Electrolux W555H Installation Manual
Washer extractor
Hide thumbs
Also See for W555H:
- Service manual (74 pages) ,
- Operating manual (24 pages) ,
- Specifications (2 pages)
Related Manuals for Electrolux W555H
Summary of Contents for Electrolux W555H
- Page 1 Installation manual Washer extractor W555H Type W.55.H 438 9054-30/EN Original instructions 2017.05.03...
-
Page 3: Table Of Contents
Contents Contents 1 Safety Precautions ..........................5 General safety information......................6 Commercial use only........................6 Symbols............................6 2 Technical data.............................7 Drawing ............................7 Technical data ...........................8 Connections ..........................8 3 Setup ..............................8 Unpacking ..........................8 Siting ............................9 Mechanical installation ......................10 4 Marine installation ..........................11 5 Water connection ..........................12 6 Connection of external dosing systems ....................13 Connection of the hoses ......................13 Electrical connection of external dosing system................13... -
Page 5: Safety Precautions
Installation manual 1 Safety Precautions Only use detergent intended for water-wash of textiles. Never use dry cleaning agents. The machine's door lock must under no circumstances be bypassed. If the machine develops a fault, this must be reported to the person in charge as soon as possible. -
Page 6: General Safety Information
Installation manual experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 1.1 General safety information The machine is only intended for water-wash use. -
Page 7: Technical Data
Installation manual 2 Technical data 2.1 Drawing fig.8025 Operating panel Detergent container Door opening, ⌀ 255 mm Cold water Hot water Drain valve Drain pump Electrical connection Payment system 832* * Adjustable height: 25 mm. -
Page 8: Technical Data
Installation manual 2.2 Technical data Weight, net Drum volume litres Drum diameter Drum speed during wash 35/54 Drum speed during extraction 1450 Drum speed during extraction, Marine model 1300 G-factor, max. G-factor, max. Marine model Heating: Electricity Heating: Hot water Frequency of the dynamic force 24.2 Floor load at max extraction... -
Page 9: Siting
Installation manual Remove the machine from the pallet. The machine shall be lifted in the bottom frame. Mount the enclosed supporting feet and level the machine. Remount the front- and the back panel. Place the machine on its final position. 3.2 Siting Install the machine close to a floor drain or open drain. -
Page 10: Mechanical Installation
Installation manual 3.3 Mechanical installation If the machine is not to be mounted on a base the machine must be fastened to the floor. Mark and drill two holes (⌀ 8 mm) about 40 mm deep. fig.5358 Place the machine over the two drilled holes. The holes are at the front of the machine. Level the machine with the feet of the machine. -
Page 11: Marine Installation
Installation manual 4 Marine installation The maximum value for rolling is ± 15° and for stamping ± 8°. The machine shall be placed as in the figure. To ensure steadiness of the machine; the machine must be fastened to the floor. Mark and drill two holes (A) ⌀... -
Page 12: Water Connection
Installation manual Thread the holes with M10 bolts. Thread up the four feet of the machine as much as possible. Place the machine at its site. Place the spacers (B) between the machine and the floor. Tighten the machine to the floor with the two bolts. Adjust the feet of the machine to the floor and lock them with the nuts. -
Page 13: Connection Of External Dosing Systems
Installation manual 6 Connection of external dosing systems 6.1 Connection of the hoses The machine is prepared for connection of external dosing systems or water re-use systems etc. There are two versions of hose nipples, follow the instructions for the hose nipples that is provided for your type of machine. -
Page 14: Machine With Connectors
Installation manual 6.2.1 Machine with connectors Connect the external dosing system to connections A and B on the machine. Connect the signal cable to B and the power supply to A. For Efficient dosing system the cables are delivered with the machine. Connect the power supply cable to the machine A and the other end of the cable together with the cable from Effi- cient Dosing in a connection box or with plug and receptacle. -
Page 15: Machine Without Connectors
Installation manual 6.2.2 Machine without connectors Connect the external dosing system to the I/O board, which is located to the right of the incoming power supply. The I/O board has edge connectors for connecting external dosing systems. Edge connectors on the I/O board can be loosened for connecting cables. fig.6238... -
