Service Screen; Information Screen - Kenwood DDX7032 Service Manual

DDX7032/7032M/712
DNX7120/7220/7320
Key Specifi cation
Information : Transfer to Information screen.
Service : Transfer to Service screen.
Direct Select : Transfer to Direct Select screen.
Ext SW : Output Ext-SW waveform ("400ms ON/
OFF" by the operations, SW1 → SW2).
Touch : Transfer to Touch Adjust screen.
HPOSI : Transfer to HPOSI Adjustment screen.
iPod : Transfer to iPod Authentication Chip Confi r-
mation screen.
Tilt Mecha : Transfer to Tilt Mecha Position Adjustment
screen.
Auto Adjust : Transfer to Auto Adjust screen.
Inverter : Transfer to Inverter Confi rmation screen.
Bluetooth : Transfer to Bluetooth Confirmation screen
(only in Mid model). This key turns red after
the completion of Flash memory initializa-
tion in Bluetooth Module.
Parrot : Transfer to Parrot Confi rmation screen (only
in Mid model).

4.2. Information screen

This screen is to display such information as version num-
ber and other conditions.
The contents displayed on the Information screen are
shown in Figure 4.2.
Information
Serial No. : ∗∗∗∗∗∗∗∗
Media Processor : Redboot 12:00:00 Sep 15 2007
Low DDX System μ-com : V∗.∗∗∗
Low DDX Audio μ-com : V∗.∗∗∗
Mstar : V∗.∗∗∗
B/E : V∗.∗∗∗ F/E : V∗.∗∗∗
BT Module : V∗.∗∗∗
Figure 4.2 Information screen
• The "Low/Mid" and "DDX/DNX" that are attached in front
of System μ-com/Audio μ-com indicates that the desti-
nation information of the board on which System μ-com/
Audio μ-com are installed.
• Version information of BT Module is limited to Mid model.
Key Specifi cation
Return : Transfer to Test Mode Main screen
26
DC Offset : None Security : Off
Kernel Sep 15 12:00:00 JST 2007
RootFS 070915_12:00
ROM : R– – – – Type : ∗
ROM : R– – – – Type : ∗ Span : ∗
macrovision : V∗.∗∗∗ Region : ∗
Return
TEST MODE

4.3. Service screen

This screen shows a variety of service information. Press-
ing each [Clear] key clears the data saved in the nonvolatile
memory.
The contents displayed on the Service screen are shown in
Figure 4.3.
Service
Init
Init
■Start
DVD Service Info
∗∗∗∗
DVD DivX
Registration Code Clear
Key Specifi cation
Serial
DVD Service Info : Select the DVD video and display the
Tuner Mute Level : Transfer to Tuner Mute Level Adjust-
DVD DivX Registration Code Clear
DC Offset Clear
Init
■Start
Return
• DVD Service Info
Select the DVD video and display the DVD service infor-
mation that is created by DVD mechanism.
Use the [DISP] key or CURSOR (right or left) on the re-
mote controller to feed pages.
Press the [FNC] key to return from the DVD video to the
Service screen.
∗ Refer to the DVS-8500 system service documents for
the details of DVD Service Info screen.
Once the system transfers to DVD video screen selected
at DVD Service Info, OSD will not be displayed in the
DVD video screen. Restart the set (system) to display
OSD in DVD video screen.
Power ON ∗∗∗ minutes
Monitor Open ∗∗∗ times
DC Offset Clear
Tuner Mute Level
Figure 4.3 Service screen
: Transfer to the Serial No. Entry screen.
DVD service information.
ment screen
: Clear DVD DivX Registration Code.
: Clear DC Offset information in the non-
volatile memory.
: Select the item to be initialized.
: Pressing this key for one second or
longer initializes the information of the
item selected by [Init] key.
: Transfer to Test Mode Main screen
Serial
None
Return