Page 1 AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOL TAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING. REFER TO BACK COVER FOR IMPOR T ANT SAFETY GUIDELINES Published by Philips Consumer Lifestyle Copyright reserved Subject to modification May 10 2011...
Page 2: Important Safety Notice
SERVICE MANUAL. recommended by Philips must f irst sati sfy himself thoroughly that neither his safety nor the saf e operation of the equipment will be jeopardized by the service method sel ected.
Page 3: Technical Data
BDL4651VH LCD Technical Data AUO Panel Interface Requirement LCD Vendor LCD Panel P460HW02 V0 LCD size 46” inch Configuration Display Resolution 1920(H) x 1080(V) External Connector Input Output Pixel Pitch 0.53025 mm R/L 178 degree (min)/ UD178 Viewing Angle Power (AC) degree (min) Display Response...
Page 4: Installation
BDL4651VH LCD Installation FRONT VIEW - off when the main power of the display is turned off 7. Smart Insert installation holes Location for the Smart Insert (for integration of a small form factor PC) and M4 screws. (Maximum load: 2kg) 8.
Page 5 BDL4651VH LCD Installation Remote Control UP button POWER button • To move the highlight bar up to adjust the selected item when OSD Press to switch on the monitor from menu is on. standby mode. Press again to turn it off •...
Page 6 BDL4651VH LCD Installation CONNECTING EXTERNAL EQUIPMENT (DVD/VCR/VCD) USING HDMI INPUT USING COMPONENT VIDEO INPUT 1. Connect the green-colored (labeled as "Y") jack of the device to the Connect the HDMI connector of the external device to the HDMI input of green-colored "Y"...
Page 7: Installation
BDL4651VH LCD Installation USING HDMI INPUT CONNECTING ANOTHER BDL4230E MONITOR 1. Connect the DVI-D connector of the PC to the HDMI connector of the You can interconnect multiple BDL4651VH units to create a daisy-chain display using a DVI-HDMI cable. configuration for applications such as a video wall. Note: The number 2.
Page 8: Troubleshooting
BDL4651VH LCD Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back 2. Make sure the power switch is switched on. of the display is not switched on.
Page 9: On Screen Display
What is the On-Screen Display? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display...
Page 10: Screen Menu
BDL4651VH LCD On-Screen Display Screen Menu CUSTOM ZOOM Note: This item is only available when Zoom mode is set to Custom. You can use this function to further customize the zoom settings to suit the image you want to display. Use the UP/DOWN button to toggle between the following items, and use the PLUS/MINUS button to adjust.
Page 11: Pip Menu
BDL4651VH LCD On-Screen Display AUDIO MENUAU PIP MENU DIOVOLUMEMUTEAUDIO Notes: • For Component, VGA, DVI-D and HDMI inputs only. • For Full and Normal zoom modes only. • The PIP function is turned off by default. Press the PIP ON/OFF button on the remote control to turn on PIP and make it accessible from the OSD menu.
Page 12 BDL4651VH LCD On-Screen Display CONFIGURATION 1 MENUCONFIGURATION COLOR SYSTEM Note: For Video and S-Video inputs only. Select the color system depending on the input video format. Use the UP/DOWN button to make selection. • AUTO • PAL 4.43 • PAL 3.58 •...
Page 13: Advanced Option
BDL4651VH LCD On-Screen Display • Off - Disable the film mode frame conversion function. This mode is ADVANCED OPTION MENUADVA NCED suitable for TV broadcasting and VCR signals. IR CONTROL Select the operation mode of the remote control when multiple BDL4651VH units are connected via RS232C cables.
Page 14: On Screen Display
BDL4651VH LCD On-Screen Display SCHEDULE 11. Press the EXIT button and the menu will close and the schedule Note: We recommend setting up current date and time in Date and time settings will take effect. To set up more schedule items, repeat the steps before using the Schedule function above except that a different schedule item should be selected (schedule This function allows you to program up to seven different scheduled time...
Page 15: Philips Pixel Defect Policy
PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or reference table. If the LCD screen is within specification a warranty sub-pixel defects exceeding the tolerances listed in the following table.
Page 16: Mechanical Instructions
BDL4651VH LCD Mechanical Instruction Preparation before disassemble 1. Clean the room for disassemble 2. Identify the area for monitor 3. Check the position that the monitors be placed and the quantity of the monitor; prepare the area for material flow; according to the actual condition plan the disassemble layout 4.
