Page 1
MH240 Wireless IP Telephone SETUP GUIDE Preliminary Issue, January 2008...
Page 3
NEC Infrontia Corporation reserves the right to change the specifications, functions, or features, at any time, without notice. NEC Infrontia Corporation has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Infrontia Corporation and shall not be reproduced without prior written approval from NEC Infrontia Corporation.
TABLE OF CONTENTS SETUP OF THE PHONE • MH240 SETUP PROCEDURE ..............1 • SETUP FROM MH240 ................2 • POWER ON MH240 .................. 3 • INITIALIZE MH240 ..................4 • PLACE THE PHONE IN CONFIG MODE ..........5 • WIRELESS SETTINGS................6 Set the Profile Name: ......................6...
Using IP Phone Manager for MH240 via USB cable Using IP Phone Manager for MH240 via WLAN connection Note: To set certificate for WLAN authentication, be sure to use IP Phone Manager for MH240. The data can not be set from MH240.
• SETUP FROM MH240 Follow the procedure below to setup MH240 from the phone. Be sure to change the battery before this setup procedure. START Power on MH240. Initialize MH240 data as required. Place MH240 in configuration mode. Setup the config data.
• POWER ON MH240 STEP1: Press and hold key for 2 seconds or more. The start screen appears as follow. Note: About 30 seconds will be required for displaying the start screen. STEP2: The screen is placed in Standby mode.
• INITIALIZE MH240 Initialize MH240 as required. By doing this procedure, the following data will be initialized. Config (configuration data) Directory Call History Speed Dial / Preset Dial Date & Time Password STEP1: Press key in Standby mode to display the main menu.
• PLACE THE PHONE IN CONFIG MODE To set administrator-related data such as Network, WLAN and SIP data, place the phone in Config mode. Config Password entry is required to do this. STEP1: Press key in Standby mode to display the main menu. 1/ 1 Tue 12:00AM STEP2: Press...
• WIRELESS SETTINGS This section explains the wireless data for the phone. The following items are covered here. Set the Profile Name Set the ESSID (Manual) Set the ESSID (AP Scan) Set the Security (OPEN) Set the Security (WEP) Set the Security (WPA-PSK) Set the Security (WPA2-PSK) Set the Security (WPA) Set the Security (WPA2)
Set the ESSID (Manual): Factory Default: default (1.DEFAULT) STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to go to ESSID edit screen.
Set the ESSID (AP Scan): Factory Default: default (1.DEFAULT) STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to scan AP and then view Scanned ESSID list.
Set the Security (OPEN): Factory Default: OPEN STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to set security and then press “OK” soft key. STEP4: Press to go to Security setting screen.
Set the Security (WEP): Factory Default: OPEN STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to set security and then press “OK” soft key. STEP4: Press to go to Security setting screen.
Set the Security (WPA-PSK): Factory Default: OPEN STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to set security and then press “OK” soft key. STEP4: Press to go to Security setting screen.
Set the Security (WPA2-PSK): Factory Default: OPEN STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to set security and then press “OK” soft key. STEP4: Press to go to Security setting screen.
Set the Security (WPA): Factory Default: OPEN STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to set security and then press “OK” soft key. STEP4: Press to go to Security setting screen.
Page 20
STEP10: Press to go Password edit screen. Password aaabbbccc111 Clear STEP11: Edit Password and then press “OK” soft key. STEP12: Press to save. NOTE: If you want to set TLS as EAP type, please use IP Phone Manager for MH240.
Set the Security (WPA2): Factory Default: OPEN STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to set security and then press “OK” soft key. STEP4: Press to go to Security setting screen.
Page 22
STEP10: Press to go Password edit screen. Password aaabbbccc111 Clear STEP11: Edit Password and then press “OK” soft key. STEP12: Press to save. NOTE: If you want to set TLS as EAP type, please use IP Phone Manager for MH240.
Set the DHCP (IP): Factory Default: Fixed IP STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to enable DHCP.
Set the Net Mask: Factory Default: 255.255.0.0 (1.DEFAULT) STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to go to Net Mask edit screen.
Set the Gateway: Factory Default: - STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to go to Gateway edit screen.
Set the DNS Primary: Factory Default: - STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to go to DNS Primary edit screen.
Set the DNS Secondary: Factory Default: - STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Profile Select menu. Prof. Select 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Delete Back STEP3: Press key to select a profile you want to edit and then press “OK” soft key. STEP4: Press to go to DNS Secondary edit screen.
Set the Handover List: Factory Default: DEFAULT STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to view Handover List. HandoverList 1.DEFAULT 2.<Profile2> 3.<Profile3> 4.<Profile4> Back STEP3: Press key to select a profile area you want and then press “OK” soft key. STEP4: Press “OK”...
• SIP SETTINGS This section explains the SIP data for the phone. The following items are covered here. Set the DHCP (SIP) Set the SIP Proxy Set the SIP Port Set the Register Set the Register Port Set the User ID Set the User Password Set the Phone No.
Set the SIP Port: Factory Default: 5070 (SIP Port1) STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to go to SIP Port1 edit screen. SIP Port1 5070 Clear STEP3: Edit SIP Prort and then press “OK” soft key. STEP4: Press to save.
Set the User ID: Factory Default: 240 STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to go to User ID edit screen. User ID Clear STEP3: Edit User ID and then press “OK” soft key. STEP4: Press to save.
Set the Phone No.: Factory Default: 240 STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”) STEP2: Press to go to Phone No. edit screen. Phone No. Clear STEP3: Edit Phone No. and then press “OK” soft key. STEP4: Press to save.
Edit New Config Password (4 digits) and then press “OK” soft key. STEP3: Press to return to Standby mode. NOTE: This procedure is available only when MH240 has been initialized. Change the Config Password: STEP1: Go to “Config” menu. (See “PLACE THE PHONE IN CONFIG MODE”)
• CONFIG MENU LIST The following shows Config menu list of MH240 with the default values and remarks as required. Category Menu Default Remarks Config [MENU-5-3-1] 1.Wireless Need Config Password 2.SIP Settings 3.Config Password...
Page 38
• CHARACTER CODE LIST The following shows character code list when your phone is in edit mode. Character Code List 10th 11th ” ’ < > [space] & ¥...
ROUBLE HOOTING • MESSAGE MEANINGS AND SUGGESTIONS The following shows the meanings and suggestions of messages that may be displayed on your phone. Message Meaning & Suggestion [Password] The entered password is not correct. Enter the correct UnAuthorized! password. [Low Battery] Battery charge level is low.
• TROUBLES AND SUGGESTIONS The following shows suggestions on how to resolve MH240 operation problems. Confirm the following before making a call: Is power ON? Is battery charged? Is Antenna icon ( ) displayed? Symptom Suggestion Press key and hold more than 2 seconds.