Pioneer SPH-C19BT Quick Start Manual

SMARTPHONE RECEIVER
SPH-C19BT
Quick start guide
CRB5151-B
• Consult your dealer if installation requires drilling
Subwoofer (4 Ω) × 2
of holes or other modifications to the vehicle.
Orange/white
• Do not install this unit where:
Connect to a car's illumination signal.
− it may interfere with operation of the vehicle.
Violet/white
− it may cause injury to a passenger as a result of
Of the two lead wires connected to the back
a sudden stop.
lamp, connect the one in which the voltage
• Install this unit away from hot places such as near
changes when the gear shift is in the REVERSE
the heater outlet.
(R) position. This connection enables the unit
• Optimum performance is
to sense whether the car is moving forwards or
obtained when the unit is
backwards.
installed at an angle of less
Light green
than 45°.
Used to detect the On/Off status of the parking
• When installing, to ensure proper heat dispersal
brake. This lead must be connected to the power
when using this unit, make sure you leave ample
supply side of the parking brake switch.
space behind the rear panel and wrap any loose
NOTE
cables so they are not blocking the vents.
Change the initial menu of this unit. Refer to
[SP-P/O] in the INITIAL settings. The subwoofer
output of this unit is monaural.
Leave ample
5 cm
Power amp (sold
space
separately)
5 cm
Perform these connections when using the optional
amplifier.
DIN mount installation
1
Insert the supplied mounting sleeve into
the dashboard.
2
Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°)
into place.
System remote control
Connect to blue/white cable.
Power amp (sold separately)
Connect with RCA cables (sold separately)
To front output
Front speaker
To rear output or subwoofer output
Rear speaker or subwoofer Dashboard
Mounting sleeve
• Make sure that the unit is installed securely
Installation
in place. An unstable installation may cause
skipping or other malfunctions.
Important
• Check all connections and systems before final
installation.
• Do not use unauthorized parts as this may cause
malfunctions.

Basic operation

SPH-C19BT
USB port
Smartphone holder Application launch
Display window
Source (music)/OFF Detach button
Navigation Phone
Voice recognition Message
Operating the smartphone holder
WARNING
• Detach the smartphone from the holder while driving under bad road conditions since the smartphone
may fall from the holder.
• Do not leave the smartphone attached onto the holder.
• Do not use the holder if you experience difficulty when attaching the smartphone onto the holder.
• Do not operate the holder or smartphone while driving.
• Be careful not to get your hands and fingers caught in the moving parts while operating the holder.
• Do not attach the smartphone to the holder in a location where it may drop on the driver's feet.
• Do not set the holder near the air conditioner vent.
• Make sure that nothing affects the operation of the air bags or vehicle operating systems, safety feature or
hazard lamps.
• PIONEER IS NOT RESPONSIBLE AND DISCLAIMS LIABILITY FOR ANY DAMAGES CAUSED THROUGH USE OF
THE PRODUCT OR VEHICLE.
Removing the smartphone holder
1
Detach the front panel.
2
Pull out the holder by holding the anti slip portion on the edge of the
holder until the holder is completely visible.
Making a connection with Pioneer Smart Sync
Pioneer Smart Sync is the application that intelligently brings
your maps, messages, and music together in the vehicle.
For details on what operations are available on the application, see the application's help
section.
WARNING WARNING
Do not attempt to operate the application while driving. Make sure
to pull off the road and park your vehicle in a safe location before
attempting to use the controls on the application.
1
Connect this unit with the mobile device via Bluetooth (refer to
"Bluetooth connection").
Pioneer Smart Sync on the iPhone/Android device starts
automatically.
Pioneer Smart Sync connection via wired connection
You can also make the Pioneer Smart Sync connection via USB connection.
1
Press and hold to display the main menu.
2
Press to select [SYSTEM], then press to confirm.
3
Press to select [APP CTL], then press to confirm.
4
Press to select [WIRED], then press to confirm.
Pioneer Smart Sync on the iPhone/Android device starts
automatically.
This guide is intended to guide you through the basic functions of this unit.
For details, please refer to the Owner's manual stored on the website.
http://www.pioneerelectronics.com/support

Before You Start

Thank you for purchasing this PIONEER product
To ensure proper use, please read through this guide before using this product. It is especially important
that you read and observe WARNINGS and CAUTIONS in this guide. Please keep the guide in a safe and
accessible place for future reference.
WARNING
• Do not attempt to install or service this product by yourself. Installation or servicing of this product
by persons without training and experience in electronic equipment and automotive accessories
may be dangerous and could expose you to the risk of electric shock, injury or other hazards.
• Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle in a
safe location before attempting to use the controls on the device.
• Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered
with items (such as papers, floor mat, cloths).
CAUTION
• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result. Also,
damage to this unit, smoke, and overheating could result from contact with liquids.
• Always keep the volume low enough to hear outside sounds.
• This product is evaluated in moderate and tropical climate condition under the Audio, video and similar
electronic apparatus - Safety requirements, IEC 60065.
If you experience problems
Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service
Station.
When not using the supplied

