Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-6071PU...
Page 3
PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4
Charged Section. 607 SCAN B Assy 60 Y DRIVE Assy POWER SUPPLY Unit 60 X DRIVE Assy Conductive plate X 607 SCAN A Assy AC inlet Power switch (S1) Fig. High Voltage Generating Point (Rear view) PDP-6071PU...
Page 5
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. PDP-6071PU...
"OFF" to "ANA AD YCBCR". 3. You can change Mask patterns by pressing [«] to select {SG PATTERN} then using [|] or [\]. Note: When you switch "SG MODE" routes, some displays become monochrome, as they are in Y-signal only mode. PDP-6071PU...
Page 7
2. CMB MASK 01 For use while Combination Mask is displayed. • • • • • Use [»] or [«] to select the type of mask. To "Structure of Layers in Panel Factory Mode 2" 11. CMB MASK 10 PDP-6071PU...
5.2.1 BLOCK DIAGRAM OF THE POWER-DOWN SIGNAL..............103 5.2.2 POWER DOWN OF FAILURE ANALYSIS ..................104 5.3 SHUT DOWN ............................106 5.3.1 BLOCK DIAGRAM OF THE SHUT-DOWN SIGNAL................ 106 5.3.2 SHUT DOWN OF FAILURE ANALYSIS................... 107 5.4 NON-FAILURE SYMPTOMS........................108 PDP-6071PU...
Page 9
10.3 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM ..........191 10.4 LED INFORMATION ..........................192 10.5 SPECIFICATION ABOUT THE THERMAL PROTECTION..............193 10.6 PROCESSING IN ABNORMALITY ......................194 10.7 TRAP SW..............................195 11. SPECIFICATIONS ............................196 11.1 MAIN SPECIFICATIONS ........................196 11.2 ACCESSORIES............................197 11.3 PANEL FACILITIES..........................198 12. IC INFORMATION ............................201 PDP-6071PU...
(In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION 12, 14, 16, 30 Speed clamp ×3 Noise filter for G-Link cable Binder for noise filter Bead band ×3 PDP-6071PU only PDP-6071PU only PDP-6071PU...
Page 11
See Contrast table (2) Cleaning Caution See Contrast table (2) Terminal Position Sheet AAX3330 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description...
2.2 REAR SECTION 22 24 MAIN CN7101 MAIN CN4010 TANSHI CN8801 Refer to "2.3 FRONT SECTION". PDP-6071PU...
Page 13
Caution Label See Contrast table (2) Terminal Display Label A (U/B) AAX3325 Terminal Display Label B50 (U/B) AAX3414 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No.
Note : Take care that the size is different between the coil spring ABH1120 at Front Case and ABH1124 at Mechanical Switch Assy. Refer to P16. 18.2 17.5 ABH1120 ABH1124 for Front Case/ for Mechanical Power Button Switch Assy PDP-6071PU...
Page 15
FRONT SECTION PARTS LIST Mark No. Description Part No. 42 & 60 LED Assy AWW1134 60 IR Assy AWW1137 Front Case Assy 607 AMB2930 Pioneer Name Plate AAM1109 Coil Spring ABH1120 Blind Cushion AEB1449 Nyron Rivet AEC1671 Power Button AAD4147...
-nical Switch Assy and ABH1120 at Front Case . Refer to P14. 18.2 17.5 ABH1120 ABH1124 for Front Case/ for Mechanical Power Button Switch Assy MAIN CN4009 Refer to "2.5 CHASSIS SECTION (2/2)". 49 46 49 31 POWER (*1) PDP-6071PU...
Page 17
Wire Saddle AEC1745 Screw ABA1364 Ferrite Core Holder AEC1818 Re-use Wire Saddle AEC1945 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description /KUC /KUCXC...
6, 35 6, 35 6, 35 6, 35 6, 35 6, 35 6, 35 S a,b 6, 35 AUDIO CN3752 MAIN MAIN CN4008 CN4002 V a,b Power switch AC inlet T a,b U a,b Refer to "2.6 PANEL CHASSIS SECTION". PDP-6071PU...
Page 19
Screw (M3 x 6) ABA1366 10P/5P Housing Wire (J104)(J127) ADX3409 10P/5P Housing Wire (J114)(J128) ADX3410 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description...
2.7 MULTIBASE SECTION 60 DIGITAL CN3001 SIDE KEY CN9501 60 LED CN9801 POWER POWER (side) (Fan) 42 & 60 LED CN9601 POWER POWER SIDE CN9101 PDP-6071PU...
Page 23
Binder AEC-093 Locking Card Spacer AEC1429 Screw PMB30P080FNI Wire Saddle AEC1745 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description /KUC /KUCXC /KUC...
Detach it from the product to be repaired and attach it to the Assy for service. ×4 ×2 ×5 ×4 ×5 ×2 ×2 ×2 ×5 ×4 ×5 ×4 ×2 ×4 ×2 ×2 ×4 ×2 ×4 ×7 ×4 ×4 ×5 ×2 ×4 ×2 ×2 (for transport) PDP-6071PU...
Page 38
AGC1026 Other Resistors RS1/16SS###J IC 3302,3305 PST3628UR IC 3303 SN74AHC08PW IC 3304 PST3610UR CAPACITORS 3301 RN1901 3501–3512,3520–3523 CKSSYB102K50 3302 HN1C01FU [DIGITAL DD CON BLOCK] MISCELLANEOUS MISCELLANEOUS 3302 (102.5 MHz) ASS1188 3601 DD CON UNIT AXY1137 CN 3301 CONNECTOR CKS4835 PDP-6071PU...