Page 17: Mechanical Instructions
BDL4651VH LCD Mechanical Instruction Item picture Operation Tool Notes Disassemble the power BD and speaker holder from display Æ 10-M3 screws Electric screw drive #2 Disassemble the power bkt from display Æ 2-M3 screws Electric screw drive #2 Disassemble the fan and IR transfer BD from power bkt.
Page 18: Color Adjustment
BDL4651VH LCD Color Adjustment Color adjustment more information see Fig. 7.1 . When VDDB =24V,IDDB = 8.5 A. (1) Input source set the YPbPr (VGA / DVI / HDMI) input LWH=Lon1, Where Lon1 is the luminance with all pixels displaying (2) After ADC Calibration (3) Set the picture mode to standard mode at user OSD white at center 1 location.
Page 19: Color Adjustment
BDL4651VH LCD Color Adjustment Color temp item CVBS1 / CVBS2 / VGA / YPbPr / (3) Table 2 : default value of internal gain RGB drive & offset: @factory OSD S-VIDEO DVI / HDMI Color temperature 9300qK 9300qK Color temp item CVBS1 / CVBS2 / VGA / YPbPr / Red drive...
Page 20 BDL4651VH LCD Electrical characteristics In/Out Terminals General Internal Speaker...
Page 21 BDL4651VH LCD Timing requirement MODE ASPECT RATIO HANDLING AR Aspect STANDARD RESOLUTION FS*Full-Screen Ratio Composite S-Video YPBPR HDMI VESA 640x480 @ 60Hz 1366X768 16:09 VESA 640x480 @ 72Hz 1366X768 16:09 VESA 640x480 @ 75Hz 1366X768 16:09 720x400 @ 70Hz 1366X768 16:09 VESA 800x600 @ 60Hz...
Page 22: White Balance
BDL4651VH LCD White balance The picture color temperature shall be able to be chosen out of 5 modes 10000K, 9300K, 6500K, 5800K, and USER. 10000K, 9300K, 6500K, 5800K are factory setting (fixed color) and “USER” is adjustable mode. (The default color of “USER” mode is the same color as 6500K mode.) A/D converter calibration of the scalar shall be performed with 0V/0.730Vp-p black/white level signal to obtain adequate dynamic range for video signal output level deviation.
Page 23: Service Tool
BDL4651VH LCD Service tool-Hardware F/W Writing Tool: RS232 Cable: Description 5K.0R505.501 CABLE D-SUB 9/9P UL20276 11M EDID Writing Tool: USB Cable and Jig BD Description 5K.L1E03.501 Service Tool-Cable-VOARD (CABLE USB 2.0A/B B-PVC 1.8M) 5E.0RC38.001 Service Tool-Board-VOARD (PCBA JIG BD MI WP42SF0)
Page 24: Service Tool
BDL4651VH LCD Service tool-Software FW writing tool: Pixelworks ImageProcessor SDK FlashUpgrader EDID writing tool : RTD_CustomerTool_V1.
Page 25: Ddc Instructions
BDL4651VH LCD DDC Instructions DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed "Analog DDC IC, Digital DDC IC & EEPROM". It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.
Page 26 BDL4651VH LCD DDC Instructions 3. Follow the installed steps and press ＂NEXT＂ to Install Driver 4. When setup has finished, restart computer...
Page 27 BDL4651VH LCD DDC Instructions 5. Prepare the download equipment. - Use USB cable connect to PC and Tool Board - Use VGA cable connect to Tool Board and Display PC or NB VGA cable for EDID writing need to be removed pin5 to disable EDID write protect Display 6.
Page 28 BDL4651VH LCD DDC Instructions 7. Update EDID – select “EDID Update” Communication – select “USB”, ISP Type – select “Serial Flash” For EDID Updated...
Page 29 BDL4651VH LCD DDC Instructions 8. EDID upload(VGA) – EDID length select and then press to select EDID file and then press to write EDID into display 128B for VGA Open EDID file To write EDID...
Page 30 BDL4651VH LCD DDC Instructions (Power off status and LED: Red) 9. EDID upload(DVI)-EDID length select and then press to select EDID file and then press to write EDID into display 128B for DVI Open EDID file To write EDID...
Page 31 BDL4651VH LCD DDC Instructions (Power off status and LED: Red) 10. EDID upload(HDMI) – EDID length select and then press to select EDID file and then press to write EDID into display 256B for VGA Open EDID file To write EDID 11.
Page 32: Ddc Instructions & Serial Number
BDL4651VH LCD DDC Instructions Serial Number Definition...
