Kenwood TS-890S Command Reference Manual page 42

MA0
Memory Channel Configuration
1 2 3
M A 0
11 12 13
P2 P2 P2
21 22 23
Set
P6 P6 P7
31 32 33
P8 P8 P8
x
P13 ;
1 2 3
Read
M A 0
1 2 3
M A 0
11 12 13
P2 P2 P2
21 22 23
Answer
P6 P6 P7
31 32 33
P8 P8 P8
x
P13 ;
MA1
Memory Channel (Direct Write)
1 2 3
M A 1
Set
11 12 13
P1 P1 P1
PC Control Command referenCe guide
4 5 6 7 8
P1 P1 P1 P2 P2
14 15 16 17 18
P2 P2 P2 P2 P3
24 25 26 27 28
P7 P8 P8 P8 P8
34 35 36 37 38
P8 P8 P9 P10 P11
4 5 6 7 8
P1 P1 P1 ;
4 5 6 7 8
P1 P1 P1 P2 P2
14 15 16 17 18
P2 P2 P2 P2 P3
24 25 26 27 28
P7 P8 P8 P8 P8
34 35 36 37 38
P8 P8 P9 P10 P11
4 5 6 7 8
P1 P1 P1 P1 P1
14 15 16 17 18
P1 P2 P3 ;
Parameters:
P1 (Channel number )
9 10
000 ~ 119
P2 P2  Channels P0 ~ P9 are represented as 100 ~ 109 and
channels E0 ~ E9 are represented as 110 ~ 119.
19 20
P2 (Frequency information (11 digits in Hz.))
P4 P5  Blank digits must be entered as "0".
P3 (Mode Information)
29 30
 Refer to the P2 value of the OM command.
P8 P8
P4 (FM Normal/ Narrow information)
0: Normal
39 40 ~
1: Narrow
P12 P13
P5 (FM tone type)
0: OFF
1: Tone
2: CTCSS
9 10
3: Cross Tone
P6 (Tone frequency)
 Refer to the P1 value of the TN command.
9 10
P7 (CTCSS frequency)
P2 P2
 Refer to the P1 value of the CN command.
P8 (Split transmission frequency information (11 digits))
19 20
 Blank digits must be entered as "0".
P4 P5
P9 (Split Transmission mode information )
29 30
 Refer to the P2 value of the OM command.
P10 (Split Transmission FM Normal/ Narrow information)
P8 P8
0: Normal
39 40 ~
1: Narrow
P12 P13
P11 (Split information)
0: Simplex
1: Split
P12 (Scan lockout)
0: Lockout OFF
1: Lockout ON
P13 (Channel name)
Up to 10 characters
• When setting the channel currently being accessed, the new
settings are reflected the next time that channel is accessed.
• When the Programmable VFO is in the process of being read, it
cannot be set.
• When reading a blank channel, parameters P2 to P12 becomes
blank.
• When reading a single memory channel, all parameters for Split
Transmission become 0.
• When setting the split memory channel, set the same setting
on the transmission side and the reception side for FM normal /
narrow information (P4, P10).
Parameters:
P1 (Frequency information (11 digits in Hz.))
9 10
 Blank digits must be entered as "0".
P1 P1 P2 (Mode information
 Refer to the P2 value of the OM command.
19 20
P3 (FM Normal/ Narrow information)
0: Normal
1: Narrow
 In modes other than FM, this parameter is ignored.
• The frequency 1 information of the memory channel which was
appointed when using this command is updated
• When writing to an unregistered section specification memory
channel, the start frequency and the end frequency are
registered as the same frequency.
• When writing to the registered Programmable VFO, if the
specified frequency is within the registered section, this
command is accepted and stored as the current operation
frequency. The start/end frequency is not rewritten.
• When the AI function is ON, a response can consist of the MA0
command.
– 41 –