Page 39
Q 1207 R5009ANJ Q 1251 DTC143EK Q 1252 DTC123TKA CAPACITORS D 1201,1205 UDZS5R6(B) C 1001,1003 CEHAT470M16 D 1202,1203,1206,1210 CRH01 C 1002,1004,1005 CKSRYB104K16 D 1204,1211 1SS355 C 1006,1007 CCSRCH331J50 D 1207 1SS302 D 1208 UDZS5R1(B) D 1209 UDZS16(B) [X RESONANCE BLOCK] PDP-6071PU...
Page 40
D 1306,1307,1331 1SS355 D 1321,1322 CRF03 [Y RESONANCE BLOCK] D 1323 U1ZB330 SEMICONDUCTORS D 1332 UDZS6R2(B) D 1333 UDZS12(B) IC 2101,2104 TND307TD IC 2102 PS9117 IC 2103,2151 AXF1159 MISCELLANEOUS IC 2181 BA10393F 2101 2SC2412K T 1301 ATK1162 T 1321 ATK1153 PDP-6071PU...
Mark No. Description Part No. 2659 CKSRYB105K10 2661 CCG1186 2682 CKSYB105K25 2683 CKSRYB103K50 2687,2688 CKSRYB104K16 POWER SUPPLY UNIT POWER SUPPLY UNIT has no service part. PDP-6071PU...
Page 45
÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ The encircled numbers denote measuring point in the schematic diagram. Waveforms, refer to service manual (ARP3395). PDP-6071PU...
Signal Scan IC PSUS IC2801 VH IC5V Scan IC IC2802 VH IC5V Scan IC IC2803 VH IC5V Scan IC IC2804 VH IC5V Scan IC IC2805 VH IC5V Scan Signal Scan IC IC2806 IC5V 50 SCAN A ASSY (LOW SIDE) PDP-6071PU...
PSW_A REGULATOR IC3752 PQ120DNA1ZPH BUFFER +16.5V +12V POWER AMP IC WOW + VOLUME IC IC3751 IC3753 LA4625 NJW1183GK1 +12V BUFFER DC DETECT BLOCK A_Mute A_STBY_B R_Audio L_Audio MAIN Assy A_NG_B AUDIO ASS'Y R OUT L OUT SP TERMINAL ASSY PDP-6071PU...
CIMaX OOB_Data Logic Circuit [IC7302] I2C1 EBI BUS FLASH 32MBytes [IC6902] SPDIF out HSX_0 I2C0 SDRAM [IC6602] 256Mbit SDRAM BCM7038KPB1G-B2-K [IC6603] [IC6301] 256Mbit SDRAM [IC6604] 256Mbit SDRAM [IC6605] 256Mbit [12bit] Digital Video UARTA Gata ARRY [IC7201] From/To Main uCom PDP-6071PU...
Page 61
Audio L/R in Audio A/D [IC7101] From AV_SW ITU-R656 CVBS in VDEC [IC7001] I2C2 SDRAM [IC7002] 16Mbit Video out for monitor (Y, C) Audio L/R for monitor To AV_SW Audio L/R for PANEL (16bit) Digital Video out To Digital Selecter PDP-6071PU...
Page 65
V+3.3V_UCOM TEMP2_P TEMP2_P POD Assy MTB MAIN Assy CN9003(CKS3826-) (C3) CN4013(AKM1233- -TBB)(M10) Voltage Name Name PC_H PC_H PC_V PC_V PC_B 2.4* PC_B PC_G 2.4* PC_G PC_R 2.4* PC_R V+5V_A V+5V_A V+9V_A V+9V_A * When PC signal is not inputted. PDP-6071PU...
Page 66
LED_OFF LED_REC LED_REC MTB MAIN Assy LED_MDM LED_MDM CN4009(AKM1274- -TBB)(M4) Voltage LED- LED- Name Name 7.7/11 FAN_VCC FAN_NG1 TRAP-SW MTB MAIN Assy CN4018(AKM1213- -TFB)(M13) Voltage Name Name TRAP_SW V+3_3V_UCOM MTB MAIN Assy CN7101(AKM1276- -TBB)(M16) Voltage Name Name VBUS SHILD PDP-6071PU...
Page 67
AC state input TP3020 TXD_MD UART communication with MAIN u-com 0 to 3.3 TP3166 RXD_MD UART communication with MAIN u-com 0 to 3.3 TP3163 REQ_MD Communication demand to main system 0 to 3.3 TP3016 MODE Detection of MAIN Assy connection – PDP-6071PU...
Page 68
EXT_PD VSUS power supply adjustment signal TP3633 VSUS_ADJ Power supply PD signal TP3634 PS_PD Relay control TP3626 RELAY Large power supply ON/OFF control signal TP3616 DRF_B AC power supply state input TP3635 AC_DET Power down trigger signal TP3636 PD_TRG_B PDP-6071PU...
Page 69
– – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 70
– GND_LVDS – – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 71
– – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 72
– – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 73
– – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 74
– GND_LVDS – – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 75
– – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 76
– – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
Page 78
Function standby control signal TP3516 SCAN_PD SCAN_PD Y DRIVE PD signal input TP3509 YDD_PD YDD_PD Y DRIVE PD signlal input TP3510 YSUS_PD YSUS_PD Y DRIVE PD signlal input TP3511 Non-connection termial YDRV_PD YDRV_PD Y DRIVE PD signal input TP3512 PDP-6071PU...
Page 79
Power supply for VH Non-connection termial Non-connection termial Non-connection termial GNDH GNDH GND(PSUS) SI_H SI_H SI_H signal CLR signal OC2 signal OC1 signal CLK1 CLK1 CLK1 signal LE signal GNDH GNDH GND(PSUS) GNDH_R GNDH_R GND(PSUS). Connector detection IC5V IC5V IC5V power supply PDP-6071PU...
Page 80
P2: (B8B-EH) Pin No. Name Voltage [V] Name Pin No. Function +16_5V 16.5 +16_5V 16.5V power supply +6_5V +6_5V 6.5V power supply GND_D GND_D GND_SUS GND_SUS GND_SUS GND_SUS Non-connection termial VSUS VSUS VSUS power supply VSUS VSUS VSUS power supply PDP-6071PU...
