The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1. A specially instructed person should do servicing operation of the apparatus. DEH-1300MP/XNUC...
Page 3
CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions. DEH-1300MP/XNUC...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-1300MP/XNUC...
4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. area and a heat sink becomes hot areas. Be careful not to burn yourself. DEH-1300MP/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DEH-1300MP/XNUC...
See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted DEH-1300MP/XNUC...
3.2 PCB LOCATIONS CD Core Unit (S11.1Comp) Tuner Amp Unit Keyboard Unit A : DEH-1300MP/XNUC B : DEH-1350MP/XNES C : DEH-1350MP/XNES1 D : DEH-1350MPG/XNES E : DEH-1350MP/XNCN5 F : DEH-1390MP/XNID Unit Number QWM3162(A) QWM3163(B,C,D,F) QWM3164(E) Unit Name Tuner Amp Unit...
CD Mechanism Module 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-1300MP/XNUC...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW <- H Pin 15 Completes power-on operation. (After that, proceed to each source operation) DEH-1300MP/XNUC...
Cause: Ejection rotation retrial failure error Details: This error occurs when automatic loading was successful after ejection rotation retrial has failed (twice). Mecha Disc loading error Cause: Disc loading cannot be completed. -> Foreign substances were inserted. Disc was caught. DEH-1300MP/XNUC...
Page 21
EJECT does not work. The error state can be recovered only by turning off and on the ACC. *When determining a power supply error, please refer to the error mode (0xFB) only. (You do not have to refer to the Error code 0xA0.) DEH-1300MP/XNUC...
” key Color of key illumination : Lit in a color set as an initial value for single illumination. Lit in a changed color for dual illumination. Press “ ” key : All off Icons *Only 14-seg display is lit. DEH-1300MP/XNUC...
Page 24
The lighting of all segments is turned on. The lighting of all segments including icons is turned on. On (an initial value or All on setting value of default menu) Switch to "Usual update of display" by pressing “ ” + “ ” keys simultaneously. DEH-1300MP/XNUC...
Page 25
The lighting of all segments is turned on. On (an initial value or The lighting of all segments including icons is turned on. setting value of default All on menu) Switch to "ROM correction information is displayed" by pressing " " + " " keys simultaneously. DEH-1300MP/XNUC...
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. • Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-1300MP/XNUC...
Lift off the Tuner Amp Assy from the Heat sink side. The Tuner Amp Unit is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. CD Mechanism Module Fig.4 DEH-1300MP/XNUC...
Page 28
Remove the two screws. Straighten the tabs at two locations indicated and then remove the Tuner Amp Unit. Fig.5 Tuner Amp Unit Attention of removing (Fig.6) Don't remove this screws excluding the dismantlement of the CD Mechanism Module. Fig.6 DEH-1300MP/XNUC...
Page 29
1. Attach the button from the front side of the panel. Fig.9 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. Hitch the spring to the groove. Fig.10 DEH-1300MP/XNUC...
Page 30
Fig.11 Solder temp. : 360 ± 20 C Note: Soldering of the part shown in the figure must be done after fixing the Tuner Amp Unit to the bottom chassis. DEH-1300MP/XNUC...
Page 31
2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) Correct way of holding the unit Incorrect way of holding the unit DEH-1300MP/XNUC...
Page 32
1. Create an empty clamp state according to “How to create empty clamp state of mecha module”. 2. Apply 1.5 V to the CRG motor and move the PU to the outer circumference. (Caution) After moving the PU to the outer circumference and performing necessary treatment, make sure to solder the lead wires. DEH-1300MP/XNUC...
20 seconds while the time to return to due to mistaken eject operation, reset the product or the normal mode is maximum 40 seconds approximately. turn off and on the ACC to restore it. Make sure to check the sound quality in the normal operation mode. DEH-1300MP/XNUC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-1300MP/XNUC...