Page 33: Ddc Data
BDL4651VH LCD DDC DATA Analog DDC HDMI DDC 00 FF FF FF FF FF FF 00 41 0C 0B D2 00 00 00 00 00 FF FF FF FF FF FF 00 01 14 01 03 08 65 39 78 41 0C 0B D2 00 00 00 00 EA 6A F8 A3 55 49 9A 24 01 14 01 03 80 65 39 78...
Page 34: Firmware Upgrade For Cpu
BDL4651VH LCD Firmware Upgrade for CPU 1. Preparation: 1.1 Tool: Download cable( RS232 cable connect between PC/Notebook with tool board ) #RS232 is RXD and TXD interlaced line Personal computer or Notebook Download tool program “Pixelworks ImageProcessor SDK FlashUpgrader”. 1.2 Firmware files 2.
Page 35 BDL4651VH LCD Firmware Upgrade for CPU 3. Show the Pixelworks ImageProcess K FlashUpgrader picture. #The Connection, COM Port in accordance with user by oneself PC/NB choose. #The Notify On Completion in accordance with user by oneself PC/NB choose. 4. The RS232 Download cable insert RS232 INPUT pin. 5.
Page 36 BDL4651VH LCD Firmware Upgrade for CPU 6. The key change to cancel after Press Flash key, 7. The Power code cable insert. 8. The pixelworks ImageProcess or SDK FlashUpgrader program download start.
Page 37: Firmware Upgrade For Cpu
BDL4651VH LCD Firmware Upgrade for CPU 9. The firmware download will finish after about 5 minutes. 10. Please press “確定”. Download program finish. 11. Please pull out Power code, RS232 Download cable.
Page 38: Failure Mode Of Panel
38 B DL4651V H LC D Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel.
Page 39: Wiring Diagram
BDL4651VH LCD Wiring Diagram Power wire system B403 B402 B401 Panel B301 Main BD AC 100~220V IN...
Page 40: Wiring Diagram
BDL4651VH LCD Wiring Diagram Signal wire system Panel J13,J17 For Fan Module Main BD Keypad BD Audio BD IR BD IR-Trans BD...
Page 41: Block Diagram
BDL4651VH LCD Block Diagram Speaker 12W*2 YPbPr Audio Amp Audio In TPA3004 Power PCB Audio Switch PC Audio In CVBS-1 Power Audio PCB Audio In Dimmer Sensor TI PCM1754 YPbPr ABL PCB YPbPr In D-Sub In D-Sub Out D-Sub Repeater ADI ADA4859 HDMI In *2 TMDS...
Page 42: Block Diagram
BDL4651VH LCD Block Diagram...
Page 43 Scalar Diagram & C.B .A B DL4651V H LC D 43 R 470 3. 3K D 1 V 8 R 472 750 I 2C Pul l hi g h D 3 V 3 R 415 22 J L S C L R 416 22 J L S D A HDMI...
Page 44 44 B DL4651V H LC D Scalar Diagram & C.B .A T P 225 I N T 9125_ I NT HD MI_ S C DT R 419 100 D3V 3 D3V 3 HD MI_ S C DT HD MI_R S T 6,11 HD MI_R S T T P 42...
Page 45 B DL4651V H LC D 45 Scalar Diagram & C.B .A P 3 V 3 ANAL OG I N DI GI TAL I N R 5 72 R 5 73 R M I 0 4.7K 4.7K C 176 0. 047U K R M U X SDA_CCM C VB S 2...
Page 46 46 B DL4651V H LC D Scalar Diagram & C.B .A V DC _R S Tn D3V 3 R E S E A C 15 Cha nge c om ponent A E 1 A F 16 R 242 R 243 R 244 R 245 R 246...
Page 47 Scalar Diagram & C.B .A B DL4651V H LC D 47 D2V5 R 3 09 M V R E F 1K F R 3 10 C 212 C 213 C 214 1K F 0. 1 U K 0. 1 U K 0.
Page 48 Scalar Diagram & C.B .A 48 B DL4651V H LC D R 3 47 100K R 3 48 R 3 49 *N C _ 14. 3 18M H Z T P 196 P O R T 2_ V S P O R T 2_ V S C 330 C 331...
Page 49 B DL4651V H LC D 49 Scalar Diagram & C.B .A add CL68/ CL67, Change CG13 CG14, M odi f y 1. 8VA_PW 20080312 EI LEEN P u t CG13 & CG14 0. 1UF c l os e t o PW 106B/ 328B L a y out Key Poi nt D 1V 8 A 1 V 8...