: Checkered pattern of Black- White (MKSS13) signal : Checkered pattern of Black- White(MKSS13) : L1730(V+ADR1)(side-A through hole) : L1730(V+ADR1)(side-A through hole) V: 10V/div H: 2ms/div V: 10V/div H: 500ns/div • VADR ( 2 SF) • VADR ( 1 Field) PDP-6071PU...
Page 85
(60 X DRIVE Ass'y) H : 2ms/div ch2 K2912(ScanOUT) - K2301(SUSGND) (60 Y DRIVE Ass'y) V : 50V/div H : 5us/div (607 SCAN A Ass'y LOWSIDE) ch3 F2301(YPSUS) - K2301(SUSGND) V : 50V/div H : 5us/div (60 Y DRIVE Ass'y) PDP-6071PU...
Is there any local abnormality Is the abnormality associated Replace the panel chassis. with a single scan line? on the screen? with one address or one TCP? Failure analysis for the Failure analysis for the drive system ⇒ DR3 drive system ⇒ DR4 PDP-6071PU...
Page 87
Is an external video signal MAIN Assy ⇒ MA3 displayed properly? Problems concerning the audio output No Failure analysis for the Is the audio signal output? audio system ⇒ AU1 Specific failure whose cause is difficult to identify in the initial stage PDP-6071PU...
Replace the POWER SUPPLY 200 and 210 V (VSU: 125/35°C). specified range? Unit. The ripple must be within 10 V. Replace the POWER SUPPLY Is there a fluctuation in the VSUS voltage? Unit. The POWER SUPPLY Unit is normal. PDP-6071PU...
Replace the MAIN Assy. Replace the MAIN Assy. Is the indication position correct? It is most likely that the sync signal is abnormal. Is the tone correct? It is most likely that the video signal data are missing. Replace the MAIN Assy. PDP-6071PU...
Is the input signal normal? Replace the FFC cables. Replace the DIGITAL Assy. (See the oscilloscope photos.) Is the waveform of the control signal from the SCAN Assy Replace the Y DRIVE Assy. normal? (See the oscilloscope photos.) Replace the SCAN Assy. PDP-6071PU...
Page 91
Assy normal? Is the cable connected properly Connect the cable properly. Care must be taken that no dirt or dust is attached or gets in. to the 90-pin connector? (The SCAN IC may be damaged.) Replace the SCAN Assy. PDP-6071PU...
If the voltage at Pin 129 (RST3 port) on the main microcomputer is high, it is judged that the AC power Replace the MAIN Assy. cord is not plugged in, and operation of the unit will stop there. PDP-6071PU...
Is the selected input signal an ⇒ COMP / S2 analog TV signal? Is the selected input signal a ⇒ DTV digital TV signal? Is the selected input signal a ⇒ USB USB signal? No problem with the MAIN Assy PDP-6071PU...
Page 98
CN4005. If there is no ploblem, check the Flexible cable between CN4005 and CN8803. Check the communication between Is a signal output from jack? the CN8803 and Jack. If there was no ploblem replace IO Assy. Finishing troubleshooting. PDP-6071PU...
Page 100
Is a signal come to IC6301? IC6301and IC7101. If there is no problem, replace IC7101. Is a signal output from IC6301 and Check the communication between come to CN4007? (pin 3, 5) CN4007 and IC6301. If there is no problem, replace IC6301. PDP-6071PU...
Page 101
Home Menu? Media Gallery. Replace or reconnect flexible Check the Flexible cable between HNM Assy and CN4017. cable. Check the communication between Is a signal input to IC4701? CN4005 and IC4701and replace broken parts. Finishing troubleshooting. PDP-6071PU...
Page 102
Is the signal input from IC7201 to Check between IC7201 and IC8001? IC8001. Exchange IC6301 if there is no problem. Has the symptom been settled The panel is defective. when the MAIN Assy is replaced? Finishing troubleshooting. PDP-6071PU...
8 bits each. In a case of color difference 4:2:2, Y, Cb, and Cr use 12 bits each, but Cb and Cr are transmitted at a half sampling rate of Y. This unit is capable of processing the upper 10 bits out of 12 bits of video data. Recent high-end DVD players, such as Pioneer DV-79AVi, are capable of outputting 10-bit color- difference signals.
MAIN Assy Assy Assy 60 ADDRESS L 60 ADDRESS S 60 ADDRESS S 60 ADDRESS L Assy Assy Assy Assy TANSHI SP TERMINAL 60 IR Assy 42 & 60 LED Assy Assy Assy Front view Front view Rear view PDP-6071PU...
Side input Under cover (60) Tuner stay U POD stay A shield panel (U) shield 60 Y 60 X SIDE MAIN DRIVE DRIVE Terminal panel A TERMINAL Front chassis VL Assy 60 TANSHI 607 SCAN A 607 SCAN B PDP-6071PU...
Page 111
Remove the 22 screws. (APZ30P100FTB) Rear case (607) 1 1 1 1 1 1 Pull the lower part of the Front case Assy 607 Front case Assy 607 toward you and out. Remove the Front case Assy 607, by pulling it upward. PDP-6071PU...
Page 112
Remove the two handles. Rear case (607) ×3 ×3 Remove the 40 screws. (AMZ30P060FTB) ×11 Remove the six screws. (APZ40P100FTB) Remove the one screw. (ABA1341) Remove the rear case (607). Handle Sub frame cover L Sub frame cover R Handle PDP-6071PU...
Page 113
Disconnect cables, connectors, as required. POD Assy POD stay A Remove the POD cover. Remove the two hex. head screws. Remove the two screws. Remove the two screws. Remove the POD stay A with PCB. POD cover ×2 MAIN Assy PDP-6071PU...
