Page 1
DZ-MV350A/MV350A(K) service manual. Change 1 Change 2 During the product warranty period, please contact MultiMediaCard 1.800.HITACHI (800.448.2244) for guidance. SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT DVD VIDEO CAMERA/RECORDER March 2003 Digital Media Division,Tokai...
Table of Contents 1 Safety Precaution for Repair ..... 1-1 5 Disassembly and Reassembly ..5-1 1-1 Cautions ........... 1-1 5-1 Preparations for Disassembly ....5-1 1-2 Notes When Using Service Manual ..1-2 5-2 Order of Disassembly ....... 5-1 1-2-1 Value units used in parts list ....
Page 3
3-3 FRT Circuit Board Diagram ....... 14 7 Exploded View and Parts List .... 7-1 3-4 FAF, SAF Circuit Board Diagrams ....14 7-1 Exploded Views ........7-1 3-5 GYR Circuit Board Diagram ....... 15 7-1-1 Main section .......... 7-1 3-6 DRF Circuit Board Diagram .......
The use of a substitute replacement component which does not have the same safety characteristics as the HITACHI recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product safety is continuously under review and new instructions are issued from time to time.
Safety Precaution for Repair > Notes When Using Service Manual 1-2 Notes When Using Service Manual The following shows the contents to be noted when using service manual: 1-2-1 Value units used in parts list Certain symbols are indicated below for value units of resistors, capacitors and coils in parts list. When you read them note the following regular indications: Parts Indication in list...
Safety Precaution for Repair > Notes When Using Service Manual 1-2-4 Table for indexing locations of parts The table of “Identification of parts location” on circuit board diagrams shows locations of each part is below explanations. The locations are indicated using the guide scales on the external lines of diagrams.
Safety Precaution for Repair > Electrostatic Protection Measures 1-3 Electrostatic Protection Measures Semiconductor components, including optical pickups, may be damaged by static electricity charged on clothes, human body, etc. Take great care when handling it to avoid electrostatic damage. 1-3-1 Grounding for prevention of electrostatic damage Perform servicing in an environment where grounding is complete.
Safety Precaution for Repair > Lead-Free Solder 1-4 Lead-Free Solder To protect the global environment, lead-free solder is used in this product. Be sure to read the following before soldering. Caution Be sure to wear protective goggles so that no solder smoke or scattered solder enters the eye during servicing.
General Description Destinations normally added at the end of model names, (K), etc. are omitted in this item. 2-1 Overview The DZ-MV380A DVD video camera/recorder is equipped with mega-pixel CCD and high- performance lens. Since model DZ-MV380A is a higher version of DZ-MV350A, with the CCD and lens changed, it has all the features and functions of DZ-MV350A.
General Description > Overview 2-1-2 Servicing method Table 2-1-1 shows the method for servicing each circuit board and each unit. Refer to "4 Troubleshooting" for the method of judging defects in each circuit board and each unit. Information: These servicing methods are subject to change without notice for the purpose of facilitating service procedures.
General Description > Features 2-2 Features Mounting 1,020,000-pixel CCD (image Round DVD holder sensor) A CCD with a total number of 1,020,000 pixels DVD-RAM/ (the number of effective pixels: 400,000 pixels DVD-R disc for video, 960,000 pixels for photo) is mounted to ensure high resolution and faithful color High-performance lens...
General Description > Specifications 2-3 Specifications The specifications in shaded columns are different from those of previous models. Specifications are subject to change without notice for the purpose of improvement. Item DZ-MV380A DZ-MV350A 1/3.8-inch interlaced 1/4-inch interlaced Total number of pixels: Total number of pixels: Approx.
Page 13
General Description > Specifications Item DZ-MV380A DZ-MV350A Recording DVD-R disc Video: Conforming to DVD video Video: Conforming to DVD video format format (MPEG Audio layer 2 format (MPEG Audio layer 2 or LPCM selected) or LPCM selected) Card Photo: Conforming to JPEG (1280 × Photo: Conforming to JPEG (640 ×...
General Description > Major Differences from Previous Models 2-4 Major Differences from Previous Models Item DZ-MV380A DZ-MV350A 1/3.8-inch interlaced 1/4-inch interlaced Total number of pixels: Total number of pixels: Approx. 1020,000 Approx. 680,000 Number of effective pixels: Number of effective pixels: Video: Approx.
