Related Manuals for LG PQRCHCA0Q
Summary of Contents for LG PQRCHCA0Q
- Page 1 OWNER’S & INSTALLATION MANUAL SIMPLE WIRED REMOTE CONTROLLER Please read this manual carefully before operating your set and retain it for future reference. MODELS : PQRCHCA0Q PQRCHCA0QW www.lg.com P/NO : MFL62862003...
- Page 2 TIPS FOR SAVING ENERGY TIPS FOR SAVING ENERGY Here are some tips that will help you minimize the power consumption when you use the air conditioner. You can use your air conditioner more efficiently by referring to the instructions below: •...
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE. Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product WARNING It can result in serious injury or death when the directions are ignored CAUTION It can result in minor injury or product damage when the directions are ignored WARNING... - Page 4 IMPORTANT SAFETY INSTRUCTIONS CAUTION • Do not clean using the powerful detergent like solvent but use soft cloths. - It will cause fire or product deformation. • Do not press the screen using powerful pressure or select two buttons. - It will cause product breakdown or malfunction. •...
-
Page 5: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS TIPS FOR SAVING OWNER'S INSTRUC- ENERGY TION Standard Operation IMPORTANT SAFETY IN- - Cooling Mode STRUCTIONS - Heating Mode - Auto Operation Mode PART DESCRIPTION - Dehumidification Mode Using the remote control - Fan Mode Accessory Function setting - Fan Speed Selection... -
Page 6: Part Description
PART DESCRIPTION PART DESCRIPTION Using the remote control Display screen Control button SPEED TEMP ROOM TEMP Control Display screen Description panel T T emperature adjustment button: Adjusts the room temperature when 18~30°C cooling and heating. Indoor fan speed button: Adjusts the fan speed. On/Off button: Turns the power on/off. -
Page 7: Installation Instruction
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Please fix tightly using provided screw Please check if connector after placing remote controller setup board is normally connected. on the place where you like to setup. - Please set it up not to bend because poor SPEED TEMP ROOM... -
Page 8: Group Control
INSTALLATION INSTRUCTION Group Control - For wall-mount type and stand type prod- uct, change the master/slave setting with the wireless remote controller. (Refer to wireless remote controller manual for de- tail) ❈ When installing 2 remote controllers to Signal wire one indoor unit with event communica- tion function, set the master/slave of the remote controller. -
Page 9: Install Setting
INSTALLATION INSTRUCTION Install Setting If you want to set installer setting mode, Press the Temperature up button and the How to enter installer setting mode Room Temp button same time for five sec- onds. CAUTION When you enter the setting mode Initially. Function code is displayed on the LCD •... -
Page 10: Installer Setting Code Table
INSTALLATION INSTRUCTION <Installer Setting Code Table> General air-conditioner product Function Code Value Test Run 01:Set Address Setting 00~FF : Address <ESP Step> <ESP Value> <Example> 01:VeryLow 0 ~ 255 02:Low E.S.P. Value 03:Med Function Code ESP step ESP value 04:High 05:Very High 01:Remo Thermistor... -
Page 11: Test Run Mode
INSTALLATION INSTRUCTION Test Run Mode Setting Address of Central control After installing the product, you must a test It’s the functional to use connecting central Run Mode. For details related to the Product control. manual. Press button and button Simulta- Press button and button Simulta-... -
Page 12: E.s.p
INSTALLATION INSTRUCTION E.S.P Thermistor This is the functional that decides the strenth This is the function to select the temprature of the wind for each wind level and because sensor to judge the room temperature. this function is to make the installation easier. - If you set ESP incorrectly, the air conditional Press button and... -
Page 13: Ceiling Height Selection
INSTALLATION INSTRUCTION Ceiling Height Selection Static Pressure Setting This function is to adjust FAN Airflow rate ac- This function is applied to only duct type. Set- cording to ceiling height (For ceiling type prod- ting this in cases will cause malfunction. uct) Press button and... -
Page 14: Remote Controller Master/Slave Setting
INSTALLATION INSTRUCTION Remote Controller Master/Slave Fahrenheit Switching Setting This function is used for switching the display between Celsius and Fahrenheit. It’s a function for setting in group control, or 2- (Optimized only for U.S.A) remote controller control. Press button and button Simulta- Press button and... -
Page 15: Owner's Instruction
OWNER'S INSTRUCTION OWNER'S INSTRUCTION Standard Operation Press the button. ❈ The operation mode can be set from Cen- tral Controller only. Cooling Mode It cools the room by comfortable and Clean wind. When the room temperature is lower than the desired temperature Press the button. -
Page 16: Function Setting
OWNER'S INSTRUCTION Function setting Room Temperature Check Fan Speed Selection 1 Press the button. You can easily control the fan speed. 1 Press the button. 2 Press the button. Fan Speed Selection in Cooling Operation NOTE • “To change the temperature display to Celsius or Fahrenheit, change LCD dis- play by referring to page 14.”...