XE Copyright © 2009 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;...

Table of Contents