Page 1 Product Version: 1.0 Second Edition (November 2002) Part Number: 269782-003 The HP StorageWorks Network Storage Router M2402 provides bi-directional connectivity in either a Fibre Channel Switched Fabric or a Fibre Channel Arbitrated Loop environment, supporting Fibre Channel and SCSI devices.
Page 2 “as is” without warranty of any kind and is subject to change without notice. The warranties for Hewlett-Packard Company products are set forth in the express limited warranty statements accompanying such products. Nothing herein should be construed as constituting an additional warranty. Network Storage Router M2402 User Guide Second Edition (November 2002) Part Number: 269782-003...
Page 3: Table Of Contents
HP Authorized Reseller ........
Page 4 Visual Manager Best Practices ..........46 Network Storage Router M2402 User Guide...
Page 5 Reboot Option............104 Network Storage Router M2402 User Guide...
Page 6 Displaying the Entire Device List ......... 149 Network Storage Router M2402 User Guide...
Page 7 Hardware Module Replacement Removing and Installing a Power Module or Power Bay Cover ..... 184 Network Storage Router M2402 User Guide...
Page 8 Mode Sense (6) and Mode Sense (10) Commands ......214 viii Network Storage Router M2402 User Guide...
Page 9 Laser Information............248 Network Storage Router M2402 User Guide...
Page 10 Grounding Methods ............250 Index Network Storage Router M2402 User Guide...
Page 11 About this Guide This user guide provides information to help you: Install the Network Storage Router M2402 About this Guide Configure the Network Storage Router M2402 About this Guide topics include: Overview, page xii Conventions, page xiii...
Page 12: About This Guide
This guide is intended for administrators with a moderate knowledge level about network environments. Prerequisites Before you install this product, make sure you consider the items below. Knowledge of operation system Knowledge of related hardware/software Previous version of the product/firmware Network Storage Router M2402 User Guide...
Page 13: Conventions
The following symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life. Network Storage Router M2402 User Guide xiii...
Page 14: Equipment Symbols
Contact with this surface could result in injury. To reduce the risk of injury from a hot component, allow WARNING: the surface to cool before touching. Network Storage Router M2402 User Guide...
Page 15: Rack Stability
In single rack installations, the stabilizing feet are attached to the rack. In multiple rack installations, the racks are coupled. Only one rack component is extended at any time. A rack may become unstable if more than one rack component is extended for any reason. Network Storage Router M2402 User Guide...
Page 16: Getting Help
Operating system type and revision level Detailed, specific questions HP Storage Website The HP website has the latest information on this product, as well as the latest drivers. Access storage at: http://www.hp.com. From this website, select the appropriate product or solution.
Page 17: Hp Authorized Reseller
HP Authorized Reseller For the name of your nearest HP authorized reseller: In the United States, call 1-800-345-1518 In Canada, call 1-800-263-5868 Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com. Network Storage Router M2402 User Guide xvii...
Page 18 About this Guide xviii Network Storage Router M2402 User Guide...
Page 19: Introduction
Introduction The HP StorageWorks Network Storage Router M2402 provides bi-directional connectivity for up to twelve Narrow/Wide Fast/Ultra-2 SCSI buses in either a Fibre Channel Switched Fabric (FC-SW) or a Fibre Channel Arbitrated Loop (FC-AL) environment. This chapter introduces the following topics: External features overview —...
Page 20: External Features Overview
The power supply modules (with fault and power LED) are serviceable from the front-side of the router. The serial port is also located on the front-side for local management of configuration settings and firmware upgrades. Figure 2: Back-side view Network Storage Router M2402 User Guide...
Page 21: Power Modules
The router is equipped with one power supply and has the capability of a redundant power supply being added. Figure 3: Power module Power supply LED definition: Green - Power has been applied to this module Yellow - Power-On Self-Test (POST) in process or processor problems Network Storage Router M2402 User Guide...
Page 22: Fan Modules
Web-based user interface. Note: The Web-based user interface is also called Visual Manager. Visual Manager is discussed in Chapter 4, “Visual Manager User Interface.” The Serial/Telnet user interface is discussed in Chapter 5, “Serial/Telnet User Interface.” Network Storage Router M2402 User Guide...
Page 23: Fibre Channel Modules
Multiple Fibre Channel modules can be added to the router. Figure 5: Fibre Channel module Fibre Channel module LED definition: Green (ACT) - Fibre Channel port activity Green (LINK) - Valid Fibre Channel link Network Storage Router M2402 User Guide...
Page 24: Scsi Modules
This button does not remove power to the power module(s). To remove power to the power module(s), unplug the router from electrical source. Note: The standby power button has a 10-second delay after disengaging power before power can be re-engaged. Network Storage Router M2402 User Guide...
Page 25 Activity - Port activity Link - Valid Ethernet link Standby power button LED definition: Green - System power is on Amber - System fault condition is indicated Alternating Green/Amber - System in Beaconing mode Network Storage Router M2402 User Guide...
Page 26: Serial Port
The router is equipped with one serial port. See Figure 8 for an illustration. The serial port can be used to access the serial/Telnet user interface, which is used to locally manage and configure the router. Figure 8: Serial port Network Storage Router M2402 User Guide...
Page 27: Functional Overview
Figure 9: Example configuration Figure 9 shows that a Fibre Channel host on the Fibre Channel bus can access a tape drive and library through the appropriate SCSI bus of the router I/O module. Network Storage Router M2402 User Guide...
Page 28: Fibre Channel To Scsi Protocol Process
The router interprets the Fibre Channel information packet and programs the router SCSI controller to process the transaction. The router SCSI controller sends the command to the SCSI device (target). The SCSI target interprets the command and executes it. Network Storage Router M2402 User Guide...
Page 29: Scsi To Fibre Channel Protocol Process
Fibre Channel controller to process the transaction. The router Fibre Channel controller translates data into an FCP protocol packet and sends it to the Fibre Channel target. The Fibre Channel target interprets the FCP protocol packet and executes the command. Network Storage Router M2402 User Guide...
Page 30: Lan-Free Backup And Restore
Fibre Channel ETHERNET SCSI TAPE UNIT SCSI DATA MOVEMENT SCSI TAPE UNIT StorageWorks Router FIBRE CHANNEL DISK StorageWorks Router SERVER SERVER SERVER SERVER Figure 12: LAN-free backup and restore Network Storage Router M2402 User Guide...
Page 31: Server-Free Data Movement
DISK StorageWorks Router SERVER SERVER SERVER SERVER Figure 13: Server-free data movement Note: The router implementation of Extended copy does not support the SNMP protocol. Note: Copy Manager can perform simultaneous Extended Copy commands. Network Storage Router M2402 User Guide...
Page 32: Physical Requirements
If the router is to be shipped or stored, the following environment must be maintained: Temperature: -40 to +55°C Relative Humidity: 0 to 92% (non-condensing) The router must be supplied the following power: VAC: 100 - 240 (auto sensing) 50/60 Hz, 2.0 Amps (each power supply) Network Storage Router M2402 User Guide...
Page 33: Installation
Installation This chapter describes how to unpack and install the StorageWorks Network Storage Router M2402. The router can be set up in either a desktop or a rack configuration. Note: Read this chapter carefully and completely before configuring the router.
Page 34: Selecting A Location
Installing the Router in a Rack The following items in the router kit are used to rack-mount the router: Mounting rails Extender brackets Bag of mounting hardware (8 #M6x12 Phillips screws, 4 #6-32x.312 Phillips screws) Bezel blank Network Storage Router M2402 User Guide...
Page 35 Extend the inner rail out from the outer-rail assembly until it locks into place. c. Press the spring-latch on the back-side of the inner rail to release the lock. While holding down the spring-latch, extend the inner rail until the two rails separate. Network Storage Router M2402 User Guide...
Page 36 All three holes must be aligned exactly. If the holes do not exactly match up, the outer-rail assembly is not positioned correctly on the rack. See Figure 15 for an example of rack front styles and hole alignments. Network Storage Router M2402 User Guide...
Page 37 With the outer-rail assembly in place, tighten the flathead screw that connects the rear extension bracket to the outer rail. h. Repeat Step 4 to attach the other outer-rail assembly to the other side of the rack. Network Storage Router M2402 User Guide...
Page 38 When the rails lock in place, press in the spring-latches on each of the inner-rails and push in the rest of the way. Network Storage Router M2402 User Guide...
Page 39 Align the bezel blank over the unused center hole of the bracket faces on the rack. b. Attach the bezel blank to the rack, using the thumbscrews. Figure 18: Attaching the bezel to the rack Network Storage Router M2402 User Guide...
Page 40: Connecting The Power Cord
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Disconnect power from the router by unplugging the power cord from either the electrical outlet or the router. Network Storage Router M2402 User Guide...
Page 41: Connecting The Interfaces
SCSI Connections (HVD or LVD/SE) Ethernet Connections Serial Port Connections (RS-232) Figure 20 is an illustration of the port locations on the router. Figure 20: Back-side and front-side port locations Item Port Type Fibre Channel SCSI Ethernet Serial Network Storage Router M2402 User Guide...
Page 42: Fibre Channel Connections
Failure to correctly configure a Fibre Channel device may impair the operation of the storage network to which it is attached. Network Storage Router M2402 User Guide...
Page 43 Fibre Channel cabling for the media type in use. The router supports various Fibre Channel media types, using external Small Form Factor Pluggables (SFP). Available media types use 2.125-Gb Dual SC connectors and include: Multi-mode fiber support Single-mode fiber support Network Storage Router M2402 User Guide...
Page 44 Caution: The router has been qualified with a specific set of SFPs. Using an SFP that has not been qualified by HP may cause the router to operate improperly. See the Laser Safety section of this manual for more information.
