Items For Which User Settings Are Available - Pioneer DDJ-SX2 Service Manual

5

8.3 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE

This unit is provided with user settable items, as shown below.
Although no serious operational problems occur even if data for such user settable items are cleared during repair, it is
recommended that you take note of those settings before starting repair.
Use the Check Sheet, to which you can transcribe the settings.
If the corresponding part or board Assy is replaced for repair, change the user resettable settings to those noted on the Check
Sheet before starting repair. If resetting is not possible, when returning the repaired product, be sure to tell the customer that
the Utility settings have been cleared and will have to be reset, as required.
Item for Which User's
Setting is Available
MIDI controller setting
Channel fader start setting
Crossfader start setting
Attenuator level setting
for the Master output
Flashing setting in Slip mode
Light/flash setting
of the SLIP button
Demo mode setting
SAMPLER Velocity
VELOCITY curve
mode setting
After touch
setting
Operation setting for
NEEDLE SEARCH pad
Cut lag setting for crossfader
Microphone output setting
to Booth monitor
Illuminations White
mode setting illuminations
for jog dial
Red
illuminations
Setting for backspin length
High-pass filter operation
setting for microphone sound
MIDI message operation
setting for crossfader
Jog dial touch sensor
sensitivity adjustment
5
6
Setting Value (The factory default settings are indicated in bold.)
Indication method
Automatically switching modes, according to whether or not Serato DJ is running /
Forced operations to be generally expected from the MIDI controller, regardless
of running or not running of Serato DJ
Right Deck HOT CUE mode button lit / ROLL mode button lit
With SYNC / without SYNC / function disabled
Left Deck Effect parameter: 1 button lit / 2 button lit / 3 button lit
With SYNC / without SYNC / function disabled
Right Deck Effect parameter: 1 button lit / 2 button lit / 3 button lit
0 dB (without attenuation) / –3 dB / –6 dB
Left Deck HOT CUE mode button lit / ROLL mode button lit /
SLICER mode button lit
Flashing enable / Flashing disenable
Left Deck SLIP button lit / SLIP button unlit
The SLIP button to start flashing when Slip mode is entered / The SLIP button to light when
Slip mode is entered and flash while normal playback is being performed in the background
Right Deck SLIP button lit / SLIP button unlit
Time required for start of Demo mode: One minute /5 minutes /
10 minutes of no operation / Demo mode disabled
Right Deck LOOP 2X button lit / LOOP IN button lit / OOP OUT button lit /
LOOP 1/2X button lit
Curve 1 / Curve 2 / Curve 3 / Curve 4
LOOP 2X button lit / LOOP IN button lit / OOP OUT button lit /
LOOP 1/2X button lit
Setting enable / Setting disenable
Left Deck SAMPLER mode button lit / SAMPLER mode button unlit
NEEDLE SEARCH pad operation to be limited /
NEEDLE SEARCH pad operation NOT to be limited
Left Deck CENSOR button lit / CENSOR button unlit
0 (0.5 mm) / 1 (0.6 mm) to 5 (1 mm) to 51 (5.6 mm) / 52 (5.7 mm)
The number of lit segments of the [CH3] channel level indicator denotes a value in tens, and
the number of lit segments of the [CH1] channel level indicator denotes a value in units.
Microphone sound to be output from the [BOOTH OUT] connector /
Microphone sound NOT to be output from the [BOOTH OUT] connector
Right Deck SAMPLER mode button lit / SAMPLER mode button unlit
Decks 1 and 2: Pattern 1 / Pattern 2 / Pattern 3 / Pattern 4 / Pattern 5,
Decks 3 and 4: Pattern 1 / Pattern 2 / Pattern 3 / Pattern 4 / Pattern 5
Left Deck Performance pad: 1 lit / 2 lit / 3 lit / 4 lit / 5 lit,
Right Deck Performance pad: 1 lit / 2 lit / 3 lit / 4 lit / 5 lit
The red illuminations to be lit when the playback position of a track comes close to
a hot cue point / the red illuminations to light or flash in the same way as the SLIP button
Left Deck Performance pad: 6 lit / 7 lit
Backspin length: Short / Normal / Long
Right Deck Performance pad: 6 lit / 7 lit / 8 lit
Enable / disable the high-pass filter for the microphone sound
Left Deck TAP button lit / TAP button unlit
Enable / disable optimization of MIDI messages for the crossfader
Left Deck KEY LOCK button lit / KEY LOCK button unlit
–17 / –16 . . . 0 . . . +16 / +17 (35 steps)
The LEDs at the center of the jog dial: All unlit (–17) to half lit (0) to all lit (+17)
6
7
DDJ-SX2
7
8
Content to
Part Name
be Stored
Utility mode
setting value
IC24
(DSP PCB Assy)
Jog dial touch sensor
sensitivity adjustment
8
A
B
C
D
E
F
47