Page 114
Remove the under cover (60). ×16 TANSHI Assy SP TERMINAL Assy Exchange of 607 SCAN A and B Assys Loosen the jumper wire. Remove the two screws. Remove the function button shield with PCB. Function button shield SIDE KEY Assy PDP-6071PU...
Page 115
607 SCAN A Assy 60 Y DRIVE Remove the 10 screws. Assy Disconnect the two pin connectors. Disconnect the 8 spacers. ×10 Remove the 607 SCAN A and B Assys. ×2 607 SCAN B Assy 607 SCAN A Assy Exchange PDP-6071PU...
Select “Channel Setup”. ( then ENTER) Select “POD ID”. ( • The Host ID and Cable Card ID appear. 5. Press HOME MENU to exit the menu. (*) : When replacing the MAIN Assy, be sure to do the FINAL SETUP. PDP-6071PU...
60 ADDRESS Assy No adjustment required No adjustment is required after replacement of parts SENSOR Assy other than those mentioned above. No adjustment required TANSHI Assy (*) : When replacing the MAIN Assy, be sure to do the FINAL SETUP. PDP-6071PU...
2 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 3 Issue the BCP command to transfer the data stored in the EEPROM for backup. 4 Turn the power off. PDP-6071PU...
Page 119
2 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 3 Issue the UAJ command to delete data stored in the EEPROM on the DIGITAL Assy. 4 Issue the BCP command to transfer the data stored in the EEPROM for backup. 5 Turn the power off. PDP-6071PU...
Page 120
When a DIGITAL Assy with an EEPROM in which adjustment data are stored is mounted, this step is not required after manual adjustment. ("DIGITAL EEPROM: REPAIR" is not indicated.) (2) Method using the RS-232C commands Issue the FAJ command. PDP-6071PU...
WBI S01 : Used to temporarily set the adjustment value of the Panel WB to default. (To return the value to its original value, use WBI S00.) PGM S00 : Used to set the gamma setting to Factory. Note: If the power is shut off in the process of the adjustment procedures, send the above commands again. PDP-6071PU...
Page 122
After the voltage adjustment is finished, make the following settings: Mask: OFF, Factory: OUT CA check Confirmation of setting data Check that the picture is properly displayed. Check that the each voltage is properly set. Use DVD, LD, and broadcast signals for checking. PDP-6071PU...
Page 123
10 minutes to raise the panel temperature to a certain extent. This ensures the accuracy of inspection and adjustment. (To 2 ) PDP-6071PU...
Page 124
Vofs_min2. Replace the panel Is Vofs_min2 144 (38 [V]) again or abnormality or smaller? in circuits Note: Return the Vofs value to the tentative This is for checking the lower limit of Vofs accurately. voltage setting. (To 3 ) PDP-6071PU...
Page 125
This is for checking the lower limit of Vofs accurately. voltage setting. Vofs_min Set the highest voltage among Vofs_min1, Vofs_ [STEP] min2 and Vofs_min3 as Vofs_min. Note: Take note of the lower limit color of Vofs (To 4 ) (pale purple or sky color or yellow egg color). PDP-6071PU...
Page 126
Vofs_max2. Replace the panel Is Vofs_max2 113 (32 [V]) again or abnormality or greater? in circuits Note: Return the Vofs value to the tentative This is for checking the lower limit of Vofs accurately. voltage setting. (To 5 ) PDP-6071PU...
Page 127
Value for Vofs = Vofs_max - 41 (8 [V]) 116 (23 [V]) or greater? Value for Vofs = Vofs_max - 61 (12 [V]) Set the Vofs as value for Vofs . (To 6 ) Vofs margin = Vofs_max - Vofs_min * Vofs= * Vofs Margin = determined PDP-6071PU...
Page 128
Turn the Mask off: Return to initial settings. Exit Factory mode: CA check Turn the unit off then back on again: POF, PON Use input signals from a DVD or PC for CA checking. Check that no bright cells or dark cells. PDP-6071PU...
Page 129
Conversion charts for electronic VRs (Vprst/Vofs) Vprst Setting value Vofs Setting value [STEP] [STEP] PDP-6071PU...
DIGITAL Assy XSUS-B SUS-G ADJUSTMENT 1 Measure the SUS-D input delay time (∆ Tsus-d). from DIGITAL Assy XSUS-D 2 Adjust the SUS-G input delay time so that it becomes "∆ Tsus-d + β ± 5 nsec." from DIGITAL Assy XSUS-G PDP-6071PU...
Page 131
DIGITAL Assy YSUS-B SUS-G ADJUSTMENT 1 Measure the SUS-D input delay time (∆ Tsus-d). from DIGITAL Assy YSUS-D 2 Adjust the SUS-G input delay time so that it becomes "∆ Tsus-d + β ± 5 nsec." from DIGITAL Assy YSUS-G PDP-6071PU...
Page 132
Assy Time SUS-G delay time: ∆ Tsus-g Adjust so that "∆ Tsus-g = ∆ Tsus-d + β ± 5 nsec," using the variable X DRIVE VR1001 120 nsec controls shown in the table below: Y DRIVE VR2011 100 nsec PDP-6071PU...
P COUNT INFO. < = > : NO OPRT P COUNT INFO. < = > : CLEAR Right SET (5 sec) MAX TEMP. < = > : NO OPRT Right MAX TEMP. < = > : CLEAR SET (5 sec) 3 Turn the power off. PDP-6071PU...
Location of the jumper connector 2. Remove the jumper connector from connector 1. As for service parts, the Jumper connector is P10 and connect it to connector P11. connected at connector P10. 3. Connect the cable connector from power SW to P10. PDP-6071PU...
How to come off Service Factory Mode. Case operated by remote control) • Service remote control : press [ FACTORY1 ] key. • Remote control : press [ HOME MENU ] key. Case to RS-232C transmit command) • Send [FAN] . PDP-6071PU...