Page 45: Scsi Connections
SCSI cables used with the router must meet SCSI 2 standards. Optional SCSI cables are available from your supplier. To connect the router to a SCSI device: 1. Power off the router and SCSI devices. 2. Locate the SCSI buses on the back-side of the router. Network Storage Router M2402 User Guide...
Page 46 However, the device at the other end of bus must also be terminated. 6. Power on all attached SCSI devices. 7. After all the SCSI devices have completed their individual POST (Power-On Self-Test) processes, power on the router. Network Storage Router M2402 User Guide...
Page 47: Ethernet Connections
The router has a unique Ethernet MAC address that is assigned during the manufacturing process. Ethernet interfaces include Telnet, SNMP, FTP, and an HTTP interface known as StorageWorks Visual Manager (VM). For more information on router management, see Chapter 3, “Configuration Overview.” Figure 25: Ethernet port Network Storage Router M2402 User Guide...
Page 48: Serial Port Connections
Figure 26: Serial port Item Settings Baud Rate Autobaud, 9600, 19200, 38400, 57600, or 115200 HP recommends setting the baud rate to 115200. Data Bits Stop Bits Parity None Flow Control...
Page 49: Setting Up Serial Port Communications
This process can take up to 90 seconds. The Power On Self Test (POST) and initialization information may not be visible on screen. Note: The baud rate in the terminal emulation program must be set at 9600, 19200, 38400, 57600, or 115200 to use the autobaud feature. Network Storage Router M2402 User Guide...
Page 50 Installation Network Storage Router M2402 User Guide...
Page 51: Configuration Overview
Configuration Overview The StorageWorks Network Storage Router M2402 can be configured and managed using several user interfaces (UIs). Each UI is introduced in this chapter, along with information about common configuration settings. Router default settings UI overview Common configuration settings —...
Page 52: Router Default Settings
HP recommends these values be changed from the defaults. All settings within the router configuration are pre-set with default values. These values are set to allow the router to be installed into most HP environments with little or no configuration changes.
Page 53: Ui Overview
5, “Serial/Telnet User Interface.” The router supports the use of the FTP UI to perform several copy procedures using the “ ” and the “ ” commands. For more information, see Chapter 6, “FTP User Interface.” Network Storage Router M2402 User Guide...
Page 54: Snmp Management Information Base
Fibre Channel bus. These commands provide support for value added features such as Extended Copy. When using these commands, they must be sent to the Controller LUN. For more information, see Appendix “Controller LUN Commands.” Network Storage Router M2402 User Guide...
Page 55: Scsi Bus Configuration
Channel port speed must be manually set, such as for 2 Gb/s. If set incorrectly and the router is plugged into a Loop or Fabric, the unit may receive framing errors because of the incorrect Fibre Channel link speed. Network Storage Router M2402 User Guide...
Page 56: Fibre Channel Arbitrated Loop Configuration
Fibre Channel Switched Fabric Configuration When connected to a Fibre Channel switch, the router is identified to the switch as a unique device by the factory programmed World Wide Name (WWN). Network Storage Router M2402 User Guide...
Page 57: Discovery Mode
1, then the address is 1. If the selection is 125, the AL_PA address is 0xEF. Some Fibre Channel HBAs will map devices differently, so verify the AL_PA by reviewing the documentation for the HBA. Network Storage Router M2402 User Guide...
Page 58: Logical Unit Management
ID is the Initiator ID (0 - 15). When a host is unknown or is not assigned a specific map, the router will use the default map. Indexed Maps An Indexed map is initially empty and can be modified by the user. Network Storage Router M2402 User Guide...
Page 59: Auto Assigned Maps
Some applications require confirmation of individual blocks being written to the medium, such as for audit trail tapes or log tapes. In these instances, the Buffered Tape Writes option must be disabled. Network Storage Router M2402 User Guide...
Page 60 Configuration Overview Network Storage Router M2402 User Guide...
Page 61: Visual Manager User Interface
Visual Manager best practices Main Menu System Menu — Serial configuration — Network configuration — SNMP configuration — Active Fabric configuration — User Configuration — Real-Time clock configuration — Power Supply configuration — Reset Menu Network Storage Router M2402 User Guide...
Page 62 — FTP utility access — Trace settings configuration — Current, previous, and last assert trace displays — Clear current traces and clear assert traces — Event log configuration — Event log display Report Menu Reboot Option Network Storage Router M2402 User Guide...
Page 63: Visual Manager Access
. This root password information is required only once per session. Note: HP recommends changing the user name and password from the defaults. Note: User name and password are case-sensitive. Network Storage Router M2402 User Guide...
Page 64: Visual Manager Best Practices
Fields are not case-sensitive, except for the user name and password. HP recommends that you not bookmark VM pages with the Web browser. Because configuration information is transmitted via URLs, it is possible that the router could be configured with information present at the time a page was bookmarked.
Page 65: Main Menu
The Main Menu home page is displayed whenever VM is accessed. The home page contains status information, including a physical image of the back-side of the router. Figure 27 is an example of the home page. Figure 27: Visual Manager home page Network Storage Router M2402 User Guide...
Page 66 Visual Manager User Interface Home page information includes: The HP logo is located in the upper left corner of the page. Figure 28 is an example of this portion of the home page screen. If the Internet is accessible to the host, click the HP logo to open the router company website.
Page 67 The Main Menu option bar is located at the left-side of the home page. Use this option bar to access the configuration menus. Figure 30 is an example of this portion of the home page screen. Figure 30: Main Menu option bar Network Storage Router M2402 User Guide...
Page 68 — Statistics shows router statistics. — Utilities configures utility settings. — Report shows and prints system information. — Reboot restarts the router. Each Main Menu option is discussed in the following sections of this chapter. Network Storage Router M2402 User Guide...
Page 69: System Menu
The System Menu is accessed from the Main Menu and is used to view and configure serial, network, SNMP, Trap, Active Fabric, clock, and power supply components. Figure 31 is an example of the System page. Figure 31: System page Network Storage Router M2402 User Guide...
Page 70 User configuration configures user security settings. Real-Time Clock configuration configures system date and time. Power Supply configuration configures the number of power supplies. Reset menu restores factory default settings. Each menu option is discussed in the following paragraphs. Network Storage Router M2402 User Guide...
Page 71: Serial Configuration
If the Autobaud feature is being used, it may not be necessary to set the baud rate. Figure 32: Serial screen The current baud-rate setting is displayed. HP recommends setting this value to 115200. Network Storage Router M2402 User Guide...
Page 72: Network Configuration
Network screen. Figure 33: Network screen The Network screen is divided into two sections: Ethernet Configuration Settings sets the hostname and Ethernet configuration settings Ethernet Override Settings changes Ethernet override settings. Network Storage Router M2402 User Guide...
Page 73: Ethernet Configuration Settings
IP address to the router. This setup can be useful for remote management of the router via Telnet or VM. Because the method of setting up a lease reservation varies, depending on the DHCP server being used contact the Network Administrator for assistance. Network Storage Router M2402 User Guide...
Page 74: Ethernet Override Settings
If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 75: Snmp Configuration
The community name in the SNMP packet must match this community name for the SNMP GET request to be successfully completed. Configure the SNMP manager to have the same GET and SET community names as the router. Network Storage Router M2402 User Guide...
Page 76 — Disabled (0) clears to the default settings — No Traps (1) no traps exist — Row Exist (2) row exists but traps are not sent to target — Send Traps (3) row exists and traps are sent Network Storage Router M2402 User Guide...
Page 77: Active Fabric Configuration
Visual Manager User Interface Active Fabric Configuration The Active Fabric screen allows setup of Active Fabric options. Figure 36 is an example of the Active Fabric screen. Figure 36: Active Fabric screen Network Storage Router M2402 User Guide...
Page 78 Fibre Channel Targets. For information on controller LUN and Extended Copy commands, see Appendix B, “Controller LUN Commands.” For general information about server-free backups, see Chapter 1, “Introduction.” Network Storage Router M2402 User Guide...
Page 79: User Configuration
The User screen is used to set up router security. Figure 37 is an example of the User screen. Figure 37: User screen User settings: User Name (default: ) is any alphanumeric combination. root Password (default: ) is any alphanumeric combination. password Network Storage Router M2402 User Guide...
Page 80: Real-Time Clock Configuration
Visual Manager User Interface The user name and password should be unique and kept confidential. HP recommends using a combination of letters and numbers when creating the user name and password. Note: These security settings affect all user interfaces of the router.
Page 81: Power Supply Configuration
Note: If there are two power supplies, and one of the two fails, this option does not inhibit the router from using the second power supply. Network Storage Router M2402 User Guide...
Page 82 Visual Manager User Interface Figure 39: Power supply screen Network Storage Router M2402 User Guide...
Page 83: Reset Menu
Current router activities will be disrupted while the unit resets the configuration to the factory defaults and saves those options to FLASH memory. Note: Resetting to factory defaults through VM will not affect Ethernet connectivity. User-configured values for the IP address and gateway will be retained. Network Storage Router M2402 User Guide...
Page 84: Modules Menu
The initial screen display of the Modules Menu includes summary information about each Fibre Channel and SCSI module in the router. Figure 41 for an example of the initial Modules Menu. Figure 41: Modules menu Network Storage Router M2402 User Guide...
Page 85: World Wide Node Name Configuration
These WWN settings are not normally changed. Caution: Changing the WWN Name could result in duplicate names on a single Storage Area Network (SAN). HP recommends using the default values for World Wide Names. Note: For Controller LUN commands to be operational, WWN naming schemes MUST be compliant with IEEE Fibre Channel Format 1, where the left-most hexadecimal character (the NAA field) of the WWN is '1'.
