Pioneer Elite PRO-1000HDI Operating Instructions Manual page 23

8
When inputting a video signal (When VIDEO is
selected), press 5/∞ to select VIDEO SIGNAL.
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
A UT O P O WER
C OL OR T M E P
D I G I T A L NR
H I GH C O T N R A T
P URE C N MA I E
C L AM P P S I T I O N O
S E T T I N G
V I D E O S I GNA L
SELECT
SET
9
Press SET repeatedly to select the input signal
format.
Selection will change as follows each time SET is
pressed.
RGB
COMPONENT
The table below shows what settings are appropriate
and available for the type of connections made.
Set SETTING and VIDEO SIGNAL as follows.
SET UP
SETTING
Connected
component
Component video output VIDEO
of a DVD player, etc.
RGB video output of a VIDEO
video deck etc., with RGB
output
RGB video output of a PC VGA
WVGA
XGA
WXGA
10
When the setup is completed, press MENU to exit
the menu screen.
Note
Make this setup for each input (INPUT1 and INPUT2).
INPUT1
SET UP OPTION
:
I N P UT 1
: OF F
OF F
: M I D DL E
: L OW
: O F F
S
: O F F
: A U T O
: V I D E O
: R G B
CHANGE EXIT
MENU
VIDEO SIGNAL
COMPONENT
RGB
Not supported
Setting Up the System
CLAMP POSITION setup
Depending on the signal, analog RGB signals may result
in the screen image appearing with a whitish or greenish
cast. In such cases, set "CLAMP POSITION" to LOCKED.
÷ Normally, leave this setting at AUTO.
Setup of CLAMP POSITION
1
Press MENU to display the menu screen.
The menu screen appears.
MAIN MENU
PICTURE SCREEN
:
CO NT RA S T 0
:
BR I GHT . 0
: 6 +
R L E V E L . 0
: 6 0
+
G L E V E L .
: 6 0
+
B L E V E L .
:
H E NH AN CE . 0
:
V E NH AN CE . 0
R S E T E
SELECT ENTER
SET
2 Press 2/3 to select SET UP.
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
3 Press 5/∞ to select CLAMP POSITION.
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
POWE R M NA GEME A
C L A MP P S I T I O N O
S E T T I N G
4
Press SET to select LOCKED.
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
POWE R M NA GEME A
C L A MP P S I T I O N O
S E T T I N G
Mode selection will change as follows each time SET
is pressed.
3 AUTO
LOCKED 2
5
When the setup is completed, press MENU to exit
the menu screen.
Notes
÷ Make this CLAMP POSITION setting for each applicable input
(INPUT1 and INPUT2).
÷ When using this setup, be sure to carefully check the signal
output of the component that you are using. For details, please
refer to the instruction manual supplied with the component
you are connecting.
INPUT1
SET UP OPTION
EXIT
MENU
INPUT1
SET UP OPTION
:
I N P UT 1
:
NT OF F
: A U T O
: V G A
INPUT1
SET UP OPTION
:
I N P UT 1
:
NT OF F
: A U T O
: V G A
INPUT1
SET UP OPTION
:
I N P UT 1
:
NT OF F
: L O CK E D
: V G A
19
I I
PRO-1000HD / PRO-800HD