(screenize switching, etc). • Data on screen (i.e.,screen position; meaning clock dividers, and not including data on screen size) Are reset to the default values (data stored in memory will be retained). Screen size will be retained. PDP-6071PU...
: When ten seconds have passed since the [ DRIVE ON/OFF ] key was pressed at the standby, it becomes invalid. Please press [ POWER ] key from the [ DRIVE ON/OFF ] key pressing within ten seconds when you do power supply ON while driven OFF. Remote Control Unit for Servicing PDP-6071PU...
INTR-POS1(0x75) ⇔ 8.2.4.8 HDMI INTR POSITION (+) 000 to 255 for technical analysis INTR-POS2(0x76) ⇔ 000 to 255 for technical analysis INTR-POS3(0x77) ⇔ for technical analysis 000 to 255 INTR-POS4(0x78) ⇔ 000 to 255 for technical analysis PDP-6071PU...
Note: See SIG-Mode Tables.(See next page.) Color system and Signal type Color system and signal type NTSC Composite input S-connector input Y/CB/CR Y/PB/PR Digital video signal Option(Destination, Panel Generation, etc) Options SX System in North America(Regular) ATB7 SX system in North America(ELITE) AHB7 PDP-6071PU...
Page 140
46.875 1024x768 60.004 48.363 70.069 56.476 75.029 60.023 1360x768 60.015 47.712 Selection of the screen size by the user is displayed. GUI Notation VIDEO Remark Character DOT BY DOT FULL (FULL1) ZOOM CINEMA WIDE FULL2 : supported, : unsupported PDP-6071PU...
In the 29-32 rows, ROM version information on each device is displayed. In the 19-24 rows, Version information on a common treatment is displayed. At the position "14x35", The Past/Highly effective panel distinction information is displayed. " P " : The past panel, "F" : The highly effective panel PDP-6071PU...
Page 142
CFE Version HHHHHHHH KERNEL Version KERNEL HHHHHHHH ROOTFS Version ROOTFS HHHHHHHH FLAGS FLAGS (Y) FONTS(Y) DFTS (Y) PLOG (Y) 8.2.1.3 VERSION(3) Flash Device Item Name Elite Regular CCD-UCOM Version MSKB HMG/HG module Version HMG/HG 0123456789 User Password PASSWORD 1234 PDP-6071PU...
Page 143
- TV-Guide Error HOME-G - Failure at Home Gallary MA-PWR M-DCDC -Abnormally in RST2 of MAIN Assy (power decrease of DC-DC converter) RELAY -Abnormally in RST4 of MAIN Assy (power decrease of Relay power) Failure at Home Media Gallary START PDP-6071PU...
Page 144
Even if [ ← ] key or [ → ] key is pushed, "CLEAR ⇔ YES" ⇔ "CLEAR ⇔ NO" is repeated. If the [ ENTER ] key is kept on pressing for 5 second when the status of this menu is <YES>, clear process will begin. PDP-6071PU...
In HOUR METER screen on Factory Menu, press the [ENTER] key, and then it moves to the screen to clear MTB HOUR METER. Display/Meaning: Meaning Item Name RS-232C command HOUR METER(PANEL) PANEL 00151H 21M HOUR METER(MTB) 00151H 21M – POWER ON COUNTER P-COUNT 00000095 TIMES SYSTEM SERIAL SERIAL PDP-6071PU...
Page 146
Video information: valid horizontal pixel numbers (low order bit) - 3B: Video information: valid horizontal pixel numbers (high order bit) - 3C: Video information: valid vertical line numbers (low order bit) - 3D: Video information: valid vertical line numbers (high order bit) PDP-6071PU...
Page 147
H RES V RES H DE V DE V FMT 480i (525i) 262 or 263 720x480i @ 60 480p (525p) 720x480p @ 60 1080i (1125i) 2200 562 or 563 1920 1920x1080i @ 60 720p (750p) 1650 1280 1280x720p @ 60 PDP-6071PU...
Page 148
Displays input signal status of MVDEC terminal. Device Context MVDEC Signal distinct result 1 Signal distinct result 2 Flag detection output Noise level distinction 1 Noise level distinction 2 Non-standard signal detection Sub carrier signal detection ACC data output ACC information output Input signal mode PDP-6071PU...
Page 149
Displays digital broadcast signal information and status upon receiving digital signal. 8.2.1.13 DTV TV-GUIDE BER Exclusively used for production line. TV-Guide error bit ratio information is displayed. 8.2.1.14 DEBUG INFO Exclusively used for technical analsyis. Debug information for development use is displayed. PDP-6071PU...
8.2.2.9 RASTER MASK SETUP (+) The mask indication (RASTER) can be set and indicated. 8.2.2.10 PATTEN MASK SETUP (+) The mask indication (PATTERN) can be set and indicated. 8.2.2.11 COMBI MASK SETUP (+) The mask indication (COMBI) can be set and indicated. PDP-6071PU...
• P-COUNT: The accumulated power-on count is indicated. • TEMP1: The current panel temperature and the historical maximum temperature recorded in memory are indicated. The range of temperature indication is from -50.0 to +99.9. (The temperature unit is " °C (Centigrade) ".) PDP-6071PU...
Page 152
Drive Sequence Processing IC SQ-IC Drive Sequence Stop SQNO Communication Busy BUSY Version Mismatching VER-HS MAIN EEPROM Communication Error EEPROM MDU-IIC MD-IIC BACKUP EEPROM Communication Error BACKUP DAC Communication Error High temperature of the panel TMP-NG Temperature NG TEMP PDP-6071PU...
Page 153
: Subtracting by one from the adjustment/setting value <VOL+> : Adding by 10 to the adjustment/ setting value <VOL-> : Subtracting by 10 from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
Page 154
: Subtracting by one from the adjustment/setting value <VOL+> : Adding by 10 to the adjustment/ setting value <VOL-> : Subtracting by 10 from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
Page 155
<DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
Page 156
<DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
Page 157
Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. • 48 V and 60 P are deleted from the sequence, and represented by 50 V and 60 V, respectively. The ABL/WB table is changed to the PC table. PDP-6071PU...