Page 50 Scalar Diagram & C.B .A 50 B DL4651V H LC D...
Page 51 Scalar Diagram & C.B .A B DL4651V H LC D 51...
Page 52: Power Diagram & C.b.a
BDL4651VH LCD Power Diagram & C.B.A...
Page 53 BDL4651VH LCD Power Diagram & C.B.A...
Page 54: Power Diagram & C.b.a
BDL4651VH LCD Power Diagram & C.B.A...
Page 55: Control Diagram & C.b.a
Control Diagram & C.B .A. B DL4651V H LC D 55 S W 1 T P 1 T P 2 S W 2 S K R P AB E 010 L E D 1 T P 3 68 F T P 4 S K R P AB E 010 R E D /G R N T P 5...
Page 56: Control Diagram & C.b.a
Control Diagram & C.B .A. 56 B DL4651V H LC D...
Page 57: General Product Specification
BDL4651VH LCD General Product Specification Product Identification 46” BDL LCD DISPLAY BDL4651VH/00 Issued by: Technical Marketing Manager Larry Yang...
Page 58: Table Of Contents
BDL4675XU LCD General Product Specification Table of Contents SCOPE.................................. 61 1.1 G ENERAL RODUCT EATURES ..........................61 1.2 P RODUCT ANGE ..............................61 ELECTRICAL REQUIREMENTS ........................62 2.1 S TANDARD ESTING ONDITIONS ........................... 62 2.2 V IDEO UDIO NPUT IGNALS ..........................
Page 59 BDL4651VH LCD General Product Specification 6.2 R EMOTE ONTROL ..............................96 6.3 DFU ..................................96 6.4 Q UICK UIDE ..............................96 6.5 W ARRANTY CARD ..............................97 6.6 O THERS ..................................97 MECHANICAL..............................97 7.1 C OSMETIC ................................97 7.2 M ECHANICAL ILES ............................
Page 60 BDL4675XU LCD General Product Specification DOCUMENT REVISION HISTORY Revision no. Date Description V1.0 2010/01/05 Release V2.0 2011/5/16 Release...
Page 61: Scope
• Fault diagnostics • Advanced anti image sticking • Automatic Long Cable Compensation • PIP support • Scheduling 1.2 Product Range Display Destination Mains Cord Cabinet Color BDL4651VH/00 EU, UK Generic Black BDL4651VH/00 Generic Black BDL4651VH/00 Turkey EU, UK Generic Black BDL4651VH/00...
Page 62: Electrical Requirements
BDL4675XU LCD General Product Specification 2. ELECTRICAL REQUIREMENTS All performance specifications are defined under “STANDARD TESTING CONDITIONS”, unless otherwise specified. Standard Testing Conditions • ≥ 30 min. Warm up time - • 15°C ~35 °C. Ambient temperature - • Ambient light - 400-600 lux •...
Page 63 BDL4651VH LCD General Product Specification Req. ID Resolution according to VESA DMT standard Specification Resolution Refresh Horizontal Pixel Clock Standard Type Original Rate Frequency Document Date PCRES4 640 x 480 60 Hz 31.5 kHz 25.175 MHz Industry Standard n/a PCRES5 640 x 480 72 Hz 37.9 kHz 31.500 MHz VESA Standard VS901101...
Page 64: Av Input Signal Requirements
BDL4675XU LCD General Product Specification Audio input - Sensitivity 500mVrms, the amplifier outputs full power when the input level reaches 500mVrms, terminated with impedance >10kΩ. Lineout output - Stereo, 2Vrms output. Speaker output - 2 x 12 Wrms back firing speakers, with T.H.D. < 10%. 2.2.2 AV input signal requirements CVBS input -...
Page 65: Ddc Channel
BDL4651VH LCD General Product Specification Pixel encodings: RGB 4:4:4, YCbCr 4:2:2, YCbCr 4:4:4. Audio sample rates: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96kHz, 176.4 kHz, 192 kHz. Audio channels: up to 8. DDC channel: Allows source to interrogate capabilities of sink. I²C signaling with 100 kHz clock.
Page 66 BDL4675XU LCD General Product Specification EDID content for HDMI 00 FF FF FF FF FF FF 00 41 0C 05 D2 01 01 01 01 01 13 01 03 80 5D 34 78 EA 60 D7 A3 55 4A 9B 24 10 47 4A AD 4A 00 81 80 81 40 D1 00 A9 40 81 00 01 01 01 01 01 01 02 3A...