Page 16: Outputs
Installation manual 6.2.3 Outputs Connect the power supply (e.g. 24V DC) for the external liquid supplies to 9 and 10. If an internal power supply (from the machine) is being used, it can be taken from 1 (N) and connected to 9 and from 2 (L) and connected to 10. Max load on the outputs 0.5 A. -
Page 17: Inputs
Installation manual 6.2.4 Inputs The signal level can be 5-24V DC/AC or 100- 240V AC. For 5-24V, the signal reference is connected to 3 and for 100-240V to 4. Potentials on the inputs cannot be mixed. Note! The I/O board will be damaged if the voltage on connection 3 is too high > 24V. Connection 8 may be connected if the program is to pause, e.g. -
Page 18: Drain Connection
Installation manual 7 Drain connection Drain valve The drainage pipe should be located over a floor drain, drainage channel or the like so that the distance between the outlet and the drain is at least 25 mm. fig.2036 Drain pump The drainage pipe should be located over a floor drain, drainage channel or the like. -
Page 19: Electrical Connection
Installation manual 8 Electrical connection 8.1 Electrical installation The electrical installation may only be carried out by qualified personnel. In accordance with the wiring rules: mount a multi-pole switch prior to the machine to facilitate installation and service operations. Connect the machine’s cable to the switch. Check that the earth has been connected in the correct way. -
Page 20: Machine Connection
Installation manual 8.3 Machine connection The machine can be switched/reconnected to the following options. Connection option 380–415V/3N~ 4.4 kW Electric heated Connection option 380–415V/3~ 4.4 kW Electric heated Connection option 208–240V/3~ 4.4 kW Electric heated Connection option 208–240V/1~ 4.4 kW Electric heated Connection option 208–240V/1N~ 4.4 kW Electric heated... - Page 21 Installation manual Connection option 208–240V/1~ 2.2 kW Electric heated Connection option 208–240V/1N~ 2.2 kW Electric heated Connection option 100–240V/1N~ Non heated Connection option 100–240V/1~ Non heated Reconnection/switchover of this type can not be performed on machines fitted with a transformer. The machine can not be switched from 50 Hz to 60 Hz or vice versa.
-
Page 22: Functions For I/O-Cards
Installation manual 8.4 Functions for I/O-cards The electrical schematic can be one of the following: 8.4.1 External coin meter/Central payment (2A) The signal received from external coin meters must be a pulse between 300–3000 ms (500 ms is recommended) with a minimum pause of 300 ms (500 ms is recommended) between two pulses. fig.6606A... -
Page 23: Central Payment (2B)
Installation manual 8.4.2 Central payment (2B) To start the machine from a central payment system, the payment system must transmit a start pulse to the machine. The start pulse can be either 230V or 24V. In order to receive a feedback signal once the machine has started, 230V or 24V must be connected to connection 19. -
Page 24: Central Payment (2C)
Installation manual 8.4.3 Central payment (2C) The central payment or booking system shall transmit an active (high) signal to the machine once permission has been granted to start the machine. The signal must remain active (high) until the machine starts. A feedback signal will be present on connection 18 and remain active (high) whilst the machine door is closed but the program has not started. -
Page 25: Outputs For Detergent Signals And Inputs For Pause Signals, "Empty" Signal And Price Reduction (2D)
Installation manual 8.4.4 Outputs for detergent signals and inputs for pause signals, "empty" signal and price reduction (2D) The figure shows standard function addressing for machines with the coin program package. By maintaining an active (high) signal on connection 5 ("Price red"), the price of the program can be reduced. This function has a number of uses, including providing reductions during a specific period of the day. -
Page 26: Central Booking/Payment (2F)
Installation manual 8.4.5 Central booking/payment (2F) The central payment or booking system shall provide an active (high) signal to the machine once permission has been granted to start the machine. The signal must remain active (high) until the machine starts. A feedback signal will be present on connection 18 and remain active (high) whilst the program is running. -
Page 27: At First Power Up
Installation manual 9 At first power up When the installation is complete and the power is connected for the first time you will be forced to make the following settings. When one setting is ready you will automatically enter the next one. •... - Page 28 Electrolux Laundry Systems Sweden AB 341 80 Ljungby, Sweden www.electrolux.com/professional Share more of our thinking at www.electrolux.com...