Power Supply With Rechargeable Batteries - Philips PM2517E Service Manual

W i t h o u t r a n g i n g
F u n c t i o n
R e s p o n s e t i m e
V ;:-: , A:-: ,
"C
a T
m a x . 1 s e c .
max. 1 sec.
m a x . 1 s e c .
Response time
Recovery time
Data hold
C l i m a t i c c o n d i t i o n s
Power supPlY
O p e r a t i o n
BatterY life-time
Mechanical data
W i t h r a n g l n g
C a b i n e t
W e i g h t
F u n c t i o n
R e s p o n s e t i m e
f,)
m a x . 3 s e c .
max. 5 sec.
m a x . 6 s e c .
m a x . 3 s e c .
V i a p r o b e i n p u t
R e f e r e n c e l e m p e r a t u r e 1 2 3
o C
! 2 o C
Rate range of use
-16 og ' + 55 oC
S p e c i f i e J r a n g e
O o c
' 4 5 o c
Limit range of srorage
-40 oC
* 70 oC
ancl transporr
Relative humidity (ex- 20y"
80"/"
c l u d i n g c o n d e n s a t i o n )
4 x 1 . 5 V b a t t e r i e s , e . g . t y p e s : P h i l i p s R
' 1 4 T R
4x 1 .5 V Nicd rechargeable batteries; refer
tc 1'3
( s p e c i a l r e q u i r e m e n t s ) .
e . g t Y p e s : D E A c ' R S 1 5
G E N E I T A L E L E C T R I C , G C T 1 . 5 S B
F U R U K A W A , S 1 0 4
External 9 V Power suPPlY PIM 9218
O F F
ifnt!o
av, display for 40 sec if DISPLAY switch
is activated
O N ,
c o n t i n u o u s d i s p l a y
3 0 h o u r s ( c o n t i n u o u s d i s P l a V )
D i m e n s i o n s L e n g t h
1 6 5 m m
W i d t h
I 1 5 m m
H e i g h t
5 0 m m
l\4aterial
ABS
=0.7 kg (without batteries)
1 . 3 .
P O W E R S U P P L Y W I T H R E C H A R G E A B L E B A T T E R I E S
The pl\,4 2517 delivered from the factory is
wired for use with dry-c€ll batteries
power supplv or for a I V
external power supplY using the PN4 9218' For
rechargeable batteries power supply the
wiring inside the
i n s t r u m e n t h a s t o b e m o d i f i e d T h e c h a r g i n g
t i m e i s 1 8 h o u r s '
Note:
when the instrument ßwired for rechargeable
battery power supply , drY+ell batteries should
not
Tn!*noi un*"'
power supply will damage the dry'cell batteries'
When dry'cell batteries are used
again, the instrument sllould be wired to its original
state'
For changing the wiring ploceed as {ollows:
-
Remove the batterY cover
-
Remove the two special nuts situated under the
battery cover
- Pull the rear cover from the Instrumenr'
Note:
Take care that the wimg to the battery compartment
does not break' When mounting the rear
cover
again take care that the wiring is fitted
properly