Page 67: Service Mode
BDL4651VH LCD General Product Specification The following DDC/CI commands should be supported via command line: Commands Set Brightness Set Contrast Set Red Gain Set Green Gain Set Blue Gain Get Brightness Get Contrast Get Red Gain Get Green Gain Get Blue Gain Service mode Detailed technical specification refers to Service delta technical specs.
Page 68: User Control Interface
BDL4675XU LCD General Product Specification Recovery from DPM - Power & function recover when either H & V syncs or digital clock are detected. Standby - The Display enters “AV standby mode” when it’s switched off by RC. “Standby/Power” key or SLEEP TIMER function is activated or no AV signal input for 15 seconds.
Page 69 BDL4651VH LCD General Product Specification...
Page 70: Front Controls
Receiver for Display control, transmitter for ITV data cloning. Operation Angle RC operational distance ≥ 10m 0° (for H & V) ≥ 10m 30° (for H & V) ≥ 10m 45° (for H only) • Remote Control – Philips protocol. Philips protocol is used for remote control communication.
Page 71 BDL4651VH LCD General Product Specification...
Page 72 BDL4675XU LCD General Product Specification...
Page 73 BDL4651VH LCD General Product Specification RC key definition: Remote Key Key Name Data Code POWER 0x03 VIDEO SOURCE 0x01 AUDIO SOURCE 0x1E SMART 0x1D SIZE 0x29 PIP ON/OFF 0x24 PIP INPUT 0x25 PIP CHANGE 0x26 CONTRAST 0x27 BRIGHTNESS 0x28 MENU 0x20 0x15 DOWN...
Page 74 BDL4675XU LCD General Product Specification PICTURE MENU OVERVIEW...
Page 75 BDL4651VH LCD General Product Specification...
Page 76 BDL4675XU LCD General Product Specification SCREEN MENU...
Page 77 BDL4651VH LCD General Product Specification...
Page 78 BDL4675XU LCD General Product Specification AUDIO MENU...
Page 79 BDL4651VH LCD General Product Specification PIP (PICTURE IN PICTURE) MENU...
Page 80 BDL4675XU LCD General Product Specification...
Page 81 BDL4651VH LCD General Product Specification CONFIGURATION 1 MENU...
Page 82 BDL4675XU LCD General Product Specification...
Page 83 BDL4651VH LCD General Product Specification CONFIGURATION 2 MENU...
Page 84 BDL4675XU LCD General Product Specification ADVANCED OPTION MENU...
Page 85 BDL4651VH LCD General Product Specification...
Page 86 BDL4675XU LCD General Product Specification...
Page 87 BDL4651VH LCD General Product Specification...
Page 88 BDL4675XU LCD General Product Specification...
Page 89: I /O Connectors
BDL4651VH LCD General Product Specification 2.7 I /O Connectors Connectivity overview: Rear connectors: • Power input: 3-pin IEC-320-C13 socket mains AC in. • AC switch: Mains switch at line. • PC input: 15 pins VGA D-Sub Female connector with lime green 3.5mm Mini-jack audio stereo connector.
Page 90 BDL4675XU LCD General Product Specification VGA D-Sub connector pin assignment: Signal Signal Assignment Assignment Red video Green video Blue video Red GND Green GND Blue GND +5V (Supply from PC for DDC circuit) Sync GND DDC serial data H-sync V-sync DDC serial clock •...
Page 91: Visual Performance
BDL4651VH LCD General Product Specification VISUAL PERFORMANCE LCD Module Characteristics First Panel Vendor Panel Type Number P460HW02 Module Dimensions 1048.4mm(H) x 605.0mm (V) x 57.8mm (D) (mm) Display Area (H x V) 1018.08(H) x 572.67 (V) Aspect Ratio 16:9 1920x1080 Pixel Format Pixel Pitch (mm) 0.53025mm...
Page 92: Functional Requirements
BDL4675XU LCD General Product Specification Picture centering - H & V ≤ 0.5 %. (for 480i/p, 576i/p, 720p, 1080i/p) Over scan - ≤ 3 % (top) & ≤ 3 % (bottom) for Display, 480i, 576i ≤ 3% (left) & ≤ 3 % (right) for Display, 480i, 576i ≤...