General Description > List of Functions 2-5 List of Functions The list of functions in shaded columns are different from those of previous models. Item DZ-MV380A DZ-MV350A Switching on-screen language English/French/German/Spanish/ English/French/German/Spanish/ Italian Italian Demonstration mode Auto/Off/Start Auto/Off/Start Full Auto button Equipped Equipped Disc protect...
General Description > List of Functions Item DZ-MV380A DZ-MV350A Jacks External Ø 3.5 mm stereo × 1 Ø 3.5 mm stereo × 1 microphone PC connection Type B (mini USB), USB2.0 Type B (mini USB), USB2.0 Accessory shoe Power/control terminal provided Power/control terminal not provided (External flash: DZ-FLH3 mountable) Disc...
General Description > Compatibility of Recorded Discs 2-6 Compatibility of Recorded Discs DVD-RAM and DVD-R discs recorded or edited on DZ-MV380A can also be recorded, edited or played back on other video camera/recorders: However, DZ-MV100A is not compatible with DVD-R disc.
Troubleshooting Destinations normally added at the end of model names, (K), etc. are omitted in this item. 4-1 Procedure for Troubleshooting Perform troubleshooting in the order shown in Fig. 4-1-1. Updating No improvement unneeded Check firmware Trouble System reset Problem guide No message or version (section Check...
Troubleshooting > Trouble Diagnosis 4-7 Trouble Diagnosis 4-7-1 Selecting service position For trouble diagnosis, with a few exceptions it is necessary to disassemble the DZ-MV380A and set it to the service position. There are four types of service position (A)-(D) as shown in the figures below. Refer to Table 4-7-1 and select the appropriate service position for the defective symptom.
Troubleshooting > Trouble Diagnosis 4-7-2 Disassembly/reassembly for enabling service position Prohibition Disconnect the AC adapter/charger of battery pack from the DZ-MV380A. The DZ-MV380A has a built-in laser emitter block. Do not look into it: If Laser beam strikes your eye, it could cause serious damage. To set to service position (A), (B) or (C), remove the following components, referring to “5.
Page 21
Troubleshooting > Trouble Diagnosis (2) Setting to service position (B) (Fig. 4-7-6) Refer to Table 4-7-1 and the MAN and AEL circuit board diagrams: Solder a lead wire of approx. 10 cm to the check point that corresponds to the symptom (except for terminals of IC or connector/ plug).
Page 22
Troubleshooting > Trouble Diagnosis 8) Connect the L block and AEL circuit board via SAF circuit board. (Fig. 4-7-7) AEL CIRCUIT BOARD L BLOCK CIRCUIT BOARD Fig. 4-7-7 Setting to Service Position (C) (4) Setting to service position (D) (Fig. 4-7-8) Remove the following components, referring to “5.
Troubleshooting > Trouble Diagnosis 4-7-3 Trouble diagnosis table Interpreting the trouble diagnosis table: 1) Letters in brackets [ ] in “check points” columns show the name and side of circuit board. Example: [MAN-A] shows that the check point exists on side A of MAN circuit board. 2) If there are multiple check points for one symptom, check the items from the top down.
Page 24
Troubleshooting > Trouble Diagnosis Table 4-7-1 Trouble Diagnosis Table (2/3) Service Troubleshooting due to Symptom Check points Detail of check position check results Error message “NO ----- ----- Error message Check connections of DRF DISC” appears even appears approx. 1 circuit board.
Page 25
Troubleshooting > Trouble Diagnosis Table 4-7-1 Trouble Diagnosis Table (3/3) Service Troubleshooting due to Symptom Check points Detail of check position check results Conspicuous block noise ----- ----- ----- Replace MAN circuit during movie recording board. Camera image is TL2084 [MAN-A] Check CCD sensor NG: Replace MAN circuit abnormal...
Troubleshooting > Procedure for Removing Disc from Faulty DZ-MV380A 4-8 Procedure for Removing Disc from Faulty DZ-MV380A 4-8-1 Item to be checked Connect the AC adapter/charger or charged battery pack, making sure the ACCESS/PC indicator turns off (after the disc rotation stops and the sound showing that the disc lock has been released is heard), and then press the DISC EJECT button again.
Page 27
Troubleshooting > Procedure for Removing Disc from Faulty DZ-MV380A 1) Turn the hood (a) in the direction of the (a) Hood [A] M1.7×4 (Black) (b) Filter Piece arrow to remove it. (See Fig. 4-8-1) (c) Lens Cover 2) Remove three screws [A], and then remove (d) Shoe Cover [X] M2×2.5 (Black) the filter piece (b).
