Parameter List; Fault Codes - Siemens 6SE2101–1AA01 Operating Manual

8.2 Parameter List

Parameter Description
Only
P00 Frequency, output current or fault code
P01 Low frequency voltage boost
P02 Ramp–up time to maximum frequency
P03 Ramp–down time from maximum frequency
P04 Frequency control mode selection
P05 RUN/STOP mode
P06 Voltage to frequency curve selection
P07 Minimum frequency
P08 Maximum frequency
P09 Digital frequency set–point adjustment
P10 Analogue frequency set–point adjustment
P11 DC injection braking
P12 Jog
P13 Slip compensation
P14 Display status / Analogue output
P15 Voltage to frequency relationship: knee point
P16 Voltage to frequency relationship: curve type
P17 Current limit
P18 Overload limit
P19 Automatic boost
P20 Serial interface selection
P21 Serial interface address
P22 Serial interface parity and baud rate
P23 Digital input response speed
P24 Fixed frequency mode selection
P25 First fixed frequency
P26 Second fixed frequency
P27 Third fixed frequency
P28 Fourth fixed frequency
P29 Skip frequency
P30 Tachometer mode
P31 Tachometer scale factor
P32 Feedback compensation: proportional term (%)
P33 Feedback compensation: integral term (%)
P34 Feedback compensation: differential term (%)
P35 Tachometer slip limit (Hz)
P36 Tachometer sample rate
P37 Display tachometer frequency reading
P40 Switching frequency select
P41 Parameter default values
P42 Auto reset mode
P43 Ramp Smoothing
P44 Tachometer Interface Unit
P45 Clear Text Operator Panel Language
P48 Fault code
P49 Hardware type
P50 Software version
P51 Customer–specific Variants

8.3 Fault Codes

Code Meaning
F00 Excessive load current or excessive link voltage. Low line voltage (6SE210*–3AA01 only).
F01 Excessive heatsink temperature.
F02 Corruption of parameterisation data in the non–volatile memory.
F03 Faulty operation of A–D converter or excessive tachometer feedback voltage.
F04 P07 set to a higher value than P08.
F05 P09 outside the limits set by P07 and P08.
F06 Fault on control board.
F07 Value of P25 > P08 setting or < P07 setting.
F08 Value of P26 > P08 setting or < P07 setting.
F09 Value of P27 > P08 setting or < P07 setting.
F10 Value of P28 > P08 setting or < P07 setting.
F11 Inverter tripped externally via X11.4 input.
8/2
Value Range
00.0 – 30.0%
00.0 – 400 s
00.0 – 400 s
000 – 009
000 – 009
000 – 006
00.0 – 399 Hz
00.1 – 400 Hz
00.0 – 400 Hz
080 – 240%
00.0 – 20.0%
00.1 – 400 Hz
00.0 – 20.0
000 – 003
00.1 – 400 Hz
000 or 001
00.1 – rated output 1.1 x
01.0 – 03.0
000 – 003
000 – 003
000 – 030
000 – 008
000 or 001
000 – 002
00.0 – 400
00.0 – 400
00.0 – 400
00.0 – 400
00.0 – 400
000 – 004
00.1 – 999
000 – 999
000 – 250
000 – 250
00.0 – 20.0
001 – 200
000 – 400
000 – 002
000 or 001
000 – 002
000 – 100
000 – 004
000 or 001
000 – 011
000 – 255
English
Default Settings
[ ] – N. America
00.0
10.0
10.0
000
000
000 [001]
00.1
50.0 [60.0]
50.0 [60.0]
100
00.0
05.0
00.0
000
50.0 [60.0]
000
01.5
000
000
000
000
000
000
00.0
00.0
00.0
00.0
00.0
000
50.0
050
000
000
05.0
001
n/a
000 / 002
000 [001]
000
000
000
n/a
n/a
000