Page 86: Fibre Channel Module Configuration
Fibre Channel module on the router image. Figure 43: Fibre Channel module image The following screen is displayed to enter configuration changes. Figure 44 is an example of the FC Module Port Configuration Settings screen. Network Storage Router M2402 User Guide...
Page 87 — N_Port (default) This mode allows the router to bypass the loop negotiation and come up as a fabric only. If the router is on a loop, and N_Port mode is selected, an error in communication may occur. Network Storage Router M2402 User Guide...
Page 88 (derived from an Arbitrated Loop Topology defined in ANSI specification FC_AL version 4.5) is used for the Fibre Channel configuration. Figure 45 is an illustration of the AL_PA table. Figure 45: AL_PA lookup table Network Storage Router M2402 User Guide...
Page 89 If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 90 If these configuration settings are incorrectly set, processing difficulties may occur. Before changing these settings, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 91 If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 92: Scsi Module Configuration
SCSI module on the router image. Figure 47: SCSI module image After a bus on the SCSI module is selected, the SCSI Module Bus Configuration Settings screen is displayed for that bus. See Figure Network Storage Router M2402 User Guide...
Page 93 If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 94 Discovery Delay is the wait time after a power-up or reboot before discovering SCSI devices. Note: HP recommends setting the value to at least 2 seconds to ensure all SCSI devices complete their individual power-ups. Bus Reset on Boot toggles between Enabled and Disabled.
Page 95 Caution: may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting. The current map can be set to: —...
Page 96 Ultra SCSI-3 but cannot handle the speed. Network Storage Router M2402 User Guide...
Page 97: Discovery Menu
Discovery page. Figure 50: Discovery page In the Discovery Menu, select a specific Fibre Channel Port or SCSI bus from the Menu Bar or the router image and then click Go. Network Storage Router M2402 User Guide...
Page 98: Mapping Menu
The initial screen display lists all available hosts and the assigned map for the selected Fibre Channel port or SCSI bus. Figure 51 is an example of the initial Mapping screen. Figure 51: Mapping screen Network Storage Router M2402 User Guide...
Page 99: Fibre Channel And Scsi Common Mapping Tasks
To select a previously set up map, expand the Select Map drop-down box and select the map from this list. Delete Host deletes the current host. Note: ‘Built at runtime’ hosts cannot be deleted. Network Storage Router M2402 User Guide...
Page 100: Fibre Channel Mapping Tasks
2. Click Edit/View in the Host section of the screen. The Fibre Channel Host Name dialog box is displayed. Current host information is shown at the top of the dialog box. 3. Enter the new settings and then click Modify. Network Storage Router M2402 User Guide...
Page 101 Figure 52: Fibre Channel Host Name dialog box Fibre Channel Host Name settings: Host Name Host ID (hexadecimal) Port WWN Hi (hexadecimal) Port WWN Lo (hexadecimal) Node WWN Hi (hexadecimal) Node WWN Lo (hexadecimal) Map Name Network Storage Router M2402 User Guide...
Page 102: Viewing And Changing Fibre Channel Map Information
3. Enter the new settings and then click the appropriate action button. Figure 53 is an example of the Fibre Channel Map dialog box. Figure 53: Fibre Channel Map dialog box Network Storage Router M2402 User Guide...
Page 103 To add a discovered device to the map, use the drop-down boxes to enter the settings, and then click Create Entry in the Discovered Device Entry section of the screen. Manual Device Entry create a map entry for a device that is not yet discovered or installed. Network Storage Router M2402 User Guide...
Page 104: Scsi Mapping Tasks
The SCSI Host Name dialog box is displayed. Current host information is shown at the top of the dialog box. 3. Enter the new settings and then click Modify. Figure 54 is an example of the SCSI Host Name configuration dialog box. Network Storage Router M2402 User Guide...
Page 105: Viewing And Changing Scsi Map Information
The SCSI Map dialog box is displayed. Current map information is shown at the top of the dialog box. 3. Enter the new settings and then click the appropriate action button. Figure 55 is an example of the SCSI Map dialog box. Network Storage Router M2402 User Guide...
Page 106 Target ID can be used to store up to 32 Fibre Channel devices. Note: Auto-Assigned and SCC maps cannot be modified, cleared, filled, or have entries deleted. Note: Map settings are saved to memory when any button within the page is selected. Network Storage Router M2402 User Guide...
Page 107 Create Entry in the Manual Device Entry section of the screen. Note: SCSI maps can be filled or devices can be added to them only when at least one SCSI Target ID has been enabled in the SCSI bus configuration menu. Network Storage Router M2402 User Guide...
Page 108: Statistics Menu
Statistics Menu. Figure 56: Statistics Menu To view information for a specific module port/bus, click the component on menu bar or the router image. To reset the statistics, click Go. Network Storage Router M2402 User Guide...
Page 109: Utilities Menu
Visual Manager User Interface Utilities Menu Accessed from the Main Menu, the Utilities Menu is used to view and configure utility options. Figure 57 is an example of the Utilities Menu. Figure 57: Utilities menu Network Storage Router M2402 User Guide...
Page 110: Beacon Mode Configuration
When enabled, the Power LED located on the back-side of the router will continuously blink, alternating between amber and green. To enable the Beacon settings, select the ON checkbox and then click Submit. Figure 58 is an example of the Beacon settings screen. Network Storage Router M2402 User Guide...
Page 111 Visual Manager User Interface Figure 58: Beacon configuration screen Note: When the router is rebooted, beaconing is automatically disabled. Network Storage Router M2402 User Guide...
Page 112: Ftp Utility Access
The FTP Utility requires the use of a JAVA applet and prompts for permission to install the applet, if needed. If the prompt is displayed, follow the onscreen instructions to complete the installation. The FTP Utility then prompts for permission to run the applet. Network Storage Router M2402 User Guide...
Page 113 Visual Manager User Interface Note: Internet access is required to verify the signature for the HP FTP applet and to download the JAVA applet plug-in for your browser. To open an FTP session: 1. Enter the User Name, Password, and the IP address of the router.
Page 114: Trace Settings Configuration
Current Trace settings are displayed. To change the settings, use the drop-down boxes and select the desired setting. After all changes are completed, click Submit. Table 2 is a brief description list of the trace settings. Network Storage Router M2402 User Guide...
Page 115 Parallel SCSI functionality will be monitored and recorded. SG List Scatter/gather list will be monitored and recorded. FCP/RMI Fibre Channel Protocol routing layer will be monitored and recorded. INBAND Controller management functionality will be monitored and recorded. Network Storage Router M2402 User Guide...
Page 116: Current, Previous, And Last Assert Trace Displays
The Previous Traces screen shows data from the last boot cycle. The Last Assert Traces screen shows data since the last assertion. Figure 61 is an example of the Current Traces screen. Figure 61: Current Traces screen Network Storage Router M2402 User Guide...
Page 117: Clear Current Traces And Clear Assert Traces
These Utilities Menu screens are used to clear the current trace buffer or the assert trace buffer. Current router activities will not be disrupted while the buffer is cleared. Figure 62 is an example of the Clear Current Trace Buffer screen. Figure 62: Clear Current Trace Buffer screen Network Storage Router M2402 User Guide...
Page 118: Event Log Configuration
Figure 63: Event Log settings screen Event Log settings: Log All Events Disable/Enable Event Logging Log Error Events Log Notify Events Event logging captures the last 215 events and then starts overwriting the log. Network Storage Router M2402 User Guide...
Page 119: Event Log Display
Real Time Clock Configuration menu. Event Log Display The Event Log screen is used to view the Event Log. Figure 64 is an example of the Event Log display screen. Figure 64: Event Log display screen Network Storage Router M2402 User Guide...
Page 120: Clear Event Log
The Clear Event Log screen is used to clear the Event Log. Figure 65 is an example of the Clear Event Log screen. Current router activities will not be disrupted. Figure 65: Clear Event Log screen Network Storage Router M2402 User Guide...
Page 121: Report Menu
Accessed from the Main Menu, the Report page displays a consolidated view of all system information, including environmental conditions. Figure 66 is an example of the Report page. To print the system information, click Printable View. Figure 66: Report screen Network Storage Router M2402 User Guide...
Page 122: Reboot Option
Figure 67 is an example of the Reboot screen. When the router is rebooted, current router activities will be disrupted. All submitted configuration changes will be activated during the boot-up process. Figure 67: Reboot screen Network Storage Router M2402 User Guide...
Page 123: Serial/Telnet User Interface
Serial/Telnet User Interface The Serial/Telnet User Interface (UI) is used to configure and manage the StorageWorks Network Storage Router M2402. This chapter describes the configuration menus and option tasks available in the Serial/Telnet UI. Note: Unless otherwise indicated, configuration changes take effect when the router reboots.
Page 124 Reset and save configuration to factory defaults System utility menu — System statistics — Event log — Beacon settings Trace dump menu — Saving copies of the trace buffers using FTP Reboot option Download new firmware option Network Storage Router M2402 User Guide...
Page 125: Telnet Ui Access
3. Enter the user name and password. The default user name is and the default password is root password HP recommends that the user name and password be changed from the default values. 4. The Configuration Menu is displayed. Network Storage Router M2402 User Guide...
Page 126: Serial Ui Access
Options include COM1 and COM2. 4. Configure the serial port settings, as listed in the “Installation” chapter. Note: HP recommends setting the baud rate to 115200. 5. After completing the serial port configuration, select OK to start a serial session.
Page 127: Power Up Messages
When power is applied to the router, a series of messages is displayed on the serial terminal or terminal emulation program. Figure 68 is an example of these power-up messages. Figure 68: Power up messages Note: Throught this chapter, represents value fields. Network Storage Router M2402 User Guide...
