Hitachi SJ300 Series Manual page 14

Code Name
A041 Torque boost method selection
A241 Torque boost method selection for second motor
A042 Manual torque boost value
A242 Manual torque boost value for second motor
A342 Manual torque boost value for third motor
A043 Manual torque boost frequency adjustment
A243 Manual torque boost frequency adjustment for second motor
Manual torque boost frequency adjustment for third motor
A343
A044 V/f characteristic curve selection
V/f characteristic curve selection for second motor
A244
A344 V/f characteristic curve selection for third motor
A045 V/f gain setting
A051 DC braking enable
A052 DC braking frequency setting
A053 DC braking wait time
A054 DC braking force setting
A055 DC braking time setting
A056 DC braking edge or level detection
A057 DC braking force setting at the starting point
A058 DC braking time setting at the starting point
A059 DC braking carrier frequency setting
A061 Frequency upper limit setting
Frequency upper limit setting for second motor
A261
A062 Frequency lower limit setting
A262 Frequency lower limit setting for second motor
A063 Jump frequency (1) setting
A064 Jump frequency width (1) setting
A065 Jump frequency (2) setting
A066 Jump frequency width (2) setting
A067 Jump frequency (3) setting
A068 Jump frequency width (3) setting
A069 Acceleration stop frequency setting
A070 Acceleration stop time setting
A071 PID function enable
A072 PID proportional constant
A073 PID integral time constant
A074 PID derivative time constant
A075 Process variable scale conversion
A076 Process variable source setting
A081 AVR function selection
A082 AVR voltage selection
Operation mode selection
A085
A086 Energy saving mode tuning
A092 Acceleration time (2)
Acceleration time (2) for second motor
A292
A392 Acceleration time (2) for third motor
A093 Deceleration time (2)
A293 Deceleration time (2) for second motor
A393 Deceleration time (2) for third motor
A094 Select method to switch to second accel./decel. profile
A294 Select method to switch to second accel./decel. profile for second motor
Accel(1) to Accel(2) frequency transition point
A095
A295 Accel(1) to Accel(2) frequency transition point for second motor
A096 Decel(1) to Decel(2) frequency transition point
Decel(1) to Decel(2) frequency transition point for second motor
A296
A097 Acceleration curve selection
A098 Deceleration curve selection
A101 OI-L input active range start frequency
A102 OI-L input active range end frequency
A103 OI-L input active range start current
A104 OI-L input active range end current
A105 OI-L input start frequency enable
A111 O2-L input active range start frequency
A112 O2-L input active range end frequency
O2-L input active range start voltage
A113
A114 O2-L input active range end voltage
A131 Acceleration curve constants setting
A132 Deceleration curve constants setting
Note:[ ]75kW and over
Description
00(Manual torque boost) / 01(Automatic torque boost)
00(Manual torque boost) / 01(Automatic torque boost)
0.0 - 20.0%
0.0 - 20.0%
0.0 - 20.0%
0.0 - 50.0%
0.0 - 50.0%
0.0 - 50.0%
00(VC)/ 01(VP 1.7th power)/ 02(V/f free-setting)/ 03(SLV)
/ 04(SLV at around 0Hz)/ 05(Vector control with encoder feedback)
00(VC)/ 01(VP 1.7th power)/ 02(V/f free-setting)/ 03(SLV)/ 04(SLV at around 0Hz)
00(VC) / 01(VP 1.7th power)
20. - 100.
00(Disable) / 01(Enable)
0.00 - 60.00Hz
0.0 - 5.0sec.
0. - 100.% [0. - 80.(%)]
0.0 - 60.0sec.
00(Edge) / 01(Level)
0.-100.% [0. - 80.(%)]
0.0-60.0sec.
0.5 - 15kHz (To be derated) [0.5 - 10kHz]
0.00, Starting frequency to maximum frequency
0.00, Starting frequency to maximum frequency for second motor
0.00, Starting frequency to maximum frequency
0.00, Starting frequency to maximum frequency for second motor
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 10.00Hz
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 10.00Hz
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 10.00Hz
0.00 - 99.99 / 100.0 - 400.0Hz
0.0 - 60.0sec.
00(Disable) / 01(Enable)
0.2 - 5.0
0.0 - 3600.sec.