Installing the microphone

mounting sleeve
The microphone should be placed directly in front
1
Determine the appropriate position where
of the driver at a suitable distance to pick up their
the holes on the bracket and the side of
voice clearly.
the unit match.
CAUTION
It is extremely dangerous to allow the microphone
lead to become wound around the steering column
or shift lever. Be sure to install the microphone in
such a way that it will not obstruct driving. It is
2
Tighten the screws on each side.
recommended to use the clamps (sold separately)
to arrange the lead.
NOTE
Depending on the vehicle model, the microphone
cable length may be too short when you mount the
microphone on the sun visor. In such cases, install
the microphone on the steering column.
Truss screw (5 mm × 9 mm)
To install on the sun visor
Mounting bracket
Dashboard or console
1
Fit the microphone lead into the groove.
Removing the unit (installed with the
supplied mounting sleeve)
1
Remove the trim ring.
2
Install the microphone clip on the sun
visor.
Trim ring
Lowering the sun visor reduces the voice
• Releasing the front panel allows easier access
recognition rate.
to the trim ring.
• When reattaching the trim ring, point the side
with the dent part up.
2
Insert the supplied extraction keys into
both sides of the unit until they click into
place.
3
Pull the unit out of the dashboard.
Microphone clip
CAUTION
Never pull up the holder until the holder is completely visible.
3
Pull up the holder vertically.
CAUTION
Make sure that the line can be seen when the holder is pulled up vertically.
NOTE
The automatic connection may fail depending on your mobile device. In that case, press and
hold .
TIP
Once the Pioneer Smart Sync connection is made between the unit and the mobile device,
you can pair from the application on the mobile device from the next time.

Connections

WARNING
• When speaker output is used by 4 channels, use
speakers rated over 50 W (maximum input power)
and between 4 Ω to 8 Ω (impedance value). Do
not use 1 Ω to 3 Ω speakers for this unit.
• When rear speaker output is used by a 2 Ω
subwoofer, use speakers rated for over 70 W.
* Please refer to connections for a connection
method.
• The black cable is ground. When installing this
unit or power amp (sold separately), make sure
to connect the ground wire first. Ensure that
the ground wire is properly connected to metal
parts of the car's body. The ground wire of the
power amp and the one of this unit or any other
device must be connected to the car separately
with different screws. If the screw for the ground
wire loosens or falls out, it could result in fire,
generation of smoke or malfunction.
Two devices connected to the car • When this unit is on, control signals are sent
separately (ground wires)
• Never connect the blue/white cable to the power
Metal parts of
car's body
*1 Not supplied for this unit
Important
• The graphical symbol
• When installing this unit in a vehicle without an
ACC (accessory) position on the ignition switch,
failure to connect the red cable to the terminal
that detects operation of the ignition key may
result in battery drain.
ACC position No ACC position
• Use this unit with a 12-volt battery and negative
grounding only. Failure to do so may result in a fire
or malfunction.
• To prevent a short-circuit, overheating or
malfunction, be sure to follow the directions
below.
− Disconnect the negative terminal of the battery
before installation.
To install on the steering
column
1
Slide the microphone base to detach it
from the microphone clip.
Microphone
Microphone clip
Microphone base
2
Install the microphone on the rear side of
the steering column.
Microphone
lead
Groove
Double-sided tape
4
Attach the front panel to the unit.
Attaching the smartphone to the holder
CAUTION
• Depending on the shape of the smartphone, smartphone case or cover, it may not be attachable to the
holder.
• Be careful not to pinch your fingers in the holder.
Compatible smartphone size
H: 58 mm - 170 mm
W: 58 mm - 87 mm
D: 4 mm - 10 mm
Weight: under 0.25 kg
1
Hook the smartphone on the upper arm and then push it into the
lower arm.
− Secure the wiring with cable clamps or adhesive This unit
tape. Wrap adhesive tape around wiring that
comes into contact with metal parts to protect
the wiring.
− Place all cables away from moving parts, such as
the shift lever and seat rails.
− Place all cables away from hot places, such as
near the heater outlet.
− Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
− Cover any disconnected cable connectors with
insulating tape.
Power cord input
− Do not shorten any cables.
Microphone input
− Never cut the insulation of the power cable of
Microphone 3 m
this unit in order to share the power with other
Rear output or subwoofer output
devices. The current capacity of the cable is
Front output
limited.
Antenna input
− Use a fuse of the rating prescribed.
Parking sensor input
− Never wire the negative speaker cable directly
UART adaptor (supplied with parking seonsor
to ground.
unit (ND-PS1)) can be connected (sold
− Never band together negative cables of multiple
separately).
speakers.
Fuse (10 A)
Wired remote input
through the blue/white cable. Connect this cable
Hard-wired remote control adapter can be
to the system remote control of an external power
connected (sold separately).
amp or the vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the vehicle is
Power cord
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
Perform these connections when not connecting a
terminal of an external power amp. Also, never rear speaker lead to a subwoofer.
connect it to the power terminal of the auto
antenna. Doing so may result in battery drain or
a malfunction.
placed on the
product means direct current.
2
Slide the lower arms position to avoid hitting the lower arm and
smartphone buttons against each other.
NOTES
• Make sure that the smartphone is held properly on the holder.
• When the smartphone buttons come in contact with the upper or lower arms, adjust the smartphone's
position or turn the smartphone upside down.
Bluetooth connection
Up to two Bluetooth telephones can be connected simultaneously.
CAUTION
• Do not use mobile phone while driving.
Important
If ten or more Bluetooth devices (e.g. a phone and separate audio player) are connected, they
may not work properly.
1
Turn on the Bluetooth function of the device.
2
Select the unit name shown in the device display.
3
Make sure the same 6-digit number appears on this unit and the
device.
4
Select [Y].
Perform these connections when using a subwoofer
without the optional amplifier.
Important
above, two 4 Ω subwoofers wired
In the case of
in parallel will represent a 2 Ω load.
To power cord input
Left
Right
Front speaker
Rear speaker
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black (chassis ground)
Connect to a clean, paint-free metal location.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by the ignition
switch (12 V DC).
Blue/white
Connect to the system control terminal of
the power amp or auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Subwoofer (4 Ω)
When using a subwoofer of 2 Ω, be sure to
connect the subwoofer to the violet and violet/
black leads of this unit. Do not connect anything
to the green and green/black leads.
Not used.