Related Manuals for Kenwood TK-D740H
Summary of Contents for Kenwood TK-D740H
- Page 1 TK-D740H TK-D740HV TK-D840H TK-D840HU USER GUIDE GUIDE DE L'UTILISATEUR GUÍA DEL USUARIO B5A-0922-00 (K)
-
Page 3: User Guide
VHF DIGITAL TRANSCEIVER TK-D740H TK-D740HV UHF DIGITAL TRANSCEIVER TK-D840H TK-D840HU USER GUIDE This User Guide covers only the basic operations of your radio. Ask your dealer for information on any customized features they may have added to your radio. For using details instruction manual (User Manual), refer to the following URL. -
Page 4: Table Of Contents
THANK YOU We are grateful you have chosen KENWOOD for your Digital Transceiver applications. CONTENTS NOTICES TO THE USER ................3 PRECAUTIONS ..................4 TERMINAL DESCRIPTIONS ..............5 UNPACKING AND CHECKING EQUIPMENT ............6 SUPPLIED ACCESSORIES ................... 6 PREPARATION ..................7 ORIENTATION ..................9 FRONT/ REAR PANEL ....................9 DISPLAY ........................ -
Page 5: Notices To The User
This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/ JVC KENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. -
Page 6: Precautions
U.S. Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and #8,359,197 Firmware Copyrights The title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation. PRECAUTIONS Observe the following precautions to prevent fi re, personal injury, and transceiver damage. -
Page 7: Terminal Descriptions
TERMINAL DESCRIPTIONS ACC (D-SUB 15 Pin Connector) Pin No. Name Description Specifi cation DC Power (Switched B) Output 13.6 V ±15% Max. 1 A Min. Input: 10.8 V Igintion Signal Input Max. Input: 16.0 V 4 SP2/PA Loudspeaker Output/ Public Address Output DETO RX Detected Audio Output 280 mV... -
Page 8: Unpacking And Checking Equipment
• KMC-30 <TK-D740H/ TK-D840H> ........ -
Page 9: Preparation
PREPARATION Various electronic equipment in your vehicle may malfunction if they are not properly protected from the radio frequency energy which is present while transmitting. Typical examples include electronic fuel injection, anti-skid braking, and cruise control. If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally while transmitting. - Page 10 4 Mount the microphone hanger in a location where it will be within easy reach of the user. • The microphone and microphone cable should be mounted in a place where they will not interfere with the safe operation of the vehicle. When replacing the fuse in the DC power cable, be sure to replace it with a fuse of the same value.
-
Page 11: Orientation
ORIENTATION FRONT/ REAR PANEL ACC. (Power) switch Press to switch the transceiver ON or OFF. keys Press to activate their programmable functions. Display Refer to page 9. keys Press to activate their programmable functions. TX/RX Indicator Lights red while transmitting. Lights green while receiving a signal. Flashes orange when receiving an optional signaling call. -
Page 12: Display
Power input connector Connect the DC Power Cable to this connector. DISPLAY The display shows the zone/ channel number and the 2 dots show various modes of operation. Display Description Display Description Appears when a channel is Zone Display (Zone 1) added to the scan list. -
Page 13: Basic Operation
BASIC OPERATION SWITCHING POWER ON/ OFF Press [ ] to switch the transceiver ON. Press [ ] again to switch the transceiver OFF. ADJUSTING THE VOLUME Press the key programmed as [Volume Up] to increase the volume. Press the key programmed as [Volume Down] to decrease the volume. SELECTING A ZONE AND CHANNEL Select the desired zone and channel using the keys programmed as [Zone Up]/ [Zone Down] and [Channel Up]/ [Channel Down]. - Page 14 © 2015...
- Page 15 MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antennas. • Antenna Minimum Safe Distance: 40 cm (16 inches), 50% duty Cycle. • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 40 cm (16 inches) , 50% duty Cycle. • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. •...