0.0 - 100.0sec.
0.01 - 99.99%
00(at OI) / 01(at O)
00(Always ON) / 01(Always OFF) / 02(OFF during deceleration)
200/215/220/230/240, 380/400/415/440/460/480V
00(Normal operation)/ 01(Energy-saving operation)
/ 02(Fuzzy operation)
0.0 - 100.0
0.01 - 99.99 / 100.0 - 999.9 / 1000. - 3600.sec.
0.01 - 99.99 / 100.0 - 999.9 / 1000. - 3600.sec.
0.01 - 99.99 / 100.0 - 999.9 / 1000. - 3600.sec.
0.01 - 99.99 / 100.0 - 999.9 / 1000. - 3600.sec.
0.01 - 99.99 / 100.0 - 999.9 / 1000. - 3600.sec.
0.01 - 99.99 / 100.0 - 999.9 / 1000. - 3600.sec.
00(2CH input from terminal) / 01(Transition frequency)
00(2CH input from terminal) / 01(Transition frequency)
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 99.99 / 100.0 - 400.0Hz
00(Linear) / 01(S-curve) / 02(U-shape) / 03(Reverse U-shape)
00(Linear) / 01(S-curve) / 02(U-shape) / 03(Reverse U-shape)
0.00 - 99.99 / 100.0 - 400.0Hz
0.00 - 99.99 / 100.0 - 400.0Hz
0. - 100.%
0. - 100.%
00(External frequency output zero reference) / 01(0Hz)
-400. - 400.Hz
-400. - 400.Hz
-100. - 100.%
-100. - 100.%
01(Smallest deviation) - 10(Largest deviation)
01(Smallest deviation) - 10(Largest deviation)
[ = Allowed
⃝
= Not permitted
×
Default Setting
Run-time Run-time Data Edit
Setting (Enabled at b031)
-FE(CE) -FU(UL)
00 00 × ×
00 00 × ×
1.0 1.0
⃝ ⃝
1.0 1.0
⃝ ⃝
1.0 1.0
⃝ ⃝
5.0 5.0
⃝ ⃝
5.0 5.0
⃝ ⃝
5.0 5.0
⃝ ⃝
00 00 × ×
00 00 × ×
00 00 × ×
100. 100.
⃝ ⃝
00 00 ×
⃝
0.50 0.50 ×
⃝
0.0 0.0 ×
⃝
0. 0.
×
⃝
0.0 0.0 ×
⃝
01 01 ×
⃝
0. 0. ×
⃝
0.0 0.0 ×
⃝
5.0[3.0] 5.0[3.0] × ×
0.00 0.00 ×
⃝
0.00 0.00 ×
⃝
0.00 0.00 ×
⃝
0.00 0.00 ×
⃝
0.00 0.00
×
⃝
0.50 0.50 ×
⃝
0.00 0.00 ×
⃝
0.50 0.50 ×
⃝
0.00 0.00 ×
⃝
0.50 0.50 ×
⃝
0.00 0.00 ×
⃝
0.0 0.0 ×
⃝
00 00 ×
⃝
1.0 1.0
⃝ ⃝
1.0 1.0
⃝ ⃝
0.0 0.0
⃝ ⃝
1.00 1.00 ×
⃝
00 00 ×
⃝
00 00 × ×
230/400 230/460 × ×
00 00 × ×
50.0 50.0
⃝ ⃝
15.00 15.00
⃝ ⃝
15.00
15.00
⃝ ⃝
15.00 15.00
⃝ ⃝
15.00 15.00
⃝ ⃝
15.00 15.00
⃝ ⃝
15.00 15.00
⃝ ⃝
00 00 × ×
00 00 × ×
0.00 0.00 × ×
0.00 0.00 × ×
0.00 0.00 × ×
0.00
0.00 × ×
00 00 × ×
00 00 × ×
0.00 0.00 × ×
0.00 0.00 ×
⃝
20. 20. ×
⃝
100. 100. ×
⃝
01 01 ×
⃝
0.00 0.00 ×
⃝
0.00 0.00 ×
⃝
-100. -100. ×
⃝
100. 100. ×
⃝
02 02 ×
⃝
02 02 ×
⃝
]
14