Page 128: Serial/Telnet Ui Main Menu
Each main menu option is discussed in a separate section of this chapter. Note: Uppercase and lowercase characters can be used interchangeably in all of the menus. Network Storage Router M2402 User Guide...
Page 129: Configuration Menu
After any configuration changes are made, select A) Save Configuration to record the changes. If the configuration has been modified to meet company-specific needs, back up the company-specific configuration to an external file. If necessary, these settings can later be restored to the router. Network Storage Router M2402 User Guide...
Page 130 Return to main menu (X) goes back to the previous screen. Because the Configuration Menu is the primary menu in the UI, each Configuration Menu option is discussed in a separate section. Network Storage Router M2402 User Guide...
Page 131: Baud Rate Configuration
To change the baud rate enter the number (1 through 5) that represents the desired rate. Note: The asterisk (*) symbol indicates the current setting for the baud rate. Note: If the Autobaud feature is being used, it is not necessary to set a baud rate. Network Storage Router M2402 User Guide...
Page 132: Ethernet And Snmp Configuration
Figure 72: Ethernet Configuration menu Note: To view or change configuration settings, select the desired menu option. After completing configuration changes, select X) Return to previous menu and then select A) Save Configuration to record the changes. Network Storage Router M2402 User Guide...
Page 133 If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 134 Configure the SNMP manager to have the same SET community name as the router. — Toggle Trap (3) enables or disables Traps. If SNMP Traps are disabled, no Trap events are sent. Network Storage Router M2402 User Guide...
Page 135 Note: The security settings entered here affect all user interfaces. User names and passwords should be unique and kept confidential. HP recommends using a combination of letters and numbers when creating user names and passwords. Network Storage Router M2402 User Guide...
Page 136: World Wide Node Name Configuration
To change the World Wide Name, select the appropriate Change Fibre Channel World Wide Node Name option (1) or (2). Note: If the Configuration Settings are reset to the factory defaults, these customized settings will be overwritten. Network Storage Router M2402 User Guide...
Page 137: Modules Configuration
To configure the selected module, select Configure Module Settings (1). Different sets of sub-screens are displayed for Fibre Channel and SCSI modules. This section is further subdivided into the following sections: Configuring Fibre Channel Modules Configuring SCSI Modules Network Storage Router M2402 User Guide...
Page 138: Configuring Fibre Channel Modules
The Fibre Channel Configuration Menu allows the user to configure the Fibre Channel Address method, Hard Address value, discovery mode, WWN overrides, tape backup settings, default map value, and Fibre Channel port mode. Figure 75: Fibre Channel Configuration menu Network Storage Router M2402 User Guide...
Page 139 If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 140 LUN position is found. — Manual Discovery Only sets discovery of new devices to only occur after the user selects the Refresh Device Display option. The Refresh Device Display option is accessed from the System Utilities Menu. Network Storage Router M2402 User Guide...
Page 141 If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 142 If these configuration settings are incorrectly set, processing difficulties may occur. Before changing these settings, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 143: Configuring Scsi Modules
Serial/Telnet User Interface Configuring SCSI Modules When a SCSI module is selected in the Module Configuration Menu, the SCSI Configuration Menu is displayed: Figure 76: SCSI Configuration menu Network Storage Router M2402 User Guide...
Page 144 If these configuration settings are incorrectly set, processing difficulties may occur. Before changing these settings, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 145 This value should be set to no less than 250ms, according to the SCSI standard for Reset-to-Selection Time. HP recommends setting the value to at least 2 seconds to ensure all SCSI devices complete their individual power on self tests (POST.) Set SCSI Termination Mode (5) enables or disables the SCSI termination mode.
Page 146 — Editing the Current Map — Cloning a Map — Editing the Host List for the Current Map — Viewing the Entire Device List <Enter> scrolls to the next SCSI bus on this module. Network Storage Router M2402 User Guide...
Page 147: Device Mapping
SCSI mappings, select Change Map Settings (8). 3. Regardless of the selected module type, the same Device mapping Configuration menu will be displayed. Figure 77 is an example of the Device Mapping Configuration Menu for a Fibre Channel module. Network Storage Router M2402 User Guide...
Page 148: Changing To The Next Port Or Bus
Because each option includes a menu or sample screen display, each menu option is discussed in the following separate sections. Changing to the Next Port or Bus To scroll to the next Fibre Channel port or SCSI bus, press Enter. Network Storage Router M2402 User Guide...
Page 149: Selecting The Current Map
If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting.
Page 150: Viewing The Current Map
Fibre Channel maps and SCSI maps. Figure 79: FCP Current Map display Note: The entire list may not fit on one screen. Press N or P to go back and forth between screens. Network Storage Router M2402 User Guide...
Page 151: Creating A New Map
Current Map. Removing the Current Map In the Device Mapping Configuration menu, Remove Current Map (4) is used to remove the Current map and restore the default map as Current. A verification prompt is displayed. Network Storage Router M2402 User Guide...
Page 152: Editing The Current Map
Edit Map Entries (2) changes the content of the current map. Clear Map (3) erases all entries from the current map. Fill Map (4) automatically completes the entries for the current map. Each editing option is discussed in the following sections. Network Storage Router M2402 User Guide...
Page 153: Changing The Name Of The Current Map
Although the options are the same for editing maps of Fibre Channel and SCSI modules, the screen display differs. Figure 82 is an example screen display for Fibre Channel maps and Figure 83 an example screen display for a SCSI map. Network Storage Router M2402 User Guide...
Page 154 Next (N) scrolls down the list of map entries. Previous (P) scrolls up the list of map entries. Add (A) adds new map entries. Create (C) creates a new map entry for a newly added device. Network Storage Router M2402 User Guide...
Page 155: Scrolling Between Display Pages Of The Edit Map Entries Screen
To add a new entry to a Fibre Channel map: 1. In the Map Edit Entries screen, select Add (A). The following screen is displayed: Figure 84: Adding an Entry to a Fibre Channel map Network Storage Router M2402 User Guide...
Page 156 4. In the Device List, to add a listed device to the map, enter the number from the “Num” column. If the selected device is already mapped, an error message will appear, warning about adding a duplicate device. Network Storage Router M2402 User Guide...
Page 157: Adding A Map Entry To A Scsi Map
If the selected Target/LUN is already present in the map, a prompt is displayed that asks to either confirm the override or enter different address information. A device selection list is automatically generated. Note: Devices cannot be mapped to their native port. Network Storage Router M2402 User Guide...
Page 158: Creating A Map Entry For A Fibre Channel Map
All essential information about the device must be known. A series of questions is displayed. The questions will vary based on the ‘Current’ map protocol. Required information includes the LUN address, protocol, port, device name, and device type must be entered. Network Storage Router M2402 User Guide...
Page 159: Creating An Entry For A Scsi Map
Required information includes the Target ID and LUN address, protocol, port, device name, and device type must be entered. Figure 89 is an example of the screen display when creating an entry for a SCSI map. Network Storage Router M2402 User Guide...
Page 160: Removing Gaps In The Map
To remove any incremental gaps in the sequence of LUN listed in the table, in the Edit Map Entries screen, select Remove (R). As the system removes any gaps from the table, the LUN are renumbered in sequential order, starting with LUN 0. Network Storage Router M2402 User Guide...
Page 161: Deleting A Map Entry
Current map. Note: Auto Assigned maps and SCC maps cannot be cloned. The new map must have a unique name. After the cloning process is complete, this copy becomes the Current map. Network Storage Router M2402 User Guide...
Page 162: Editing The Host List For The Current Map
Although the options are the same for FCP maps and SCSI maps, the screen display differs. Figure 90 Figure 91 are examples of the Host List Display screens for FCP and SCSI maps. Figure 90: Host List Display for Fibre Channel maps Network Storage Router M2402 User Guide...
Page 163: Scrolling Between The Display Pages Of The Host List Edit Screen
To scroll up and down the host entries, select P or N. Selecting a Host To select a host from the list, enter the number displayed in the “N#” or the “Num” column at the left of the screen. Network Storage Router M2402 User Guide...
Page 164: Adding A Host To The Host List
Figure 93: Adding a Host to the Host List - SCSI host Deleting a Host from the Host List To remove a host from the Host List, select Delete (D). After entering the number of the host to delete, a confirmation prompt is displayed. Network Storage Router M2402 User Guide...
Page 165: Editing Host Information
Fibre Channel module. Figure 94: Editing Host information on a Fibre Channel module Figure 95 is an example of editing host information for a SCSI module. Network Storage Router M2402 User Guide...
Page 166 Serial/Telnet User Interface Figure 95: Editing Host Information for a SCSI module Network Storage Router M2402 User Guide...
Page 167: Displaying The Entire Device List
Note: The entire list of maps may not fit on one screen. Select ‘N’ or ‘P’ to go back and forth between screens displaying more maps. Select ‘X’ to return to the previous menu. Network Storage Router M2402 User Guide...
Page 168: Trace And Event Settings Configuration
The current setting is toggled to either On or Off. 2. Repeat Step 1 for each setting that needs to be changed in the page. 3. Before leaving the page, activate the new setting by entering Update Current Operating Trace levels (U). Network Storage Router M2402 User Guide...
Page 169 Note: Be sure to set the clock and date in the Real Time Clock Configuration menu so that event logging is accurate. Figure 98: Trace Settings screen Network Storage Router M2402 User Guide...
Page 170: Configuring Event Settings
Figure 99: Trace Settings screen, continued Configuring Event Settings In the Utility Trace Settings Menu, Event Settings Configuration (2) is used to modify event filters. The following Event Filter Settings screen is displayed: Figure 100: Event filter settings Network Storage Router M2402 User Guide...
