Related Manuals for DeWalt D25413-XE
Summary of Contents for DeWalt D25413-XE
- Page 1 INSTRUCTION MANUAL D25413-XE, D25414-XE, D25415-XE, D25430-XE 32 mm (1-1/8") HEAVY DUTY ROTARY HAMMER...
-
Page 3: Definitions: Safety Guidelines
CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ). Drilling into metal Technical Data Vibration emission <2.5 <2.5 <2.5 – value a D25413-XE D25414-XE D25415-XE D25430-XE Uncertainty K = – Voltage Drilling into concrete Power Input 1000 1000 1000... -
Page 4: Safety Instructions For Power Tools
The vibration emission level given in this information sheet has been measured in 1) WORK AREA SAFETY accordance with a standardised test given in EN 60745 and may be used to compare a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. one tool with another. -
Page 5: Electrical Safety
c) Prevent unintentional starting. Ensure the switch is in the off position g) Use the power tool, accessories and tool bits, etc. in accordance with before connecting to power source and/or battery pack, picking up or these instructions, taking into account the working conditions and the work carrying the tool. - Page 6 • Hold power tools by insulated gripping surfaces when performing an WARNING: We recommend the use of a residual current device with a residual operation where the cutting accessory may contact hidden wiring or its own current rating of 30mA or less. cord.
-
Page 7: Components (Fig. 1)
B. Main handle G. Mode selection dial C. Side handle H. Mode selector button D. Depth rod I. Reversing lever (only D25413-XE, D25414-XE & (only D25413-XE, D25414-XE & D25415-XE) D25415-XE) E. Depth rod release button J. Handle shocks INTENDED USE... - Page 8 A side handle comes assembled with this rotary HAMMERDRILL MODE (ONLY FOR D25413-XE, D25414-XE & D25415-XE) hammer. The side handle (C) can be fitted to suit both To use hammerdrill mode, press the mode selector button (H) and turn the right-hand and left-hand users.
-
Page 9: Operation
Depth Rod (Fig. 7) WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) (ONLY FOR D25413-XE, D25414-XE & D25415-XE) by gripping the front part of the chuck and turning the tool on. Damage to the chuck TO ADJUST THE DEPTH ROD and personal injury may occur. - Page 10 WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly with both hands to control the twisting action and avoid (ONLY FOR D25413-XE, D25414-XE & D25415-XE) injury. The reversing lever (H) is used to reverse the rotary hammer for backing out fasteners 6.
-
Page 11: Maintenance
32 mm (1-1/8") brushes wear out. This prevents serious damage to the motor. New brush assemblies Optimum Capacity 13 to 25 mm (1/2" - 1") Concrete are available at authorized DeWalt service centers. Always use identical replacement No-load BPM 0-4,700 parts.Lubrication... - Page 12 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (DEC13) Part No. N362624 D25413-XE, D25414-XE, D25415-XE, D25430-XE Copyright © 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...