Page 158
Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. • 48 V and 60 P are deleted from the sequence, and represented by 50 V and 60 V, respectively. The ABL/WB table is changed to the PC table. PDP-6071PU...
Page 159
Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. • 48 V and 60 P are deleted from the sequence, and represented by 50 V and 60 V, respectively. The ABL/WB table is changed to the PC table. PDP-6071PU...
If the signal is changed to cable, then the cable’s broadcast map is configured, and air’s broadcast map is destroyed. OSD display Funcrion Control device CABLE Change the antenna setting to cable Change the antenna setting to air 8.2.3.3 AFT Exclusively used for production line. PDP-6071PU...
DIG MVDEC YCBCR MAIN VDEC: YCbCr (Digital output mode) ANA MVDEC YCBCR MAIN VDEC: YCbCr (Analog output mode) ANA MVDEC Y MAIN VDEC: Y (Analog output mode: SG VDEC return setting) ANA AD YCBCR AD: YCbCr ANA AD RGB AD: RGB PDP-6071PU...
Page 162
For this account the latter part from MVDEC does not have set values, resulting in having funny colors in colorbar, the brightness changes after switching, etc. This is not a damage result nor error. • Depending on MVDEC’s part version, ANA_MVDEC_YCBCR may not display colors. PDP-6071PU...
Page 163
When the configuration is set to <YES> and the [SET] key is pressed for 5 seconds, the reset action executes. Be sure to disconnect and connect the Power cord after the FINAL SETUP. When replacing the MAIN ASSY, the FINAL SETUP is required. PDP-6071PU...
Page 164
For ELITE model Be sure to do above procedure at input fuction except HMG. 2nd FACTORY MODE [ Home Gallery ] (Regular Model) 1. Home Gallery Screen (1) When the device is connected (2) When the device is not connected PDP-6071PU...
Page 165
0 E (Endpoint descriptor info) - E (Endpoint descriptor info) Endpoint Address (I=In, O=Out) Hexadecimal(String) Attributes Hexadecimal(String) MxPS Endpoint Max Packet Size Decimal Interval (max) between transfers Decimal 2. End method It is the same as the case that Home Gallery displays. PDP-6071PU...
During standby mode, press the [Home Menu] key, and then press the [POWER] key within 3 seconds. Or during Factory mode, hold the [INTEGRATOR] key. #In INTEGRATOR MENU, there is a OSD where SR+(or RS-232C) is turned on/off, and it switches on the screen. PDP-6071PU...
ETX, the character string sandwiched between STX and ETX is recognized as a command. If the prepared character string storage buffer (24 bytes including STX, ID and ETX) is exceeded, a reply will not be sent out. PDP-6071PU...
The data length will be subject to each individual specification as the content of a reply will be different depending on the type of QUEST command. Data transmitted from PC Reply data Command Command Parameter ∗∗ 0x02 0x03 0x02 • • • • • • • • • 0x03 PDP-6071PU...
Factory mode on ¶ Set each memory setting of MTB side to the shipment state. MDU MTB ∗∗∗ ¶ User white balance : GREEN highlight ∗∗∗ ¶ User white balance : GREEN lowlight ¶ ¶ Green side mask level adjustment PDP-6071PU...
Page 171
¶ RASTER17: Pale purple ¶ ¶ RASTER18: Magenta 53 ¶ ¶ RASTER19: Red 1023+ ¶ ¶ RASTER20: Green 1023+ ¶ ¶ RASTER21: Blue 1023+ ¶ ¶ RASTER22: Red 588+ ¶ ¶ RASTER23: Green 588+ ¶ ¶ RASTER24: Blue 588+ PDP-6071PU...
Page 172
¶ Acquiring data on the status of the unit, such as temperature Acquiring unit data, such as the software version common ¶ to all models, regardless of destination ¶ Acquiring data on shutdown PDP-6071PU...
Page 173
Setting the screen size to WIDE – – MDU MTB ¶ Determining the flag for the DIGITAL Assy adjustment in "not adjusted" To add ∗∗∗ to the adjustment value (∗∗∗ = 000 to 999, ¶ UP∗ designated by a function command) PDP-6071PU...
Page 174
Y-SUS-B ADJ ∗∗∗ ¶ ¶ Y-SUSTAIL T2 ADJ ¶ ∗∗∗ ¶ Y-SUSTAIL T1 ADJ ¶ ∗∗∗ ¶ Y-SUSTAIL W ADJ ¶ ¶ Initializing the video EEPROM data ¶ ¶ Initializing the setting data to which no adjustment command is provided PDP-6071PU...
TXC / Re gula r (US) J Japan (reserved) S System model B Not used.( For Future) B All-in-one design TV Regular D Panal Type Regular A M Monitor P the past D Standard module F High-effective E Simple module PDP-6071PU...
Adjustment not completed 11: Operation status 13: MASK indication X-DRV induced by SD X-DCDC MASK-OFF Normal X-SUS MASK-ON 3: Adjustment-data Relay-off completed backup Not used During warning Not used With backup data indication Not used No data (default) UNKNOWN PDP-6071PU...
RYW adjustment value 3 Byte R-REVICE setting value 1 Byte G-REVICE setting value 1 Byte B-REVICE setting value 1 Byte 2 Byte • For each REVICE setting value, the level set for RRL, RGL, or RBL is transmitted as one character. PDP-6071PU...
To acquire data on operations of the panel Return data: 3 (ECO)+40(DATA)+2(CS)= 45 Byte Data Data Arrangement Output Example Length 3Byte Pulse meter B 1 8Byte 00000000 Pulse meter B 2 8Byte 00000000 Pulse meter B 3 8Byte 00000000 Pulse meter B 4 8Byte 00000000 Pulse meter B 5 8Byte 00000000 2Byte PDP-6071PU...
