Table of Contents
Advertisement
—
A B B M E A S U R E M E N T & A N A L Y T I C S | O P E R A T I N G I N S T R U C T I O N
TEIP11, TEIP11-PS
I/P signal converter
Introduction
—
TEIP11
TEIP11-PS
I/P signal converter for controlling pneumatic
actuators or conventional positioners for valve
positioning.
Additional Information
Additional documentation on TEIP11, TEIP11-PS is
available for download free of charge at
www.abb.com/positioners.
Alternatively simply scan this code:
Advertisement
Table of Contents
Related Manuals for ABB TEIP11
Summary of Contents for ABB TEIP11
- Page 1 I/P signal converter Introduction Additional Information — TEIP11 TEIP11-PS I/P signal converter for controlling pneumatic Additional documentation on TEIP11, TEIP11-PS is actuators or conventional positioners for valve available for download free of charge at positioning. www.abb.com/positioners. Alternatively simply scan this code:...
-
Page 2: Table Of Contents
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Table of contents Change from one to two columns Commissioning ............15 Safety ................3 General information and instructions ........3 Maintenance ............. 15 ... -
Page 3: General Information And Instructions
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M 1 Safety hange from one to two columns Warnings General information and instructions The warnings in these instructions are structured as follows: These instructions are an important part of the product and must be retained for future reference. -
Page 4: Intended Use
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M … 1 Safety Warranty provisions Intended use I/P signal converters for standard signals TEIP11 and TEIP11-PS Using the device in a manner that does not fall within the scope are used to control pneumatic actuators or pneumatic... -
Page 5: Use In Potentially Explosive Atmospheres
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Change from one to two columns 2 Use in potentially explosive atmospheres Change from one to two columns DANGER Thermal data T4: –40 °C < Tamb < 85 °C Risk of explosion when used with combustible gases T5: –40 °C <... -
Page 6: Fm / Csa
25.5 V 3.825 W Special conditions The I/P signal converter TEIP11-PS Doc. 901068 or TEIP11-PS Doc. 901069 must be set up outdoors as a pneumatic power supply when used with combustible gases. The supplied gas must be kept sufficiently free of air and oxygen to prevent a potentially explosive atmosphere from forming. -
Page 7: Installation Instructions
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Installation instructions The installation, commissioning, maintenance and repair of Requirements for operation with the ‘flameproof devices in potentially explosive atmospheres must only be (enclosure)’ (Ex d) type of protection carried out by appropriately trained personnel. Works may be... -
Page 8: Design And Function
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M 3 Design and function Force balancing takes place at the lever arm, which is mounted The I/P signal converter converts standard electrical signals, e.g. with a tension band. The coil and yoke generate a magnetic field 4 to 20 mA to 0.2 to 1 bar (3 to 15 psi). -
Page 9: Designs
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Designs Control room housing unit for block mounting The control room housing unit for block mounting enables you to install a number of converters in a small space. This design features central air supply via connection block and stop valves in the air connectors of the integrated signal converter. -
Page 10: Product Identification
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M 4 Product identification 5 Transport and storage Name plate Inspection Check the devices immediately after unpacking for possible damage that may have occurred from improper transport. Details of any damage that has occurred in transit must be recorded on the transport documents. -
Page 11: Installation
Control room housing unit for block mounting Installation location requirements For this design, a special connection block is used to mount the Prior to installation, check to make sure that the TEIP11 and unit. TEIP11-PS I/P signal converters meet the measurement and safety requirements applicable at the installation location (see Additional documents on page 16). -
Page 12: Aluminum / Stainless Steel Field Mount Housing
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M … 6 Installation … Mounting Aluminum / stainless steel field mount housing Installation instructions Position the housing so that the cable gland is facing The sturdy housing unit can be installed outdoors without downwards or sideways, to prevent humidity from penetrating protection. -
Page 13: Electrical Connections
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Electrical connections WARNING Cable glands The field mount housings feature a PG 11 cable entry. Risk of injury due to live parts! When the housing is open, contact protection is not provided Aluminum or stainless steel field mount housing and EMC protection is limited. -
Page 14: Pneumatic Connections
Pneumatic connections Note Pneumatic data TEIP11 • The TEIP11 and TEIP11-PS I/P signal converters may only be Instrument air operated with instrument air that is free of oil, water, and Free of oil, water, and dust acc. to DIN/ISO 8573-1 dust. -
Page 15: Commissioning
If the tolerance limits are exceeded, this can be corrected All devices delivered to ABB must be free from any hazardous through adjustment. materials (acids, alkalis, solvents, etc.). Two adjustment screws are used for the adjustment process. -
Page 16: Recycling And Disposal
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M 10 Recycling and disposal Note Products that are marked with the adjacent symbol may not be disposed of as unsorted municipal waste (domestic waste). They should be disposed of through separate collection of electric and electronic devices. -
Page 17: Appendix
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Change from two to one column 12 Appendix Return form Statement on the contamination of devices and components Repair and/or maintenance work will only be performed on devices and components if a statement form has been completed and submitted. -
Page 18: Control Document
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M … 12 Appendix Control Document Connection diagram 900842 FM... - Page 19 TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M...
-
Page 20: Connection Diagram 900842 Csa
TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M … 12 Appendix … Control Document Connection diagram 900842 CSA... - Page 21 TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M...
- Page 22 TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Notes...
- Page 23 TEIP11, TEIP11-PS I/P SIGNAL CONVERTER | OI/TEIP11/TEIP11-PS-EN REV. M Notes...
- Page 24 We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.