Page 93: Wide Screen Signalling Bit (Wssb) Picture Size
BDL4651VH LCD General Product Specification 4.2.1 Wide Screen Signalling Bit (WSSB) picture size CVBS input must support WSSB function. 4.2.2 Picture format There are 6 picture formats: FULL, NORMAL, DYNAMIC, CUSTOM, REAL and 21:9. FULL NORMAL DYNAMIC 21:9 4.2.3 Picture in Graphics PIP Specification Input HDMI...
Page 94: Pc Picture Auto Adjustment Function
BDL4675XU LCD General Product Specification PC Picture Auto Adjustment Function ----- D-Sub input Perfect Front Of Screen after auto adjustment. Perfect FOS : Full Screen, w/o flash & unstable status at any picture. When a new VGA source is detected, then automatically an auto adjustment should be performed.
Page 95: Smart Power
BDL4651VH LCD General Product Specification Smart Power This function allows you to choose a certain level of power saving condition: “OFF”: to set the system in normal power condition “MEDIUM”: to set the system in medium level power saving status. “HIGH”: to set the system in high level power saving status Smart Power Setting Display Brightness...
Page 96: Life Time Indication (Show On Osd Menu To Be Defined)
BDL4675XU LCD General Product Specification 5.4 Life time indication (show on OSD menu to be defined) Burn-in hour reporting based on generic service requirements for OEM (D04.1) + study of data- sheets 5.5 External communication 5.5.1 Timing between each message should be a minimum of 500 ms 5.5.2 There should be a menu selection ( e.g.
Page 97: Warranty Card
BDL4651VH LCD General Product Specification Warranty card 6.6 Others Saddle 7. MECHANICAL Cosmetic Qisda ID - Mechanical Data Files Provide mechanical drawings with key dimensions.
Page 98: Location Of Philips Logo
BDL4675XU LCD General Product Specification Location of Philips Logo...
Page 99: Location Of Icons
BDL4651VH LCD General Product Specification Location of Icons 7.5 Color for Resin / Paint Black 30% gloss front/Silver brush gloss decoration part/Stealth Black in mould back-cover. Resins • RoHS requirements. • WEEE requirements. • PC+ABS • China Rohs required. ( sales in China only) 7.7 Paint Used •...
Page 100: Plastics Flammability
All major plastic parts (bezel, back cover, base) need to be molded from same resin. Base / Pedestal otherwise specified. No plastic parts 7.10 Texture/Glossing of Housing • The texture area and texture no should follow Philips make-up sheet. • The exterior surfaces shall have a uniform texture. • Philips must approve the mold texturing.
Page 101: Label
BDL4651VH LCD General Product Specification 7.14 Label • Regulatory label / Carton label should follow Philips requirement. • Detail document refer to Philips Engineering Reference Book. 7.15 Product Dimension / Weight • Unit dimension (without stand) - 1060(W)*660(H)*405(T)mm • Packed unit dimension (carton) - 1190 (Length)* 290(Width)* 754 ( Height) •...
Page 102: Pallet / Container Loading
BDL4675XU LCD General Product Specification 7.17 Pallet / Container Loading • Air shipment - 4 • Sea container 20'(pallet/slip sheet) - 62 • Sea container 40'(pallet/slip sheet) - 132 • Sea container 40' High Cube (pallet/slip sheet) - 160 • Container loading - 8.
Page 103: Altitude
BDL4651VH LCD General Product Specification 8.5 Altitude • Operating - 0 to 4500m • Storage - 0 to 9000m • Shipping - 0 to 9000m 8.6 Air pressure • Operating - 795 to 1013 mbar • Storage - 300 to 1013 mbar •...
Page 104 BDL4675XU LCD General Product Specification WEEE report and All EU WEEE Supplier declaration GB4943-2001 (IEC60950-1) CCC certificate Supplier GB9254-2008 (CISPR22) CCC certificate Supplier GB17625.1-2003 (IEC61000-3-2) CHINA GB21520-2008 CECP certificate Supplier CEL certificate AUSTRALIA AS/NZS3548:1995 / NEW- CB, EMC report AS/NZS CISPR22: 2002 Class B ZEALAND N23037 UL 60950-1: 2003...
Page 105: Emc Requirements
Restriction on the use of certain hazardous substances. Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Bipheny1 (PBB) and Polybrominated Bipheny1 Ether (PBDE)(flame retardant). WEEE Producer (Philips) responsible for retailer take back schemes and recycling. -- System implemented. -- Collection and recycle targets. Ongoing Regulatory There's a possibility that other regulatory certificates will be required during the life of the product.