Disassembly and Reassembly 5-1 Preparations for Disassembly (1) Checking Disc Connect the AC adapter/charger or charged battery pack, and then press the DISC EJECT button to make sure that no disc is inserted. After check, close the disc cover. If the disc cover does not open normally, refer to "4-8 Procedure for Removing Disc from Faulty DZ- MV380A", and open the holder.
Page 29
Disassembly and Reassembly > Order of Disassembly Reading Disassembly Flowchart: After locating the target component in the flowchart, remove all components of the target in sequence, following the arrows (routes) from the top of flowchart. If multiple routes exist to the target component from the top of flowchart, remove all the components on all the routes.
Disassembly and Reassembly > Disassembly 5-3 Disassembly Information: Numbers in figures are step numbers in disassemble procedure, and letters in brackets [ ] show the types of screw. Letters in brackets ( ) show the name of parts. (a) Adjustment Cover (1) Adjustment Cover (Fig.
Disassembly and Reassembly > Disassembly (3) Eyecup, SAF Circuit Board, and L Block (Figs. 5-3-3, 5-3-4) Eyecup (a) 1) Pull the EVF unit 2) Remove the eyecup in the direction of the arrow. SAF Circuit Board (b) and L Block (c) 3) Open the LCD monitor.
Disassembly and Reassembly > Disassembly (4) Front Block, FAF Circuit Board, and R Block (Fig. 5-3-5) 1) Open the jack cover (d ), and then remove screw [C] beside the jack. 2) Remove screw [D] from the bottom of front block (a). 3) Remove the front block from R block (c) in the direction of the arrow: Be careful not to damage the FAF circuit board (b) between front block and R block.
Disassembly and Reassembly > Disassembly (5) L Cover, L Case and LCD Block (Fig. 5-3-6) (a) L Cover L Cover (a) (b) L Case 1 [E] 1) Remove five screws [E] and then remove the (c) LCD Block LCD block and fulcrum block (d) assembled (d) Fulcrum Block with L case from the L cover.
Disassembly and Reassembly > Disassembly (7) LCD Case U, MR Circuit Board, and Fulcrum Block (Fig. 5-3-8) LCD Case U (a) 1) Insert a fine-tipped screwdriver (e) into the screw hole in fulcrum block, and then turn the screw hole bracket 90° in the direction of the arrow. 2) Turn the fulcrum block 90°...
Disassembly and Reassembly > Disassembly (8) Disc Cover (Figs. 5-3-9, 5-3-10) 1) Remove four screws [X] and pull up the parts (m) of accessory shoe. After work, reinstall part [m] and screws [X] to the accessory shoe: The accessory shoe is set as a service part, including part [m] and screws [X].
Disassembly and Reassembly > Disassembly (9) USB Circuit Board, Rear Cover, and Hand Strap (Fig. 5-3-11) USB Circuit Board (a) 1) Remove screw [D]. 2) Disconnect the flat cable from MAN circuit board (d), and then remove the USB circuit board assembled with USB holder (e) from the R block.
Disassembly and Reassembly > Disassembly (10) SHE Circuit Board, Accessory Shoe, and EVF Unit (Fig. 5-3-12) SHE Circuit Board (a) and Accessory Shoe (b) 1) Disconnect the SHE circuit board from AEL circuit board (d) in the direction of the arrow. 2) Disconnect the two flat cables from SHE circuit board.
Disassembly and Reassembly > Disassembly (11) AEL and MAN Circuit Boards (Fig. 5-3-13) 1) Disconnect the flat cable from AEL circuit board (a). 2) Disconnect the SHE circuit board (c) in the direction of the arrow from the AEL circuit board. 3) Disconnect the DRF circuit board (d) in the direction of the arrow from the MAN circuit board.
Disassembly and Reassembly > Disassembly (12) Camera Block (Fig. 5-3-14) 1) Disconnect the SEN circuit board (b) from MAN circuit board (c) in the direction of the arrow. 2) Disconnect the flat cable from AEL circuit board (d). 3) Disconnect the GYR circuit board (e) from SHE circuit board (f). 4) Remove two screws [H].
Disassembly and Reassembly > Disassembly (13) LCD Circuit Board, Backlight, LCD Unit , and LCD Case B (Fig. 5-3-15) LCD Circuit Board (a) 1) Unsolder the two points on LCD circuit board. 2) Disconnect the flat cable from LCD circuit board. 3) Remove screw [H], and then remove the LCD circuit board.