Data from the hour meter for the seventh latest PD 8 Byte 00000213 Eighth latest "1st PD" data 1 Byte Eighth latest "2nd PD" data 1 Byte Data from the hour meter for the eighth latest PD 8 Byte 000001A7 2 Byte PDP-6071PU...
Data from the hour meter for the seventh latest SD 8byte 00000000 BACKUP Eighth latest SD data 1byte Eighth latest SD subcategory data 1byte Data from the hour meter for the eighth latest SD 8byte 00000000 ¶ SD subcategory (TEMP) 2Byte No SD-Sub data TEMP1 Reserved PDP-6071PU...
1 byte FLAGS Information 3 1 byte FLAGS Information 4 1 byte FLAGS Information 5 1 byte FLAGS Information 6 1 byte Version of CCD-UCOM 4 byte HMG/HG MODELE Version 10byte User Password 4 byte Check Sum 2 byte PDP-6071PU...
1 Byte Result of detection of cracking in the panel 1 Byte Result of detection for scanning protection 1 Byte Result of detection for external protection 1 Byte Transition of protection operation 1 Byte ∗∗∗∗ Reserved 4 Byte 2 Byte PDP-6071PU...
<No.1 Subcategory Information on "failure in 3-wire serial communication of Main microcomputer"> Data Cause of shutdown Remarks Non subcategory IF microcomputer communication failure IF (immediately Power Supply OFF) MANTA communication failure (MULTI1) MULTI1 (immediately Power Supply OFF) MANTA communication failure (I/P) MANTA communication failure (D-SEL) D-SEL PDP-6071PU...
9.3.13 DRV 7 DRV Drive ON/OFF : ON/OFF control for only the large-power system Remarks Effective Condition Function Format [DRV+S00] Every time DRIVE OFF At standby mode, when 10 seconds passed after issuing [DRV+S00], command becomes invalid. [DRV+S01] DRIVE ON PDP-6071PU...
• While ZACS01 is established, the LED for ZAC flashes. The priority of LED indications is as follows: PD > Trap-SW > DTV_STB > SD > ZAC >DTN > no backup copy > Standalone operation of the Assy > Normal ON/OFF • Even if DTNS00 is established, if ZACS01 is established, DTV/HomeNet communication must be prohibited. PDP-6071PU...
To make the flag setting that [CBU] Writing F0 to the 2 k byte ROM The backup ROM is indicating that backup data initialized. have not been copied To copy Digital backup data [BCP] Copying backup data to EEPROM PDP-6071PU...
4 : The MOD microcomputer controls the relay of the power MOD of the PDP to startup the power of the PDP. 5 : The main microcomputer controls the ASIC power within the MTB to startup the power of the MTB. PDP-6071PU...
Command [DRVS00/S01] is effective even during standby. When the main power is turned OFF, however, [DRVS01] (release) will be effective. Short the two adjacent electrodes on the surface by a method which assures continuity, such as using a crocodile clip. 60 DIGITAL Assy PDP-6071PU...
Fan Operation According to the reading value of above table sensor. HIGH or LO FAN_CONT: "L" [ Outline Circuit ] FAN_vcc Vref = 2.64V H : Vo = 11V L : Vo = 7.6V U-COM FAN_CONT H: On L: Off PDP-6071PU...
Specifications for port monitoring Port Name SD/PD Indication Assigned Pin Active FAN_NG 1 Shutdown with H Abnormally high Shutdown when the TEMP2 temperature in the value exceeds the predetermined value TRAP_SW Circuit diagram TRAP_SW MTB MAIN Assy V_3.3V_UCOM TRAP_SW MAIN_UCOM PULL_D PDP-6071PU...
TRAP SW on ahead, carry out following procedure from this state. Cancelling by the remote control • Enter to the Factory mode. • Then, proceed to INITIALIZE layer inside the Factory mode, and then press "DISPLAY" key for more than 5 seconds. PDP-6071PU...
HDCP (High-bandwidth Digital Content Protection) is a technology used to protect copyrighted digital contents that use the Digital Visual Interface (DVI). ** This conforms to USB 1.1 and 2.0 . Design and specifications are subject to change without notice. PDP-6071PU...
(for PDP-6071HD only) Terminal position sheet (for use when mounting the Plasma Display on the wall) (AAX3330) Buttons used for only basic operations are provided on the simplified remote control unit. You can use it as necessary. PDP-6071PU...
For details, refer to the operation manual that 7 INPUT button (ENTER button*) came with the stand or speaker. 8 VOLUME UP/DOWN buttons (UP/DOWN buttons*) The buttons with asterisks (*) can operate the TV Guide On Screen™ system. 9 CHANNEL UP/DOWN buttons (LEFT/ RIGHT buttons*) PDP-6071PU...
Page 199
PDK-TS15U for the PDP-6071HD/ 13 INPUT 3 terminals (AUDIO) PDP-6070HD 14 INPUT 3 terminals (COMPONENT VIDEO: Y, 28 Speaker: PDP-S41 For details, refer to the operation manual that 15 INPUT 2 terminals (COMPONENT VIDEO: Y, came with the stand or speaker. PDP-6071PU...
All buttons on the main remote control unit are luminous and gather and store light. This enables quick access to the desired function when performing operations in dark places. NOTE When using the remote control unit, point it at the Plasma Display. PDP-6071PU...
Page 202
All output reset CLR terminal : L → normal operation, CLR terminal : H→ All output "H" − 93 - 94 GND1 − N.C. Not used − 96 - 97 Power for High-voltage circuit − N.C. Not used 99 - 100 OUT1 - OUT2 High-voltage push-pull output PDP-6071PU...
