Page 1
Wide Wired Remote Controller Owner's & Installation Manual Models:PQRCUSA0 IMPORTANT • Please read this owner's & installation manual completely before installing the product. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only.
Wide Wired Remote Controller Owner’s & Installation Manual Safety Precaution Safety Precaution TABLE OF CONTENTS • The installation requires expert skills, and it should be installed by the service center or other shops specialized in the installation and recognized by our company. I Safety Precaution .....................3~4 I Part Description ....................5 •...
Safety Precaution Part Description Part Description Request to the service center or installation Do not give the shock using sharp and specialty store when the product becomes wet. pointed objects. • It will cause fire or electric shock. • It will cause breakdown by damaging parts. Name and Function of Remote Controller OPERATION INDICATION SCREEN...
Installation instruction Installation instruction 4. After fixing the top part of the Installation instruction remote controller to the installation board as shown in beside picture, press the bottom part to assemble 1. Connect the remote controller Wall Wall the controller to it’s board. cable to the wired remote Side Side...
Installation instruction Installation instruction Group control Installer Setting -How to enter installer setting mode 1. When installing more than 2 CAUTION units of air conditioner to one Installer setting mode is to set the detail function of the remote controller. wired remote controller, please If the installer setting mode is not set correctly, it can cause problems to the product, user injury or connect as the right figure.
Installation instruction Installation instruction <Installer Setting Code Table> Installer Setting -Test Run Mode Function Code Value After installing the product, you must run a Test Run mode. Test Run 01:Set For details related to this operation, refer to the product manual. Address Setting 00~FF : Address <ESP Step>...
Installation instruction Installation instruction Installer Setting - Setting Address of Central Control Installer Setting -E.S.P. What is an E.S.P function? This is the function that decides the strength of the wind for each wind level and because this Press the button for 4 function is to make the installation easier, please do not use this function when using the remote seconds to enter the installer...
Installation instruction Installation instruction Installer Setting -Thermistor Press button to save or release. Press button for 4 seconds to enter the installer setting mode until timer segment display “01:01”. Press button to exit or the system will automatically exit after 25 seconds Repeat pressing button to select without any input.
Installation instruction Installation instruction Installer Setting -Ceiling Height Selection Installer Setting -Static Pressure Setting This function is to adjust FAN Airflow rate according to ceilingheight (only cassette model) This function is applied to only duct type. Setting this in other cases will cause malfunction. Press button for 4 seconds to enter the installer setting...
Installation instruction Installation instruction Installer Setting-Group Setting Installer Setting -Mode Override Setting This function is only for group control operation. Please don’t set this function in case of non-group In case of More than 2 indoor units connected to 1 outdoor unit, they are assigned as Master indoor control.
Installation instruction Installation instruction Installer Setting-Dry Contact Mode Setting Installer Setting-Zone State Setting This function allows the Dry contact-indoor unit operate under Auto Run mode or Manual mode with This function is only available on some products. remote controller. It is possible to setup Variable or Fixed option for Zone State of indoor. The initial setting is 'Variable' Press button for 4 seconds Press...
Installation instruction Installation instruction Installer Setting-Celsius / Fahrenheit Switching Installer Setting-Zone Type Setting This function is used for switching the display between Celsius and Fahrenheit. This function is only available on some products. (Optimized only for U.S.A) It is possible to setup zone new type or old one of the product which is available to install the damper controller.
Installation instruction Installation instruction Installer Setting-Zone Number Setting Installer Setting -Optional Function Setting This function is only available on some products. For the optional product such as PLASMA PURIFICATION/DEHUMIDIFIER/ ELECTRIC HEATER and VENTILATION, ELEVATION GRILL. Zone Number is to set the number of installed zones. It's possible to control only in zone new type It is possible to set the items are installed or not Press button for 4 seconds...
Owner's instruction Owner's instruction Cooling Mode - Power Cooling Owner's instruction It makes the room cool using pleasant and fresh air quickly Cooling Mode - Standard Operation Press button to turn on the Press button to turn on the indoor. indoor.
Owner's instruction Owner's instruction Dehumidification Mode Auto Operation Mode Press button to turn on the Press button to turn on the indoor. indoor. Press button to select Auto Press button to select Operation Mode. Dehumidification mode. The temperature setting can not be adjusted during operation Incase of operating under this mode.
Owner's instruction Owner's instruction Fan Mode Temperature setting/ room temperature check Press button to turn on the We can simply adjust the desired indoor. temperature. • Press the buttons to adjust the desired temperature. Press button. : Increase 1˚C or 2˚F per one time pressing : Decrease 1˚C or 2˚F per one time pressing...
Owner's instruction Owner's instruction Ariflow Setting Sub function : Plasma Purification We can simply adjust the desired airflow rate Repeat pressing button until icon flash. Press buttons to set the desired airflow direction. ¡ (NONE) ¡ ¡ ¡ Operate or cancel Plasma •...
Owner's instruction Owner's instruction Sub function : Electric Heater Sub function : Fan Auto Repeat pressing button Repeat pressing button until the icon flash. until icon flash. Operate or cancel Fan Auto Turn on/off ELECTRIC HEATER function by pressing button. by pressing button (the icon appears/disappears...
Owner's instruction Owner's instruction Function setting : Child Lock Function setting : Elevation Grill This function is to prevent children or other This function is to move the indoor filter people from using indoor. up/ down for cleaning filter. The setting is applied only to product that has this function.
Owner's instruction Owner's instruction Function setting : Vane Angle Control Press button to complete and active the setting process. (Airflow direction This function is to adjust angle at which airflow is blow out. function will be released whenever setting vane angle) Press button.
Owner's instruction Owner's instruction Function setting : Zone Control Changing Current Time To turn on/off the zones by used of it Keep pressing button for 4 secs to enter Setting current time mode. Press button. Ex) Changing Current Time as 'Monday / AM 10:20'.
Owner's instruction Owner's instruction Programming : Setting Simple Reservation In case of there is not any reservation setup on system, it is possible to make a SIMPLE reservation Press button to move to 'Minute' on indoor unit. setting mode. (the 'Minute' segment will flash) Press button to enter the...
Owner's instruction Owner's instruction Programming : Setting Sleep Reservation Programming : Setting ON Reservation This function is able to turn off Air conditioner when sleeping or after some hours. This function is able to turn air conditioner ON after a setting time. Press button.
Owner's instruction Owner's instruction Programming : Setting OFF Reservation Programming : Weekly Reservation This function is able to turn air conditioner OFF after a setting time. The weekly reservation is active after setting current time Press button. Press programming button to enter the Programming mode.
Owner's instruction Owner's instruction Programming : Holiday Reservation Press up, down button to adjust the Minute on Start Time section. This function is to automatically stop the machine working on some days. Press button to enter the reservation setting mode. Press right button to move to 'Hour' Repeat pressing button to...
Owner's instruction Owner's instruction Ventilation Kit Control Error code display function If there is a linkage between ventilator and air conditioner, it is able to control this ventilator. When the error occurred in the indoor unit, then the error code will be displayed on remote controller When the error occurred in the indoor unit, then the error code will be displayed on remote controller - "CH"...
Page 27
P/No.: 3828A20860K Printed in Korea After reading this manual, keep it in a place easily accessible to the user for future reference.