Sealey AB931 Instructions

Issue: 1
Date: 200203
Item Part No Description Item Part No
1 AB931/01 Housing Right 11 AB931/11 O-Ring
2 AB931/02 Housing Left 12 AB931/12 Bushing
3 AB931/03 Gravity Cup 13 AB931/13 Screw
4 AB931/04 Cap, Gravity Cup 14 AB931/14 Trigger
5 AB931/05 O-Ring 15 AB931/15 Spring, Trigger
6 AB931/06 Seat, Nozzle 16 AB931/16 Plunger
7 AB931/07 Fluid Cap 17 AB931/17 Cap, Valve Upper End 27 AB931/27
8 AB931/08 Nozzle, .03mm 18 AB931/18 O-Ring
9 AB931/09 Needle 19 AB931/19 Cap, Valve Lower End 29 AB931/29
10 AB931/10 Cap, Nozzle Seat 20 AB931/20 O-Ring
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date. proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions, call us on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500 01284 703534
PARTS DIAGRAM AND LIST FOR:
AIR BRUSH KIT
AB931
Model No:
Description Item Part No Description
21 AB931/21 Spring, Plunger
22 AB931/22 Housing, valve
23 AB931/23 Cap, End
24 AB931/24 Fluid Adj. Screw
25 AB931/25 Inlet
26 AB931/26 Hose Assembly
Nut, Adjustment Screw
28 AB931/28 Fluid Inlet Screw
Air Reg Valve
30 AB931/30 Adaptor, Air Hose
email
9A>
sales@sealey.co.uk www.sealey.co.uk
AB931 - 1 - 200203
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according
to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH
CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP
INSTRUCTIONS SAFE FOR FUTURE USE.
1.

SAFETY INSTRUCTIONS

F
WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations
are adhered to when using tools.
!
Ensure that the air brush and accessories are in a clean, sound condition and good working order. Take
action for immediate repair or replacement of damaged parts. Use recommended parts only. The use of
unauthorised parts may be dangerous and will invalidate the warranty.
!
Ensure the air brush supply hose is not tangled, twisted or pinched.
%
DO NOT use air brush or accessories if damaged.
%
DO NOT operate air brush while under the influence of drugs, alcohol or intoxicating medication, or if fatigued.
&
DO NOT direct spray against yourself, other persons or animals, electrical equipment or the machine itself.
%
DO NOT use the air brush for a task it is not designed to perform.
!
Wear approved eye protection and a suitable respirator when painting. A full range of personal safety
equipment is available from your Sealey Dealer.
%
DO NOT allow smoking or open flame in the work area.
2. ASSEMBLY
Note: Numbers in brackets refer to item numbers
in the parts diagram.
2.1. Screw the gravity cup (3) into the top of the
nozzle seat (6).
2.2. Screw one end of the hose assembly (26) onto
the inlet (25).
2.3. Screw the other end of the hose assembly (26)
to the air supply.
2.4. When using a compressor (Sealey Model
No. AB900), connect the hose assembly (26)
to the air hose adaptor before
connecting to the compressor, fig.1.A.
2.5. When using a propellant can (Sealey Model
No. AB/P), connect the hose assembly (26)
to the air regulator valve (29).
2.6. Ensure the valve is turned fully anti-clockwise before screwing to the top of the propellant can, fig.1.B.
3. OPERATING INSTRUCTIONS
3.1. Mask the area which is NOT to be painted.
3.2. Ensure the object to be painted is free from dust and grease etc.
3.3. After mixing and thinning the paint, as instructed by the paint manufacturer, fill the gravity cup just over
half full and replace the lid.
Note:You can mix any colour combinations required for use with your air brush, but ONLY mix compatible paints,
i.e mix enamels with enamels, lacquers with lacquers and so on. Mix thoroughly, making sure that the
paint is free from lumps. It may be necessary to strain the paint first.
3.4. Turn the air ON and test your spray on old newspaper or other material to get the “feel” of your air brush.
Note: When using quick drying paints, it is advisable to clean or immerse the fluid end of the air brush in a
compatible solvent between sprays.
3.5. Make any necessary spray adjustments. The paint flow and spray pattern are adjusted by turning the fluid
cap at the front of the air brush. The cap is completely closed when it has been turned clockwise to the
stop point. To obtain various degrees of paint flow, turn the cap anti-clockwise. The maximum flow will be
attained by turning the cap approximately 4 half turns anti-clockwise.
INSTRUCTIONS FOR :
AIR BRUSH KIT
AB931
Model:
AB931 - 1 - 200203