Page 106: System Flow Chart
BDL4675XU LCD General Product Specification 10.1 System flow chart 10.2 Specification input and update The product specification shall be initiated by MMD and supported by concerned engineering department such as E/M/S, Safety/Approbation Group and DQE before RFQ. It must be updated in each product creation milestone.
Page 107 BDL4651VH LCD General Product Specification Supplier Model No. : Date : Milestone Philip v.s. Qisda EVT/DVT v.s. MMD Milestone EVT ; PVT v.s. Test Item EVT DVT EVT PVT PVT Front of screen tests Brightness/Contrast 1.1.1 Brightness control range 1.1.2 Contrast control range 1.1.3 Luminance uniformity...
Page 108 BDL4675XU LCD General Product Specification 1.3.11 Halation 1.3.12 Luminance loading 1.3.13 Pixel defects 1.3.14 Noise and self pollution 1.3.15 Microphony 1.3.16 High voltage regulation No need 1.3.17 Earth magnetic sensitivity No need 1.3.18 Local dooming No need 1.3.19 MANNHEIM effect No need 1.3.20 Interlacing...
Page 109 BDL4651VH LCD General Product Specification 2.18 Unweighted and filter 2.19 Headphone performance 2.20 Auxiliary In/out Level 2.21 Thermal click noise TV Front end and Remote control Tuner sensitivity Tuning range Interference on IF harmonics Search tuning behavious AFC catch in and holding range AGC overload Tuner/IF parameter Amplitude response to modulation frequency...
Page 110 BDL4675XU LCD General Product Specification Brown in voltage Brown out voltage Mains frequency Start up and off behavious Power dissipation 4.10 Current consumption 4.11 Gain and Phase margin 4.12 Output voltage and Cross regulation 4.13 Transient Response 4.14 Line and load regulation 4.15 Ripple and noise level 4.16...
Page 111 BDL4651VH LCD General Product Specification 5.27 PIP Function 5.28 Audio Test 5.29 Check Smart Control Function 5.30 EEPROM mapping after power on-off cycle 5.31 I2C Function Test 5.32 Display size control Function 5.33 Reset function 5.34 Zoom Function 5.35 Extra function key 5.36 BDS Serial Xpress communication test Design Quality and Reliability tests...
Page 112 BDL4675XU LCD General Product Specification Cold drop test Half-sine shock test Bump panel data Compression test vendor's report 8.10 Mechanical Aspect and Tests 8.10.1 Assembled stand (salt spray) 8.10.2 Stand base warpage Positioning (slant, assembly) 8.10.3 8.10.4 Stability (floor stand base) Stability (tilt over) 8.10.5 8.10.6...
Page 113 BDL4651VH LCD General Product Specification VGA: Req. ID Resolution according to VESA DMT standard Specification Resolution Refresh Horizontal Pixel Clock Standard Type Original Rate Frequency Document Date PCRES4 640 x 480 60 Hz 31.5 kHz 25.175 MHz Industry Standard n/a PCRES5 640 x 480 72 Hz 37.9 kHz...
Page 114 BDL4675XU LCD General Product Specification HDMI: Req. ID Resolution according to VESA DMT standard Specification Resolution Refresh Horizontal Pixel Clock Standard Type Original Rate Frequency Document Date PCRES4 640 x 480 60 Hz 31.5 kHz 25.175 MHz Industry Standard n/a PCRES5 640 x 480 72 Hz 37.9 kHz...
Page 115 BDL4651VH LCD General Product Specification Test Input VGA PC Input +Audio L/R VGA D-sub Component video 1 (HD/SD) + Audio L/R YPbPr(480i/p, 720p, 1080i, 1080p) VIDEO + Audio L/R x 1 S-VIDEO x 1 HDMI input with HDCP (version 1.3) x 2 HDMI with HDCP (480i/p, 576 i/p, 720p, 1080i, 1080p) EDID tables filled in for all supported PC and Video...
Page 116: Design Quality And Reliability Review And Validation Procedure
BDL4675XU LCD General Product Specification 10.5 Design quality and reliability review and validation procedure These are activities that should be executed by Supplier and MMD group per product creating process. Supplier must provide whole quality and reliability testing and evaluation report to DQE.
Page 117: Design Quality Review And Validation Evaluation Process
BDL4651VH LCD General Product Specification 10.6 Design quality review and validation evaluation process DQE will performs review and validation on the reports and activities of design quality and reliability evaluation in product creation process, which is performed by supplier. If necessary, supplier needs to provide third party verification and certification report.
Page 118 118 B DL4651V H LC D...