Check that square wave of 1 Hz is output from BU_HSFLG (43 Pin) of IC601 by flipping TEST IN (112 Pin) of the same IC601 to ‘H’ while the product is operating normally (when stand-by state is released with ACC on). If clock signal is out of this range, this resonator (X601) must be changed for a new one. DEH-1300MP/XNUC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING DEH-1300MP/XNUC...
Page 39
CEG-127 16-3 Service Network See Contrast table (2) Screw See Contrast table (2) Screw TRZ50P080FTC (2) CONTRAST TABLE DEH-1300MP/XNUC, DEH-1350MP/XNES, DEH-1350MP/XNES1, DEH-1350MPG/XNES, DEH-1350MP/XNCN5 and DEH-1390MP/XNID are constructed the same except for the following: Mark Description DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 Polyethylene Bag...
Page 41
QBH3001 Cover CNS7068 Label See Contrast table (2) Cover QNM3029 Panel QNS3126 (2) CONTRAST TABLE DEH-1300MP/XNUC, DEH-1350MP/XNES, DEH-1350MP/XNES1, DEH-1350MPG/XNES, DEH-1350MP/XNCN5 and DEH-1390MP/XNID are constructed the same except for the following: Mark Description DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 Tuner Amp Unit QWM3162 QWM3163...
CD LSI , RFAMP , CPU S903:DSCSNS SWITCH..ON-OFF PGND Actuator , Motor Driver AGND Audio These GND's are not connected to each other on PCB. PGND is connected to a floating mechanism part by a screw. The underlined indicates the switch position. DEH-1300MP/XNUC...
500 µs/div RFAGC 500 mV/div 500 mV/div 500 mV/div 500 mV/div 500 mV/div Track Open waveform 1 Track Jump waveform 4 Tracks Jump waveform Ref : Ref : Ref : REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-1300MP/XNUC...
Page 59
12 cm CD Eject operation Ref : Ref : Ref : AGND Mode: Mode: Mode: Normal Normal Normal RFAGC 1 V/div 500 µs/div 1 V/div 1 V/div 1 V/div Black dot (800 µm) during play Ref : REFO Mode: Normal DEH-1300MP/XNUC...
IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Q 803 (A,117,42) Transistor LSA1576UB A : DEH-1300MP/XNUC Q 921 (A,127,106) Transistor LSC4081UB B : DEH-1350MP/XNES D 301 (A,97,128) Diode CRG03...
Page 69
(A,118,70) CKSSYB104K10 R 689 (A,98,75) RS1/16SS0R0J R 702 (A,94,74) RS1/16SS221J C 607 (A,122,71) CKSSYB104K10 C 609 (A,134,67) CKSSYB331K50 R 704 (A,96,49) RS1/16SS221J C 610 (A,139,44) Capacitor CEVW101M4 R 708 (A,93,50) RS1/16SS104J C 611 (A,134,65) CKSSYB331K50 R 751 (A,141,134) RS1/4SA271J DEH-1300MP/XNUC...
Page 70
: Keyboard Unit R 1811 (B,51,12) (A,B,C) RS1/4SA272J (B,51,12) (D,E,F) RS1/4SA561J MISCELLANEOUS R 1812 (B,17,19) (A,B,C) RS1/4SA272J (B,17,19) (D,E,F) RS1/4SA561J IC 1801 (B,86,24) IC PD6340A IC 1802 (A,156,23) Remote IC GP1UXC14RK R 1813 (B,57,24) RS1/10SR0R0J D 1801 (A,68,22) White LED SMLXA4WBETW1(Z1) DEH-1300MP/XNUC...
Page 71
R 240 (B,50,11) RS1/16S473J R 241 (B,50,12) RS1/16SS103J R 244 (B,28,29) RS1/16SS473J R 254 (A,20,23) RS1/16SS104J R 256 (A,19,23) RS1/16SS104J R 259 (A,13,24) RS1/16SS0R0J R 291 (B,17,45) RS1/16SS272J R 307 (A,61,34) RS1/16SS183J R 308 (A,61,36) RS1/16SS183J R 309 (A,59,34) RS1/16SS183J DEH-1300MP/XNUC...