Page 171 This option forces the currently displayed trace settings to become effective immediately, without requiring a reboot or power cycle. Note: Set the clock and date in the Real-Time Clock Configuration menu so that event logging is accurate. Network Storage Router M2402 User Guide...
Page 172: Real-Time Clock Configuration
Figure 101: Clock Setup menu 1. To change the date or time, select Set clock (1). 2. A series of prompts are displayed, allowing setup of: 24-hour time Current date Current day of the week Network Storage Router M2402 User Guide...
Page 173: Active Fabric Configuration
LUN. This setting is a number in the range of 0 through 4. Note: For Server-Free Backup Mode functionality, if addressing a Controller LUN is desired, at least one controller LUN must be enabled and included in a relevant map. Network Storage Router M2402 User Guide...
Page 174: Power Supply Configuration
Note: For systems with two working power supplies, HP recommends setting this option to Dual Mode to allow the router to issue an event notification should one of the power supplies fail. However, if set to Single Mode and one of the power supplies does fail, the router will still use the second power supply but just will not issue an event notification.
Page 175: Save Configuration
Reset and Save Configuration to Factory Defaults In the Configuration Menu, Reset and Save Configuration to Factory Defaults (C) is used to reset the router configuration to its initial settings. Network Storage Router M2402 User Guide...
Page 176: System Utility Menu
Special Fibre Channel Link States (4) (This option is a special diagnostic utility used only by authorized service technicians.) Beacon Settings (5) enables or disables the Beacon LED signal. Each System Utility Menu option is discussed in a separate section. Network Storage Router M2402 User Guide...
Page 177: System Statistics
In the System Statistics Menu, select Display System Status (1) to view a variety of status information, including memory statistics, current active tasks, and stack usage. The System Status Menu is displayed. Figure 106 is an illustration of the System Status Menu. Network Storage Router M2402 User Guide...
Page 178 1) Display memory statistics shows memory usage information. 2) Display active tasks shows a list of current tasks. 3) Display stack usage shows current stack information. 4) Display SCSI Protocol Resources shows SCSI protocol information. Network Storage Router M2402 User Guide...
Page 179: Viewing Environmental Status Information
The Environmental Statistics page is displayed. The Environmental Statistics page has no options. It is used to view environmental conditions measurements. Figure 107 is an illustration of the Environmental Statistics page. Figure 107: Environmental statistics Network Storage Router M2402 User Guide...
Page 180: Viewing Fibre Channel Status Information
Display Fibre Channel Resource Status (3) displays Fibre Channel resource transport information. Display Fibre Channel Driver Resource Status (4) displays Fibre Channel driver information. Each menu option and example screen displays are discussed in the following sub-sections. Network Storage Router M2402 User Guide...
Page 181: Viewing Fibre Channel Link Information
Figure 109: Fibre Channel Link Status screen 2. To view link information for the next Fibre Channel port on this module, press Enter. 3. To refresh the screen display, select Autorepeat A). Network Storage Router M2402 User Guide...
Page 182 BadRxChars Number of bad characters received. LinkFailures Number of Link Failure conditions. BadCRCFrames Number of frames received with a bad CRC. ProtocolErrs Number of protocol errors detected. BadSCSIFrames Number of BAD SCSI frames detected. Network Storage Router M2402 User Guide...
Page 183: Viewing Attached Fibre Channel Devices
In Router-to-Router (R2R) configurations, only the first device of all the attached devices will be shown. To see all of the devices in R2R configurations, use Visual Manage. 4. To view device details, select Display Device Details (D). Network Storage Router M2402 User Guide...
Page 184: Viewing Fibre Channel Resource Transport Information
The FCP Transport Queues page is displayed. The FCP Transport Queue page has no options. It is used only for viewing resource status. Figure 112 is an illustration of the FCP Transport Queue page. Figure 112: FCP Transport queues Network Storage Router M2402 User Guide...
Page 185: Viewing Fibre Channel Driver Status Information
To display SCSI status information, in the System Statistics Menu, select Display Parallel SCSI Protocol Status (4). The Parallel SCSI Protocol Status Menu is displayed. Figure 114 is an illustration of the SCSI Status Menu. Figure 114: SCSI Status menu Network Storage Router M2402 User Guide...
Page 186: Viewing Scsi Statistics
Issue discovery for selected bus (2) issues a discovery command for the selected bus. Issue boot discovery (3) issues a boot discovery command. Display all local devices (4) displays a list of local devices for all buses. Network Storage Router M2402 User Guide...
Page 187: Viewing Scsi Resource Information
The SCSI Resource Display page is displayed. There are no options in the SCSI Resource Display. It is used only for viewing SCSI resource status. Figure 116 is an illustration of the SCSI Resource Display page. Figure 116: SCSI Resource display Network Storage Router M2402 User Guide...
Page 188: Event Log
Event Log Menu. Figure 117: Event Log menu Event Log Menu options: Display event log (1) displays the Event Log. Clear event log (2) deletes all entries from the Event Log. Network Storage Router M2402 User Guide...
Page 189: Beacon Settings
Beacon Settings Menu. Figure 118: Beacon Settings menu Note: Whenever the router is rebooted, the Beacon Mode is automatically turned off. To change the setting, enter Toggle Beacon Settings (1). Options are On and Off. Network Storage Router M2402 User Guide...
Page 190: Trace Dump Menu
Using an FTP session, the trace buffers from the router can be copied and saved. 1. Verify the router is connected to the Ethernet network. 2. Start an FTP session. 3. At the FTP prompt, enter the router IP address: ftp <IP address> Network Storage Router M2402 User Guide...
Page 191 6. Specify Bin mode: 7. To copy the current trace buffer: get curtrace.txt The file will transfer from the router. 8. To copy the previous trace buffer: get prvtrace.txt The file will transfer from the router. Network Storage Router M2402 User Guide...
Page 192: Reboot Option
FLASH, and boots using the new image. Figure 120 is an illustration of the Download Firmware Menu after a new version of the firmware has been loaded. Network Storage Router M2402 User Guide...
Page 193 Serial/Telnet User Interface Figure 120: Download Firmware menu Network Storage Router M2402 User Guide...
Page 194 Serial/Telnet User Interface Network Storage Router M2402 User Guide...
Page 195: Ftp User Interface
The following tasks can be managed through an FTP interface: Accessing the FTP UI Backing Up and Restoring Configuration Settings Copying Trace Buffers Upgrading Firmware Each of these procedures is discussed in this chapter. Network Storage Router M2402 User Guide...
Page 196: Accessing The Ftp Ui
You may also need to specify the external directory location where your FTP utility will store the backup configuration file. 3. Enter the user name and password. The default user name is and the default password is root password Network Storage Router M2402 User Guide...
Page 197: Backing Up And Restoring Configuration Settings
The default user name is and the default password is root password HP recommends that the user name and password be changed from the default values. 4. Specify binary mode: 5. Specify the filename (with the extension .cfg) using the get command: get filename.cfg...
Page 198: Restoring The Router Configuration
The default user name is and the default password is root password HP recommends that the user name and password be changed from the default values. 4. Specify binary mode: 5. Specify the configuration’s path and filename (with the filename extension .cfg) using the put command:...
Page 199: Copying Trace Buffers
The default user name is and the default password is root password HP recommends that the user name and password be changed from the default values. 4. Specify binary mode: 5. Specify the filename (with the extension .txt) using the get command.
Page 200: Upgrading Firmware
The default user name is and the default password is root password HP recommends that the user name and password be changed from the default values. 4. Specify binary mode: 5. Specify the path and filename (extension .dlx) of the firmware file to be transferred by using the put command as shown: put <path:filename.dlx>...
Page 201 Hardware Module Replacement This chapter fred the procedures for installing and removing hardware modules of the StorageWorks Network Storage Router M2402. Included topics: Removing and Installing a Power Module or Power Bay Cover Removing and Installing the Fan Module Removing and Installing an I/O Module or Blank I/O Module...
Page 202: Hardware Module Replacement
Removing a power module Caution: If it is necessary to remove the power module in a single power supply system, HP recommends first powering-down the router. Be sure all data movement operations are suspended during this time. Network Storage Router M2402 User Guide...
Page 203: Removing A Power Module Or Power Bay Cover
The thumbscrews cannot be physically detached from the modules, but can be loosened so that the power module or power bay cover can be removed, as described in Step 2. Figure 122: Thumbscrews and handle of a power module Network Storage Router M2402 User Guide...
Page 204 Caution: Power bays must either have a power module or power bay cover installed to ensure proper cooling. If proper cooling is not maintained, the router could overheat and automatically power off. Network Storage Router M2402 User Guide...
Page 205: Installing A Power Module Or Power Bay Cover
To install a power bay cover, carefully slide the cover so that it clips onto the left side of the power bay. Verify the orientation of the warning message as seen in Figure 123. 4. Tighten the thumbscrews on the power module or power bay cover. Network Storage Router M2402 User Guide...
Page 206: Removing And Installing The Fan Module
Removing the Fan Module To remove a fan module, press the fan module latches inward 1 and while holding the latches in, pull the fan module outward. Figure 124 for an illustration of removing a fan module. Network Storage Router M2402 User Guide...
Page 207: Installing The Fan Module
3. Insert the new fan module into the fan bay, using the orientation shown in Figure 125, Installing a Fan Module. Push the module into position until the fan latches lock into place. Network Storage Router M2402 User Guide...
Page 208 4. Verify the newly installed fan module is functioning properly by viewing the Environmental Statistics screen of the Serial/Telnet user interface or the Report Screen of the Visual Manager user interface. These display screens confirm that each fan in the module is rotating. Network Storage Router M2402 User Guide...