Page 119: Spare/ Recommended P Arts List
B DL4651V H LC D 119 Spare / Recommended parts list Spare parts change rule: Gray color: old parts can be ALT to new parts Gray color with delete line: old parts can not be used to this model Spare parts upgrade rule: last number +1 --> Latest version parts number Example old : 6K.0QC01.011...
Page 120: Pcba Photos
120 B DL4651V H LC D Panel & PCBA photos ITEM PCM Philips 12NC Description Photo 5F.MUQVV.011 LCDM46 P460HW02 V0 AUO CS.5J1FJ.001 PACK SKD MAIN BD EP46SF3 5D.0RC07.021 PCBA PWR BD 300W UP3003-01BG 9B.0VE02.QBU SKD ASSY KEY BD WP08SF0 9B.0WF05.013 SKD AUDIO BD EP65SF0 9B.14F11.001...
Page 121 BDL4651VH LCD 121 0. Warning All ICs and many other semi -conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can 1.4 Attachment of SMDs reduce life drastically . When repairing, make sure that you are - Locate the SMD on the solder lands by means of tweezers and solder connected with the same potential as the mass of the unit via a wrist the component on one side.
Page 122 IC data sheet. So as not to damage neighbouring components, it may be necessary to reduce some temperatures and times. More Information For more information on how to handle BGA devices, visit this URL: http://www.atyourservice.ce.philips.com (needs subscription). After login, select Magazine, then go to Workshop Information. Here you will find Information on how to deal with BGA-ICs.
Page 123: Repair Flow Chart
BDL4651VH LCD 123 Repair Flow Chart 1.Check wire cable connection between main System power ON? board and keypad 2.Check VCC 5V in Check wire cable connection between back Back light on light and power board Check which one is fail? Check U38 U39 U43 output voltage (1.8V,3.3V,2.5V) is correct 1.Check IR/Lign wire cable...
Page 124 124 BDL4651VH LCD Repair Flow Chart LCD Panel is no picture Keypad LED is ON? Check power is correctly? Power button operation is normal Check GPIO status Check GPIO status Check POWER ON control pin is High? Check input source and path is ready Check LCD12V and LVDS power sequence...
Page 125 BDL4651VH LCD 125 Repair Flow Chart RS232 link fail 1. Check control pin RS232_TXEN status Check U28 pin20 is high? (default high) 2. Check R520 or R491 is mouted? Check U28 pin19 is high? Check control pin RS232_SHDN status (default high) Check J22 pin RX and TX is normal ?
Page 126 126 BDL4651VH LCD Repair Flow Chart Audio output is no sound Check Audio board power 12V is correctly? Check control pin Check GPIO control pin (R277, R278) status AUDIO_SW_SE1’ 2 operation is normal Check mute pin Check GPIO control pin(R492) status AUDIO_VOL_ON is high or low To measure audio board U1 Check audio board U1 soldering or change...
Page 127 BDL4651VH LCD 127 Repair Flow Chart 1. Check Q9 Q10 R162 R163 R164 Keypad LED fail 2. Check P3V3 3. Check J11 soldering 1. Check P5V, P2V5, P3V3, P1V8 No OSD image 2. Check J25 PWRBD_ON and LCD_BRT_CTRL Signal 1. 1. Check L55, L56, L57, R22, R32, R38 No PC input (VGA) 2.
Page 128: Repair Flow Chart
128 BDL4651VH LCD Repair Flow Chart Check U1 operation normal? CVBS repeat output no signal Check U5 operation normal? VGA repeat output no signal Check U24 / U25 operation normal? DVI or HDMI picture display abnormal Check cable or change another IR board IR function fail Check Y4 waveform or U35 is operation Scheduling function fail...
Page 129: Safety Test Requirements
BDL4651VH LCD 129 Safety Test Requirements All units that are returned for service or repair must 3. Equipments and Connection pass the original manufactures safety tests. Safety 3.1. Equipments testing requires both Hipot and Ground Continuity For example : testing. - Zentech 9032 PROGRAMMABLE AUT O SAFETY HI-POT TEST INSTRUCTION TESTER...

Philips BDL4651VH/00 Service Manual

1 Scope

2 Electrical Requirements

3 Visual Performance

4 Functional Requirements

5 Non Functional Requirements

6 Accessories

7 Mechanical

8 Reliability / Environment

9 Regulatory Compliance

Quick Links

Related Manuals for Philips BDL4651VH/00

Summary of Contents for Philips BDL4651VH/00

Table of Contents