Page 203
USB 2.0 Digital Dual Audio 2x I S Ports Channel USB 1.1 1x SPDIF Audio Processor Analog Ethernet Audio 2x Dual Audio DDR-DRAM Controller DACs EJTAG Peripherals (200 MHz) Dual SATA S-ATA 64-bit wide DDR DRAM Test IR/LED/Key/UART SPI/BSC/GPIO/PWM SmartCard PDP-6071PU...
Page 204
R5520H001B (MAIN ASSY : IC7105) • USB HIGH-SIDE SW IC BLOCK DIAGRAM GATE CURRENT CONTROL LIMIT FLAG DELAY UVLO THERMAL SHUTDOWN PIN LAYOUT PIN FUNCTION Function Pin No. Name Enable terminal GND terminal FLAG terminal (Open-drain output) Power input terminal Output terminal PDP-6071PU...
Page 209
Digital 3.3V power supply Connect to the 3.3V power supply. 109,120,132 DGND 17,24,33,38,45,56, – – Digital ground – 80,89,93,104,114, 2.2 System reset terminal Acronyms Terminal number Level Buffer type Functions PU/PD [kΩ] RSTB Schmitt – System reset input (Active-Low) PDP-6071PU...
Page 210
Connect to GND normally. VLPF1 Analog – Analog test output Connect to GND via a 0.1µF capacitor. VLPF2 Analog – Analog test output Connect to GND via a 0.1µF capacitor. Caution: Connect these terminals for test to GND unless otherwise instructed. PDP-6071PU...
Page 211
Digital RGB/B signal input DCRI LVTTL – Digital RGB/R signal input FCSI LVTTL 3 mA Sync separation signal input/timing output (HD) for RGB input. 3-state It will become Hi-Z when FCSIS[2:0] (SA22h, D2-D0)=000b. Normally, set to FCSIS[2:0]=0 and leave it open. PDP-6071PU...
Page 212
ADC2 top reference voltage Connect to GND via a 0.1µF capacitor. VRB2 Analog – ADC2 bottom reference voltage Connect to GND via a 0.1µF capacitor. VCOM2 Analog – ADC2 in-phase reference voltage Connect to GND via a 0.1µF capacitor. PDP-6071PU...
Page 213
Color difference component Cb/RGB component B output signal. Connect to AGNDA via a 200Ω load resistance. Analog – External reference input pin. Supply 1.0V. And, connect to AGNDA via a 0.1µF capacitor. RSET Analog – Connect to AGNDA via a 620Ω resistor for external adjustment. PDP-6071PU...
Page 214
3 mA Horizontal sync signal output 3-state LVTTL 3 mA Vertical sync signal output 3-state VBLK LVTTL 3 mA V blanking output 3-state FILD LVTTL 3 mA Field output 3-state RDEO LVTTL 3 mA Effective pixel range output 3-state PDP-6071PU...
Page 215
3 mA Address output for external memory -SDRA11 3-state Insert a damping resistor of approximately 100Ω, 13,12,10,9,8, and connect to the SDRAM address terminal. 7,6,5 SDRDQ0 51,49,46,42, LVTTL 6 mA Data input/output for external memory. 3-state -SDRDQ15 40,36,34,30, 31,35,37,41, 43,47,50,52 PDP-6071PU...
Page 216
(Not to Scale) BLUE <7> SOGIN BLUE <6> BLUE <5> BLUE <4> BLUE <3> BLUE <2> BLUE <1> BLUE <0> 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 PDP-6071PU...
Page 217
1, 10, 20, 21, 24, 25, 28, 32, 36, 40, 41, 44, 47, 50, 53, 60, 61, 63, 68, 80 Control Serial Port Data I/O 3.3 V CMOS Serial Port Data Clock (100 kHz Maximum) 3.3 V CMOS Serial Port Address Input 1 3.3 V CMOS PDP-6071PU...
Page 218
Hsync is active; the trailing edge is ignored. When Hsync Polarity = 0, the falling edge of Hsync is used. When Hsync Polarity = 1, the rising edge is active. The input includes a Schmitt trigger for noise immunity, with a nominal input threshold of 1.5 V. VSYNC Vertical Sync Input The input for vertical sync. PDP-6071PU...
Page 219
The designer should provide quiet, noise-free power to these pins. Ground The ground return for all circuitry on-chip. It is recommended that the AD9985 be assembled on a single solid ground plane, with careful attention given to ground current paths. PDP-6071PU...
Page 220
Control Signals EVNODD Video Color HS,VS, HSYNC Space Converter VSYNC R0XC ± PanelLink 24-Bit Up/Down ODCK Data TMDS Sampling R0X0 ± Q[23:0] Digital R0X1 ± CLK48B Core R0X2 ± Auto A/V Port Exception MUTEOUT Handling Detect SCDT R0PWR5V R1PWR5V PDP-6071PU...
Page 222
Output LVTTL Output LVTTL Output LVTTL Output LVTTL Output LVTTL Output LVTTL Output Data enable. HSYNC LVTTL Output Horizontal Sync Output control signal. VSYNC LVTTL Output Vertical Sync Output control signal. ODCK 12 mA LVTTL Output Output Data Clock. PDP-6071PU...
Page 223
2. CLK48B is used to clock external 24-to-48 bit latches. CLK48B is also latched on the rising edge of RESET# to set the I2C device addresses for CSCL/CSDA. Refer to Table 10. CLK48B has a weak internal pull-down, and so will be latched as a LOW if not otherwise connected. PDP-6071PU...
Page 224
PVCC1 Power TMDS Port 1 PLL VCC 3.3V TMDSPGND Ground TMDS PLL GND AUDPVCC18 Power ACR PLL VCC 1.8V AUDPGND Ground ACR PLL GND XTALVCC Power ACR PLL Crystal Input VCC 3.3V REGVCC Power ACR PLL Regulator VCC 3.3V PDP-6071PU...