Page 209: Removing And Installing An I/O Module Or Blank I/O Module
I/O modules must be installed or removed when the router is powered off. Installing I/O modules while power is applied may result in damage to the module or system. Failure to do so may void the product warranty. Network Storage Router M2402 User Guide...
Page 210: Removing An I/O Module Or Blank Module
I/O bay. Caution: I/O bays must either have an I/O module or I/O module blank installed to ensure proper cooling. If proper cooling is not maintained, the router could overheat and automatically power off. Network Storage Router M2402 User Guide...
Page 211: Installing An I/O Module Or Blank Module
Figure 128 illustrates a SCSI module and Figure 129 illustrates a Fibre Channel module. Figure 128: Thumbscrews and handle on a SCSI module Network Storage Router M2402 User Guide...
Page 212 Failure to properly install a module may result in damage to the module or router and may void your service warranty. 5. Tighten the thumbscrews on the new I/O module or blank module until secure. Network Storage Router M2402 User Guide...
Page 213: Basic Troubleshooting
Basic Troubleshooting This chapter discusses some basic methods of identifying faults in the setup and configuration of the StorageWorks Network Storage Router M2402. Most problems are made during the initial installation of the router. Before proceeding with advanced troubleshooting techniques, verify all connections and review the configuration.
Page 214: Led Indicators
When the LED continuously alternates between green and amber, this indicates the router is in Beaconing Mode. Additional information and illustrations of the specific LEDs is available in Chapter 1, “Introduction.” Network Storage Router M2402 User Guide...
Page 215: Basic Troubleshooting
Bus Type—On an LVD SCSI module, SE and LVD devices can be connected to the same bus. However, if one SE device is detected during power up, communication to all devices will convert to SE mode. Network Storage Router M2402 User Guide...
Page 216: Verifying Fibre Channel Connection
Channel port speed must be manually set, such as for 2 Gb/s. If set incorrectly and plugged into a Loop or Fabric, the unit may receive Framing errors due to the incorrect Fibre Channel link speed. Network Storage Router M2402 User Guide...
Page 217: Verifying Scsi Devices In Windows Nt
Caution: Restoring factory defaults overwrites user configurations. In the serial/ Telnet interface, use the save configuration option before resetting factory defaults, to allow recovery of user configuration. Network Storage Router M2402 User Guide...
Page 218: Verifying Mapping
Verifying HBA Device Driver Information Review the HBA device driver Readme.txt file for configuration specifics. An HBA may require a different configuration. HBAs typically come with utility programs to view or change their configurations. Network Storage Router M2402 User Guide...
Page 219: Verifying Serial Port Configuration
Target bit SET and the Initiator bit CLEAR. However, some configurations require the Initiator bit be SET, such as in router-to-router configurations. See the Fibre Channel configuration sections of Chapter 4, “Visual Manager User Interface,” or Chapter 5, “Serial/Telnet User Interface,” for information. Network Storage Router M2402 User Guide...
Page 220 Page Length 0x10 Payload Length 0x10 Type Code Type Code Extension Response Code Originator Process Associator Responder Process Associator Initiator Function Target Function Command/Data Mixed Allowed Data/Response Mixed Allowed Read XFER_RDY Disabled Write XFER_RDY Disabled Network Storage Router M2402 User Guide...
Page 221: A Serial And Ethernet Pin Assignments
Serial and Ethernet Pin Assignments This appendix provides details for: DB-9 serial pin assignments RJ-45 Ethernet pin assignments Network Storage Router M2402 User Guide...
Page 222: Db-9 Serial Pin Assignments
Transmit Data No Connection Ground No Connection RTS (Request to Send) Unused CTS (Clear to Send) Unused No Connection Note: To connect the router to a host system, use a RS-232 null modem cable. Network Storage Router M2402 User Guide...
Page 223: Rj-45 Ethernet Cable Pin Assignments
The router Ethernet connection supports the IEEE specifications for 10BASE-T and 100BASE-TX Ethernet standards. Figure 131: RJ-45 Ethernet pin assignments Pin Number Function Transmit Out + Transmit Out - Receive in + No Connection No Connection Receive in - No Connection No Connection Network Storage Router M2402 User Guide...
Page 224 Serial and Ethernet Pin Assignments Network Storage Router M2402 User Guide...
Page 225: Controller Lun Commands
Controller LUN Commands The StorageWorks Network Storage Router M2402 supports and executes the set of SCSI-3 commands listed in this Appendix. These commands can be received as FCP commands over the Fibre Channel bus and are supported by the Controller LUNs.
Page 226: General Commands
The format of the Report LUNs command is shown in Table Table 7: Format of Report LUNs Command Bit/Byte Operation Code (Example: 0xA0) Reserved Reserved Reserved Reserved Reserved Most Significant Byte (MSB) Allocation Length Least Significant Byte (LSB) Reserved Control Byte Network Storage Router M2402 User Guide...
Page 227: Inquiry Command
Inquiry Command The format of the Inquiry Command is shown in Table Table 9: Format of LUN Inquiry Command Bit/Byte Operation Code (Example: 0x12) Reserved EVPD Page Code or Operation Code Reserved Allocation Length Control Network Storage Router M2402 User Guide...
Page 228: Evpd Page 0X80
Device Type Qualifier 0x00 ISO Version 0x00 AENC 0x00 TrmIOP 0x00 Response Data Format 0x02 – SCSI-2 Inquiry Data Format Additional Length 0x20 RelAdr 0x00 Wbus32 0x00 Sync 0x00 Linked 0x00 CmdQue 0x00 SftRe 0x00 Network Storage Router M2402 User Guide...
Page 229: Copy Manager Commands
The router supports Extended Copy commands in the following two formats: Version 99-143r1 Version SPC-2 To initiate Extended Copy operations, the commands can be sent to any tape device LUN attached to the router. Multiple concurrent Extended Copy commands can be active. Network Storage Router M2402 User Guide...
Page 230: Version 99-143R1
Table 13: Extended Copy Initiator descriptor codes, version 99-143r1 Item Value Block to Stream 0x00 Stream to Block 0x01 Block to Block 0x02 Inline to Stream 0x04 Stream to Discard 0x06 Verify Target 0x07 Space Operation 0x11 Locate Operation 0x12 Network Storage Router M2402 User Guide...
Page 231: Version Spc-2
Stream to Stream 0x03 Inline Data to Stream 0x04 Stream to Discard 0x06 Verify Target 0x07 Block with Offset to Stream 0x08 Stream to Discard + Hold 0x0f Space Operation 0x11 Locate Operation 0x12 Network Storage Router M2402 User Guide...
Page 232: Receive Copy Results Command
Failed Segment DetailsS 0x04 Mode Sense (6) and Mode Sense (10) Commands The router supports the Mode Sense (6) and Mode Sense (10) commands, used in conjunction with the 99-143r1 version of Extended Copy command. Network Storage Router M2402 User Guide...
Page 233: C Addressing Methods And Table Structures
Table 23. First level addressing is supported, so only the first two bits of the 8 bit FCP LUN are used. Table 18: Addressing Sequence Bit/Byte Address Method Address Method Specific Address Mothod Specific Network Storage Router M2402 User Guide...
Page 234 The administrator enters the node number (number to the left of the colon in Table 22) and the router translates the node number into the corresponding AL_PA value (number to the right of the colon in Table 22). Network Storage Router M2402 User Guide...
Page 235 57:0x6C 78:0x9B 99:0xBA 120:0xE0 16:0x29 37:0x4B 58:0x6D 79:0x9D 100:0xBC 121:0xE1 17:0x2A 38:0x4C 59:0x6E 80:0x9E 101:0xC3 122:0xE2 18:0x2B 39:0x4D 60:0x71 81:0x9F 102:0xC5 123:0xE4 19:0x2C 40:0x4E 61:0x72 82:0xA3 103:0xC6 124:0xE8 20:0x2D 41:0x51 62:0x73 83:0xA5 104:0xC7 125:0xEF Network Storage Router M2402 User Guide...
Page 236: Scc (Scsi Controller Command) Addressing Method
Report LUNs command. This command is sent to the router (using the Peripheral Device Addressing method). The router returns a table indicating the attached devices. The host can then perform actions on these devices directly without performing further discovery processing. Network Storage Router M2402 User Guide...
Page 237: Auto Assigned Addressing Method
Initiator ID per bus, multiplied by the number of LUNs per target. The index table can be manually edited. A method is also provided to perform SCSI device discovery and fill the index table. Table 23 for the Indexed addressing table. Network Storage Router M2402 User Guide...
Page 238 Addressing Methods and Table Structures Table 23: Indexed Addressing Table FCP LUN Value SCSI BUS:TARGET:LUN 0:0:0 0:1:0 0:2:0 0:3:0 0:4:0 0:5:0 0:6:0 (0:7:0 occupied by Initiator ID) 0:8:0 (...) (...) 0:14:0 0:15:0 1:0:0 1:1:0 1:2:0 (...) (...) Network Storage Router M2402 User Guide...
Page 239: D Snmp Management Information Bases
SNMP Management Information Bases The StorageWorks Network Storage Router M2402 (router) supports two Simple Network Management Protocol (SNMP) Management Information Bases (MIB): Fibre Alliance (MIB) Enterprise (MIB) An MIB contains complete descriptions of the different types of information that can be exchanged between the router and a management application using SNMP.
Page 240: Fibre Alliance Mib
Router basic information settings include the router name and information, contact information, and location information. To set basic router information: 1. Access the Fibre Alliance MIB. 2. Go to the connUnitTable in the Fibre Alliance MIB. 3. Go to the connUnitName leaf. Network Storage Router M2402 User Guide...
Page 241: Setting Port Name Information
Setting Port Name Information HP recommends naming ports based on the type of device that is connected to that port. For example, a port connected to a terabyte RAID storage array could be named something to reflect this identity.