Disassembly and Reassembly > Disassembly (14) Link Bracket, Drive Block, and R Case (Figs. 5-3-16, 5-3-17, 5-3-18) Link Bracket (a) (Fig. 5-3-16) 1) Remove two screws [K], and then remove the link bracket. Drive Block (b) and R Case (c) (Figs. 5-3-16, 5-3-17, 5-3-18) 2) Remove screw [D].
Disassembly and Reassembly > Disassembly (15) Fulcrum Cover U and Fulcrum Cover B (Fig. 5-3-19) 1) Remove two screws [D] and then remove the (a) Fulcrum Cover U fulcrum cover U (a) and fulcrum cover B (b). (b) Fulcrum Cover B 1 [D] [D] M1.6×2.5 (Black) Fig.
Disassembly and Reassembly > Disassembly (17) Loader, DRF Circuit Board, Disc Drive Unit, and Lock Unit (Fig. 5-3-21) Loader (a) 1) Remove two screws [M], and then remove the loader from disc drive unit. Note: Do not subject the loader to undue force: If the loader is damaged, discs cannot be inserted or recognized.
Exploded View and Parts List 7-1 Exploded Views Note: Components without any numbers in exploded views had not been assigned as service parts as of the date of issue 7-1-1 Main Section of this manual. USB CIRCUIT BOARD DVD DRIVE UNIT [Component [Unit Replacement SHE CIRCUIT...
2-2 FRT Schematic Diagram 2-3 FAF Schematic Diagram CN1801 CODE PART NAME 2SC5383T11 2SD2345-S DTC114YE MA132WA ONE VOLTAGE:PB OR REC MODE TWO VOLTAGES:PB AND (REC) MODE BOARD To BOARD PG1801 [AEL] PG7003 R1812 0 RECEIVER 0(3) 2-4 SAF Schematic Diagram R1802 0 L CASE BOARD To BOARD...
IC3401 2-15 IC Block Diagram CXA3582R LCD DRIVER MODE PICTURE Gain PICTURE PICTURE PSIG- BRIGHT MATRIX SYNC IN COLOR DA OUT MUE COLOR G OUT R,G,B G DC DET USER- GAMMA1 SUB- CONTRAST CONTRAST BRIGHT GAMMA2 BRIGHT TRAP FILTER R OUT USER- CONTRAST BRIGHT...
Page 63
IC3701 CXA3503R EVF DRIVER GND3 +12.0V +12.0V +3.0V G OUT OSD RGB TST15 G DC DET FILTER CONTRAST USER-BRIGHT CONT U-BRT OSD B R OUT FILTER TRAP GAMMA OSD R BIAS R DC DET WHITLIM CLAMP SUB-CONT R OSD G B OUT SUB-CONT B BLK-LIM...
3-13 SID Circuit Board Diagram 3-14 HDM Circuit Board Diagram Information of MAN, DRV, SID and HDM Circuit Boards (4.8) During servicing, replace the entire MAN circuit board, and the entire disc drive unit, including the DRV, SID and HDM circuit boards.
3-15 Identification of Parts Location Symbol Parts Symbol Parts Symbol Parts Symbol Parts Symbol Parts Symbol Parts Symbol Parts Symbol Parts Symbol Parts Location Location Location Location Location Location Location Location Location R3435 C3895 A-3D C6323 A-1B Q3892 A-2E R3705 A-2E R6135 A-2C...
4. Block Diagrams 4-1 Video/Audio Signal Process Section Block Diagram IC1504 OPERATION EEPROM IC0501 : REC VIDEO/CCD OUT IC3701 : PB VIDEO EVF UNIT EVF DRIVER AC ADPTER/ POWER CHARGER OR CONTLOR : EXT.INPUT VIDEO BATTERY PACK [Refer to power-1] IC1401, REAL TIME IC1402...
4-2 Disc Drive Section Block Diagram 8cm DVD-RAM/DVD-R DISC Video/Audio Disc Drive Unit Signal Process Section Head SPINDLE MOTOR SDRAM ANALOG FRONT END LASER DATA IC2006 STROBE CAMERA DSP & DIODE MPEG2 CODEC LASER DIODE Recode DRIVE DRIVE DSP (SERVO/DSP/ FRONT MONITOR ATAPI/ DET.