Advertisement
Document No. 540-742
Installation Instructions
January 5, 2012
Accessories
Table 4. Room Sensor Pre-terminated Cables.
TEC Product Number
Vinyl
Plenum
Plenum Only
540-130
540-135 or
588-100A
540-131
540-136 or
588-100B
540-132
540-137 or
588-100C
P/N
Description
182-621
Gym Guard Kit, desert beige
182-621E
Gym Guard Kit, satin chrome
182-683
Metal (and Wood) Stud Mounting
Bracket (pkg. 5)
182-685
Spring Clips: Finished Drywall
Mounting Kit
(10 pack)
192-506
Electrical Box Adapter Plate
Assembly Kit (pkg. 5)
192-860
Finish Plate Kit 1 Gang 1 Sensor;
stainless steel
536-666
Mounting Strap
544-782*
Single Adapter Base Mounting Kit
544-783*
Double Adapter Base Mounting Kit
544-784
Non-conduit Rough-in Kit, Double
544-785*
Extender Ring Kit
544-800
Universal Adapter Kit
981-344
Electrical Box Cover Plate Kit
—
Various finish plates
* Product number suffixes indicate color: A = desert beige; B = white (For example, 544-782B)
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models
as design improvements are introduced. L
other countries. Other product or company names mentioned herein may be the trademarks of their respective owners.
© 2012 Siemens Industry, Inc.
Siemens Industry, Inc.
Building Technologies Divisin
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
USA
LTEC
Product
Description
Number
588-100A
25-foot (7.6 m)
cable with
connections
588-100B
50-foot (15.2 m)
cable with
connections
588-100C
100-foot (30.5 m)
cable with
connections
Gyms and similar environments requiring a guard. (Incompatible
with adapter bases and the extender ring.)
See Part Number 182-621.
Single-sensor rough-in installations. Kit includes locator.
Drywall mounting.
Electrical boxes mounted flush with the wall and for gyms and
similar environments requiring a guard. (Also see Part Number
544-782.)
Single-sensor, low-cost mounting. Plate is 3.7 × 5.1 inches
(9.5 × 12.9 cm).
Standard light switch plate (field-supplied) to mount sensor on 2 × 4
electrical box.
2 x 4 boxes, all single sensor installations on walls with oversized
holes, paint lines, etc., that need to be covered, and on exterior
brick/cement-type walls. Kit includes Electrical Box Adapter Plate
Assembly (Part Number 192-495. Adapter base is 3-1/2 × 5 inches
(8.8 × 12.7 cm).
4 × 6 boxes and all double sensor installations on walls with
oversized holes, paint lines, etc., that need to be covered, and on
exterior brick/cement-type walls. Kit includes two mounting plates
(Part Number 192-720). Adapter base is 5 × 7 inches
(12.7 × 18 cm).
Double-sensor non-conduit rough-in installations. Kit includes
locator.
Exterior brick or cement-type walls; fits to back of sensor base
plate.
Retrofitting a previous horizontal installation to a vertical one, or
when the screw spacing does not fit the electrical box adapter plate.
Kit includes multi-slotted adapter plate.
2 × 4 box rough-ins. Kit includes locator and connector.
Double-sensor, low-cost mounting for a variety of applications.
W
and L
M
ON
ORKS
ON
Your feedback is important to us. If you have
comments about this document, please send them
to
SBT_technical.editor.us.sbt@siemens.com
NOTE:
LTEC cables can be used with either LTEC or
TEC sensors and controllers. However, LTEC
cables must be used with LTEC sensors and
controllers.
Review Table 5 to verify that you have the appropriate
mounting hardware. For retrofit installations, normally follow
the method used by the pre-existing device. You may need
to replace existing mounting hardware. Always mount the
sensor vertically.
Table 5. Mounting Accessories.
Used For
are trademarks of Echelon Corporation registered in the United States and
ARK
Reference
155-222P25 (TB 193)
155-222P25 (TB 193)
129-057
129-073
Figure 4
155-252P25 (TB 238)
540-040; 540-237
Figure 4
Figure 4
540-784
—
Figure 4
—
155-252P25 (TB 238)
Document No. 540-742
Printed in the USA
Page 4 of 4
Advertisement
