Display Setting - Yamaha BD-S667 Owner's Manual

SETUP MENU
Information
You can display network information screen. On this
screen, you can view the information of Interface
(Ethernet), Address Type, IP Address, Subnet Mask,
Default Gateway, and DNS.
Connection Test
You can perform a test for both cable connection and IP
settings, and it will ping default gateway. If the test is
failed, please check "IP Setting" (p. 30) and perform the
test again.
IP Setting
You can set IP Setting to Auto/Manual. When set to Auto,
IP address is allocated automatically by system. When set
to Manual, IP Address, Subnet Mask, Default Gateway
and DNS should be set manually.
*
Auto , Manual
BD-Live Connection
You can set access restriction to BD-Live contents.
Permitted * Allows all BD-Live discs to connect the network.
Partial
Allows only discs with owner certification.
Permitted
Prohibited Prohibits all BD-Live discs to connect the network.
DLNA
You can set the DLNA (p. 19) to Enable/Disable. When
you do not use the DLNA function, set to Disable.
*
Enable , Disable
Proxy Setting
You can set Proxy Setting. Set to Disable for normal use.
* Sets proxy server to disable. Select this item when
Disable
proxy server is not used.
Proxy Host Sets the proxy host.
Proxy Port Sets the proxy port.

■ Display Setting

The default settings are marked with "
TV
TV Screen
You can set the screen aspect ratio of the connected TV,
and adjust the video output.
If you switch your TV (i.e. because you have bought a
new one) and the screen aspect ratio of the connected TV
changes, you will have to change the TV Screen setting.
16:9 Full Select this when this Player is connected to a TV
with a 16:9 screen. When a 4:3 aspect ratio video is
played back, the video is displayed as shown below.
* Select this when this Player is connected to a TV
16:9 Normal
with a 16:9 screen. When a 4:3 aspect ratio video is
played back, the video is displayed as shown below.
4:3 Pan Scan Select this when this Player is connected to a TV
with a 4:3 screen. When a 16:9 aspect ratio video is
played back, the video is displayed as shown below.
4:3 Letterbox Select this when this Player is connected to a TV
with a 4:3 screen. When a 16:9 aspect ratio video is
played back, the video is displayed as shown below.
30
En
Original
image size
Original
image size
Resolution
You can select the video output resolution from Auto,
480i/576i, 480p/576p, 720p, 1080i, and 1080p. When set
to Auto, resolution is set to the maximum resolution
according to the connected TV. For more details on output
formats, refer to "About the video output formats" (p. 32).
*
Auto
TV System
You can select TV System from PAL, NTSC and Multi.
Set the same TV System as your TV set. For more details
on output formats, refer to "About the video output
formats" (p. 32).
NTSC
Note
– When no picture is displayed after this setting is
Color Space
You can select the Color Space (p. 37) output from
HDMI. This function is available when this Player is
connected with an HDMI cable.
".
*
RGB
YCbCr
YCbCr422
Note
– This function is only available on TVs that support
HDMI Deep Color
When your TV and/or AV receiver is compatible with
Deep Color (p. 37), set this item according to your TV/AV
receiver. This function is available when this Player is
connected with an HDMI cable.
30 bits, 36 bits, Off
On 16:9 (wide screen) TV
16:9 Full
4:3
On 4:3 TV
4:3 Pan Scan
16:9
, 480i/576i, 480p/576p, 720p, 1080i, 1080p
*
, PAL, Multi
changed, press and hold on the front panel for
around 5 seconds to switch NTSC/PAL manually.
Outputs video signal at normal signal range.
* Sets Color Space to YCbCr.
Sets Color Space to YCbCr422.
this function.
*
16:9 Normal
4:3 Letterbox