Page 242: Viewing The Router Event Log
Utilities node provides information about the current status of the router, port and bus statistics, and various system logs that can be used for diagnostics. For more information on accessing the Enterprise MIB, contact a systems services representative. Network Storage Router M2402 User Guide...
Page 243: Fibre Alliance Mib 2.2 Table
LEAF DisplayString 1.3.6.1.3.94.1.6.1.11 connUnitDomainId LEAF DisplayString 1.3.6.1.3.94.1.6.1.12 connUnitProxyMaster LEAF INTEGER 1.3.6.1.3.94.1.6.1.13 connUnitPrincipal LEAF INTEGER 1.3.6.1.3.94.1.6.1.14 connUnitNumSensors LEAF INTEGER 1.3.6.1.3.94.1.6.1.15 connUnitStatusChangeTime LEAF TimeTicks 1.3.6.1.3.94.1.6.1.16 connUnitConfigurationChangeTime LEAF TimeTicks 1.3.6.1.3.94.1.6.1.17 connUnitNumRevs LEAF INTEGER 1.3.6.1.3.94.1.6.1.18 connUnitNumZones LEAF INTEGER Network Storage Router M2402 User Guide...
Page 244 1.3.6.1.3.94.1.8.1.5 connUnitSensorInfo LEAF DisplayString 1.3.6.1.3.94.1.8.1.6 connUnitSensorMessage LEAF DisplayString 1.3.6.1.3.94.1.8.1.7 connUnitSensorType LEAF INTEGER 1.3.6.1.3.94.1.8.1.8 connUnitSensorCharacteristic LEAF INTEGER 1.3.6.1.3.94.1.10 connUnitPortTable NODE 1.3.6.1.3.94.1.10.1 connUnitPortEntry NODE 1.3.6.1.3.94.1.10.1.1 connUnitPortUnitId LEAF DisplayString 1.3.6.1.3.94.1.10.1.2 connUnitPortIndex LEAF INTEGER 1.3.6.1.3.94.1.10.1.3 connUnitPortType LEAF INTEGER Network Storage Router M2402 User Guide...
Page 245 LEAF TimeTicks 1.3.6.1.3.94.1.11.1.6 connUnitEventSeverity LEAF FcEventSeverity 1.3.6.1.3.94.1.11.1.7 connUnitEventType LEAF INTEGER 1.3.6.1.3.94.1.11.1.8 connUnitEventObject LEAF OBJECT IDENTIFIER 1.3.6.1.3.94.1.11.1.9 connUnitEventDescr LEAF DisplayString 1.3.6.1.3.94.1.12 connUnitLinkTable NODE 1.3.6.1.3.94.1.12.1 connUnitLinkEntry NODE 1.3.6.1.3.94.1.12.1.1 connUnitLinkUnitId LEAF DisplayString 1.3.6.1.3.94.1.12.1.2 connUnitLinkIndex LEAF INTEGER Network Storage Router M2402 User Guide...
Page 246 1.3.6.1.3.94.4.1 connUnitPortStatHubTable NODE 1.3.6.1.3.94.4.1.1 connUnitPortStatHubEntry NODE 1.3.6.1.3.94.4.1.1.1 connUnitPortStatHubUnitId LEAF DisplayString 1.3.6.1.3.94.4.1.1.2 connUnitPortStatHubIndex LEAF INTEGER 1.3.6.1.3.94.4.1.1.3 connUnitPortStatHubCountError LEAF DisplayString 1.3.6.1.3.94.4.1.1.4 connUnitPortStatHubCountTxFrame LEAF DisplayString 1.3.6.1.3.94.4.1.1.5 connUnitPortStatHubCountRxFrame LEAF DisplayString 1.3.6.1.3.94.4.1.1.6 connUnitPortStatHubCountTxOctets LEAF DisplayString 1.3.6.1.3.94.4.1.1.7 connUnitPortStatHubCountRxOctets LEAF DisplayString Network Storage Router M2402 User Guide...
Page 247 LEAF INTEGER 1.3.6.1.3.94.4.4.1.3 connUnitPortStatLANCountError LEAF DisplayString 1.3.6.1.3.94.4.4.1.4 connUnitPortStatLANCountTxPacket LEAF DisplayString 1.3.6.1.3.94.4.4.1.5 connUnitPortStatLANCountRxPacket LEAF DisplayString 1.3.6.1.3.94.4.4.1.6 connUnitPortStatLANCountTxBytes LEAF DisplayString 1.3.6.1.3.94.4.4.1.7 connUnitPortStatLANCountRxBytes LEAF DisplayString 1.3.6.1.4 private NODE 1.3.6.1.4.1 enterprises NODE 1.3.6.1.5 security NODE 1.3.6.1.6 snmpV2 NODE Network Storage Router M2402 User Guide...
Page 248 Table 24: Fibre Alliance MIB Table Name Type 1.3.6.1.6.1 snmpDomains NODE 1.3.6.1.6.1.1 snmpUDPDomain NODE 1.3.6.1.6.1.2 snmpCLNSDomain NODE 1.3.6.1.6.1.3 snmpCONSDomain NODE 1.3.6.1.6.1.4 snmpDDPDomain NODE 1.3.6.1.6.1.5 snmpIPXDomain NODE 1.3.6.1.6.2 snmpProxys NODE 1.3.6.1.6.2.1 rfc1157Proxy NODE 1.3.6.1.6.2.1.1 rfc1157Domain NODE 1.3.6.1.6.3 snmpModules NODE Network Storage Router M2402 User Guide...
Page 249: Enterprise Mib Table
NODE 1.3.6.1.4.1.2512.1.1.1.3.2.1 fcPortEntry NODE 1.3.6.1.4.1.2512.1.1.1.3.2.1.2 fcPortNumber LEAF Unsigned32 1.3.6.1.4.1.2512.1.1.1.3.2.1.3 fcPortName LEAF OCTET STRING 1.3.6.1.4.1.2512.1.1.1.3.2.1.4 fcLinkStatus LEAF INTEGER 1.3.6.1.4.1.2512.1.1.1.3.2.1.5 fcPortId LEAF OCTET STRING 1.3.6.1.4.1.2512.1.1.1.3.2.1.6 fcUseHardALPA LEAF INTEGER 1.3.6.1.4.1.2512.1.1.1.3.2.1.7 fcDiscoveryMode LEAF INTEGER 1.3.6.1.4.1.2512.1.1.1.3.2.1.8 fcBufferedTapeWrites LEAF INTEGER Network Storage Router M2402 User Guide...
Page 250 LEAF INTEGER verride 1.3.6.1.4.1.2512.1.1.1.4.3.1.3 scsiTargetOverrideCDBGroup6L LEAF INTEGER engthDefault 1.3.6.1.4.1.2512.1.1.1.4.3.1.4 scsiTargetOverrideCDBGroup7L LEAF INTEGER engthDefault 1.3.6.1.4.1.2512.1.1.1.4.3.1.5 scsiTargetOverrideWideNegotia LEAF INTEGER tion 1.3.6.1.4.1.2512.1.1.1.4.3.1.6 scsiTargetOverrideSynchronous LEAF INTEGER Negotiation 1.3.6.1.4.1.2512.1.1.1.4.3.1.7 scsiTargetOverrideSynchronousP LEAF INTEGER arameterOverride 1.3.6.1.4.1.2512.1.1.1.4.3.1.8 scsiTargetOverrideSynchronousP LEAF INTEGER eriod Network Storage Router M2402 User Guide...
Page 251 1.3.6.1.4.1.2512.1.1.2.2.2 snmpCommunityNameGet LEAF OCTET STRING 1.3.6.1.4.1.2512.1.1.2.2.3 snmpCommunityNameSet LEAF OCTET STRING 1.3.6.1.4.1.2512.1.1.2.2.4 snmpTrapManagerTable NODE 1.3.6.1.4.1.2512.1.1.2.2.4.1 snmpTrapManagerEntry NODE 1.3.6.1.4.1.2512.1.1.2.2.4.1.1 snmpTrapManagerIndex LEAF INTEGER 1.3.6.1.4.1.2512.1.1.2.2.4.1.2 snmpTrapManagerIpAddress LEAF IpAddress 1.3.6.1.4.1.2512.1.1.2.2.4.1.3 snmpTrapManagerFilter LEAF INTEGER 1.3.6.1.4.1.2512.1.1.2.2.4.1.4 snmpTrapManagerRowState LEAF INTEGER 1.3.6.1.4.1.2512.1.1.2.3 NODE Network Storage Router M2402 User Guide...
Page 252 LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.2.1.4 scsiInitiatorBus LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.2.1.5 scsiHostInitiatorId LEAF INTEGER 1.3.6.1.4.1.2512.1.2.2.1.6 scsiInitiatorCurMap LEAF OCTET STRING 1.3.6.1.4.1.2512.1.2.3 fcDeviceTable NODE 1.3.6.1.4.1.2512.1.2.3.1 fcDeviceEntry NODE 1.3.6.1.4.1.2512.1.2.3.1.1 fcDeviceIndex LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.3.1.2 fcDeviceModule LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.3.1.3 fcDevicePort LEAF Unsigned32 Network Storage Router M2402 User Guide...
Page 253 LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.5.1.1.2 scsiMapDeviceIndex LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.5.1.1.3 fcScsiMapName LEAF OCTET STRING 1.3.6.1.4.1.2512.1.2.5.2 scsiFcMappingTable NODE 1.3.6.1.4.1.2512.1.2.5.2.1 scsiFcMappingEntry NODE 1.3.6.1.4.1.2512.1.2.5.2.1.1 scsiTargetId LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.5.2.1.2 scsiTargetLUN LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.5.2.1.3 fcMapDeviceIndex LEAF Unsigned32 1.3.6.1.4.1.2512.1.2.5.2.1.4 scsiFcMapName LEAF OCTET STRING Network Storage Router M2402 User Guide...
