Specifications; Standard Accessories - Hitachi P 20SA2 Handling Instructions Manual

5) Service
a) Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children
and infi rm persons.

SPECIFICATIONS

Voltage (by areas)*
Power input
Cutting Width
Max. Cutting Depth
Weight (without cord and guide)
No-Load Speed
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

1. Box Wrench (for securing cutter blade) .......................1
2. Set Gauge (for adjusting cutter height) ........................1
3. Guide (with set screw) ..................................................1
4. Depth Guide .................................................................1
5. Blade Sharpening Ass'y
(for Resharpenable Blade Type) ..................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Dust collection adapter (Code no. 317279)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Planing various wooden planks and panels.
(See Fig. 1-4)
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
PLANER SAFETY RULES
1. Wait for the cutter to stop before settling the tool
down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
2. Do not use the Planer with the blades facing upward (as
stationary type planer).
3. Use dust collection adapter if need to reduce dust
related hazards.
(1) Unscrew the Chip guide (Item no. 17 show in
assembly drawing) on housing.
(2) Mount dust collection adapter on housing with
screws instead of the Chip guide.
Dust collection adapter (Code no. 317279)
(3) Connect the dust extraction and collection facilities
with the tube of dust collection adapter fi rmly.
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
720 W*
82 mm
3 mm
3.0 kg
14000 min
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prepare a stable wooden workbench suitable for
planing operation. As a poorly balanced workbench
creates a hazard, ensure it is securely positioned on
fi rm, level ground.
PLANING PROCEDURES
1. Adjusting the cutter depth:
(1) Turn the knob in the direction indicated by the arrow in
Fig. 5 (clockwise), until the triangular mark is aligned
with the desired cutting depth on the scale. The scale
unit is graduated in millimeters.
(2) The cutting depth can be adjusted within a range of 0-3
mm.
2. Surface cutting:
Rough cutting should be accomplished at large cutting
depths and at a suitable speed so that shavings
are smoothly ejected from the machine. To ensure
a smoothly fi nished surface, fi nish cutting should
be accomplished at small cutting depths and at low
feeding speed.
3. Beginning and ending the cutting operation:
As shown in Fig. 6, place the front base of the planer on
the material and support the planer horizontally. Turn
ON the power switch, and slowly operate the planer
toward the leading edge of the material. Firmly depress
the front half of the planer at the fi rst stage of cutting, as
shown in Fig. 7, depress the rear half of the planer at the
end of the cutting operation. The planer must always be
kept fl at throughout the entire cutting operation.
English
-1
7