Page 1
Operating Instruction 42/18-46-EN Rev. L TEIP11, TEIP11-PS I/P signal converter...
Page 2
Short product description I/P signal converter for controlling pneumatic actuators or pneumatic positioners for positioning valves. Further information Additional documentation on TEIP11, TEIP11-PS is available for download free of charge at www.abb.com/positioners. Alternatively simply scan this code: Manufacturer ABB Automation Products GmbH Measurement &...
Safety Intended use I/P signal converters for standard signals TEIP11 and TEIP11- Change from one to two columns PS are used to control pneumatic actuators or pneumatic General information and instructions positioners for positioning valves. These instructions are an important part of the product and must be retained for future reference.
60 °C or below -20 °C, use cable entries and cables Special Requirements suited to an operating temperature that corresponds to the The I/P converter TEIP11-PS Doc. type 901069 or Doc. maximum ambient temperature plus 10 K or that corresponds 901069-SMD must be set up outdoors as a pneumatic power to the minimum ambient temperature.
"intrinsically safe (Ex ia)" type of protection, as the electronics may have been damaged. For this reason the devices must be permanently marked during commissioning (e.g. cross out or mask over "Ex ia"). 6 42/18-46-EN Rev. L | TEIP11, TEIP11-PS...
Principle of operation 3.1.1 Special features Special features of the TEIP11, TEIP11-PS I/P signal converter are its relatively small dimensions and outstanding operational stability when subject to shock and vibration. The stability is 0 … 20 / 4 … 20 mA...
A mounting base that is compatible with all commercially available EN rails is used for installation. The housing unit with plastic cap has an IP 20 protection class. 8 42/18-46-EN Rev. L | TEIP11, TEIP11-PS...
— For wall mounting only. — Universal for wall or 2" pipe mounting. — Cable entry for I/P signal converter with the "flameproof (enclosure) (Ex d)" type of protection. TEIP11, TEIP11-PS | 42/18-46-EN Rev. L 9...
Mounting the unit. NOTICE Installation location requirements Prior to installation, check to ensure that the TEIP11 and TEIP11-PS I/P signal converters meet the measurement and safety requirements applicable at the installation location (see section "Additional documents" on page 14). 6.1.1 Control room housing unit for rail mounting This model is snap-mounted on a DIN top-hat rail.
A stainless steel mounting bracket is available as an accessory for installation. The mounting bracket is available in two designs: — For wall mounting only. — Universal for wall or 2" pipe mounting. TEIP11, TEIP11-PS | 42/18-46-EN Rev. L 11...
4 bar (60 psi). This could result in mechanical damage to the unit. NOTICE — The TEIP11 and TEIP11-PS I/P signal converters may only be operated with instrument air that is free of oil, water, and dust.
— This product is not subject to WEEE Directive 2012/19/EU All devices delivered to ABB must be free from any hazardous or relevant national laws (e.g. ElektroG in Germany). materials (acids, alkalis, solvents, etc.).
Which substances have come into contact with the device? We hereby state that the devices / components shipped have been cleaned and are free from any dangerous or poisonous substances. Town/city, date Signature and company stamp TEIP11, TEIP11-PS | 42/18-46-EN Rev. L 15...
Page 19
TEIP11, TEIP11-PS | 42/18-46-EN Rev. L 19...
Page 20
Howard Road, St. Neots notice. Cambridgeshire, PE19 8EU With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or Tel: +44 (0)870 600 6122 possible lack of information in this document.