Page 254 NODE 1.3.6.1.4.1.2512.1.3.1.2.1 fcStats NODE 1.3.6.1.4.1.2512.1.3.1.2.1.1 fcStatsTable NODE 1.3.6.1.4.1.2512.1.3.1.2.1.1.1 fcStatsEntry NODE 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.1 fcStatsInDeviceDataSequences LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.2 fcStatsOutDeviceDataSequences LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.3 fcStatsInLinkDataSequences LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.4 fcStatsOutLinkDataSequences LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.5 fcStatsInPBSYFrames LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.6 fcStatsOutPBSYFrames LEAF Unsigned32 Network Storage Router M2402 User Guide...
Page 255 LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.2 fcStatsBadSCSIFrames LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.1.1.1.2 fcStatsActiveLUN LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.2 scsiStats NODE 1.3.6.1.4.1.2512.1.3.1.2.2.1 scsiBusStatsTable NODE 1.3.6.1.4.1.2512.1.3.1.2.2.1.1 scsiBusStatsEntry NODE 1.3.6.1.4.1.2512.1.3.1.2.2.1.1.1 scsiBusStatsMode LEAF INTEGER 1.3.6.1.4.1.2512.1.3.1.2.2.1.1.2 scsiBusStatsResets LEAF Unsigned32 1.3.6.1.4.1.2512.1.3.1.2.2.2 scsiTgtStatsTable NODE 1.3.6.1.4.1.2512.1.3.1.2.2.2.1 scsiTgtStatsEntry NODE Network Storage Router M2402 User Guide...
Page 256 LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.6 tracePSManagement LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.7 tracePSDriver LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.8 traceSGList LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.9 traceAF LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.10 traceInband LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.13 traceTiming LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.14 traceFCPRMI LEAF INTEGER 1.3.6.1.4.1.2512.1.3.2.15 traceCurrentTable NODE Network Storage Router M2402 User Guide...
Page 257 STRING 1.3.6.1.4.1.2512.1.3.3.2.1.5 eventLogSev LEAF Integer32 1.3.6.1.4.1.2512.1.3.3.2.1.6 eventLogDesc LEAF OCTET STRING 1.3.6.1.5 security NODE 1.3.6.1.6 snmpV2 NODE 1.3.6.1.6.1 snmpDomains NODE 1.3.6.1.6.1.1 snmpUDPDomain NODE 1.3.6.1.6.1.2 snmpCLNSDomain NODE 1.3.6.1.6.1.3 snmpCONSDomain NODE 1.3.6.1.6.1.4 snmpDDPDomain NODE 1.3.6.1.6.1.5 snmpIPXDomain NODE Network Storage Router M2402 User Guide...
Page 258 SNMP Management Information Bases Table 25: Enterprise MIB Table Name Type 1.3.6.1.6.2 snmpProxys NODE 1.3.6.1.6.2.1 rfc1157Proxy NODE 1.3.6.1.6.2.1.1 rfc1157Domain NODE 1.3.6.1.6.3 snmpModules NODE Network Storage Router M2402 User Guide...
Page 259: Regulatory Compliance Notices
Regulatory Compliance Identification Numbers For the purpose of regulatory compliance certifications and identification, your product has been assigned a unique HP Series Number. The series number can be found on the product label, along with the required approval markings and information.
Page 260: Federal Communications Commission Notice
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. Network Storage Router M2402 User Guide...
Page 261: Class B Equipment
For questions regarding this FCC declaration, contact us by mail or telephone: Hewlett-Packard Computer Corporation P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 1-281-514-3333 To identify this product, refer to the part, series, or model number found on the product. Network Storage Router M2402 User Guide...
Page 262: Modifications
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Network Storage Router M2402 User Guide...
Page 263: Canadian Notice (Avis Canadien)
EN55022 (CISPR 22) – Electromagnetic Interference EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11) – Electromagnetic Immunity EN61000-3-2 (IEC61000-3-2) – Power Line Harmonics EN61000-3-3 (IEC61000-3-3) – Power Line Flicker EN60950 (IEC950) – Product Safety Network Storage Router M2402 User Guide...
Page 264: Japanese Notice
Regulatory Compliance Notices Japanese Notice Network Storage Router M2402 User Guide...
Page 265: Taiwanese Notice
Regulatory Compliance Notices Taiwanese Notice Laser Device All HP systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product. The product does not emit hazardous light;...
Page 266: Compliance With International Regulations
All HP systems equipped with laser devices comply with appropriate safety standards including IEC 825. Laser Product Label The following label or equivalent is located on the surface of the HP supplied laser device. This label indicates that the product is classified as a CLASS 1 LASER PRODUCT.
Page 267 Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. Place parts on a grounded surface before removing them from their containers. Avoid touching pins, leads, or circuitry. Always be properly grounded when touching a static-sensitive component or assembly. Network Storage Router M2402 User Guide...
Page 268: Grounding Methods
If you do not have any of the suggested equipment for proper grounding, have a HP authorized reseller install the part. Note: For more information on static electricity, or assistance with product installation, contact your HP authorized reseller. Network Storage Router M2402 User Guide...
Page 269 Serial/Telnet UI Fibre Channel Visual Manager UI power cord bezel, attaching to the rack, illustrated SCSI blank I/O module serial installing controller LUN commands removing copy manager commands, listed buffered tape writes extended copy Network Storage Router M2402 User Guide...
Page 270 Serial/Telnet UI Visual Manager UI Visual Manager UI external features, overview discovery mode Fibre Channel Serial/Telnet UI factory settings, resetting Visual Manager UI Serial/Telnet UI overview of Visual Manager UI SCSI fan module Serial/Telnet UI Network Storage Router M2402 User Guide...
Page 271 Serial/Telnet UI deleting entries Visual Manager UI Serial/Telnet UI port name Visual Manager UI Serial/Telnet UI editing entries Visual Manager UI Serial/Telnet UI thumbscrews and handle, illustrated Visual Manager Fibre Channel port, illustrated filling entries Network Storage Router M2402 User Guide...
Page 272 Serial/Telnet UI installing the router Visual Manager UI desktop editing, SCSI rack Serial/Telnet UI interfaces Visual Manager UI types of connections selecting a host for the current map user, listed Network Storage Router M2402 User Guide...
Page 273 Serial/Telnet UI Serial/Telnet UI Visual Manager editing entries changing the name of the host Serial/Telnet UI Visual Manager editing host information clearing entries Serial/Telnet UI Serial/Telnet UI editing the current map Network Storage Router M2402 User Guide...
Page 274 Serial/Telnet UI RJ-45 Ethernet Visual Manager UI pin layout viewing and changing DB-9 serial Visual Manager UI RJ-45 Ethernet maps port locations, illustrated auto-assigned, defined port mode, Fibre Channel indexed, defined Serial/Telnet UI overview Network Storage Router M2402 User Guide...
Page 275 Serial/Telnet UI rails, separating, illustrated Visual Manager UI rebooting clearing entries Serial/Telnet UI Serial/Telnet UI Visual Manager UI Visual Manager UI regulatory compliance notices creating entries Canadian Serial/Telnet UI device modifications Visual Manager UI Network Storage Router M2402 User Guide...
Page 276 Visual Manager UI event log LED indicators clearing override settings configuration of Visual Manager UI viewing termination mode event settings, configuration of Visual Manager UI factory settings, resetting thumbscrews and handle, illustrated Fibre Channel devices, viewing Network Storage Router M2402 User Guide...
Page 277 System Statistics Menu, options, listed options, listed system status information initial access System Utilities Menu, options, listed listed System Utility Menu, described Network Storage Router M2402 User Guide...
Page 278 Serial/Telnet UI Edit Map Entries for a SCSI menu, illustrated Map, illustrated Serial/Telnet UI SCSI Resource Display screen, Serial/Telnet UI editing host information on a illustrated SCSI module, illustrated Serial/Telnet UI SCSI Status Menu, illustrated Serial/Telnet UI entire device list, illustrated Network Storage Router M2402 User Guide...
Page 279 Serial/Telnet UI configuration of Visual Manager UI Serial/Telnet UI subnet mask Visual Manager UI Serial/Telnet UI copying buffers Visual Manager UI viewing symbols in text xiii Serial/Telnet UI symbols on equipment troubleshooting basic steps, listed Network Storage Router M2402 User Guide...
Page 280 Visual Manager Fibre Channel Host Name clock configuration dialog box, illustrated discovery Visual Manager Fibre Channel Map dialog Ethernet configuration box, illustrated DHCP Visual Manager FTP Utility screen, illustrated Ethernet mode Network Storage Router M2402 User Guide...
Page 281 Fibre Channel and SCSI System Menu adding a new host options adding a new map traces deleting a host clearing buffers deleting a map configuration selecting a host displays XE selecting a map user configuration Network Storage Router M2402 User Guide...
Page 282 Visual Manager Utilities Menu, illustrated HP storage Visual Manager World Wide Node Name wrist straps screen using WWN configuration Serial/Telnet UI Visual Manager UI warning WWN label, illustrated rack stability symbols on equipment Network Storage Router M2402 User Guide...

HP M2402 User Manual

1 Introduction

2 Installation

3 Configuration Overview

4 Visual Manager User Interface

5 Serial/Telnet User Interface

6 FTP User Interface

7 Hardware Module Replacement

8 Basic Troubleshooting

Quick Links

Troubleshooting

Related Manuals for HP M2402

Summary of Contents for HP M2402