Table of Contents
Advertisement
Operating Instructions
High Resolution 38cm/15" LCD-Monitor SCD 1597
Operating Instructions
SCD 1597 R
6AV8100-1CA00-0AA0
(Int.ID:6GF6230-6MA)
SCD 1597 RT
6AV8100-1CB00-A00A
(Int.ID:6GF6230-6MB)
SCD 1597 R8S
6GF6232-6MA
© © © © Copyright Siemens AG
DOC-Nr.: B3 0038 D4.DOC
LCD-Monitor SCD 1597-R/RT/R8S
Page 1 / 22
Advertisement
Table of Contents
Related Manuals for Siemens SCD 1597
Summary of Contents for Siemens SCD 1597
- Page 1 Operating Instructions High Resolution 38cm/15" LCD-Monitor SCD 1597 Operating Instructions SCD 1597 R 6AV8100-1CA00-0AA0 (Int.ID:6GF6230-6MA) SCD 1597 RT 6AV8100-1CB00-A00A (Int.ID:6GF6230-6MB) SCD 1597 R8S 6GF6232-6MA © © © © Copyright Siemens AG DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 1 / 22...
- Page 2 Operating Instructions No part of this document may be reproduced or transmitted without express permission. Violations will result in prosecution. All rights reserved. 1999 All rights reserved DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 2 / 22...
-
Page 3: Table Of Contents
Input Signals......................21 4.7. EU Declaration of Conformity on EMC ..............21 Figures Figure 1: Dimensions of the SCD 1597-R/RT/R8S .............. 9 Figure 2: VGA-interface ..................... 11 Figure 3: Location of the operation and alignment elements ..........13 DOC-Nr.: B3 0038 D4.DOC... -
Page 4: Overview
At the press of a button, the monitor performs these alignments automatically. The SCD 1597-R/RT/R8S is equipped with an active 15.0” TFT display module with a maximum resolution of 1024x768 pixels. The integrated power management system VESA DPMS, allows a significant reduction in power consumption when the synchronisation signal from the computer has been switched off, compared with that under “normal”... -
Page 5: Layout Of This Handbook
Chapters are clearly arranged according to subject. In detail, the chapters are arranged as follows: • Chapter 1 Introduction This chapter provides a brief description of the SCD 1597-R/RT/R8S, including its properties, application areas and special features. • Chapter 2 Installation This chapter is mainly concerned with preparing the LCD-monitor for use, its installation and cabling. -
Page 6: Warnings And Safety Notes
Scouring powders and solvents must never be allowed to come in contact with the unit. The inside of the unit is to be cleaned by qualified service technicians only. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 6 / 22... -
Page 7: Instructions For Handling Assemblies Susceptible To Electrostatic Shock
Instructions for Handling Assemblies Susceptible to Electrostatic Shock Most of the assemblies within the SCD 1597-R/RT/R8S LCD-monitor contain components which can be destroyed by electrostatic voltages. It is also possible for the assemblies to be damaged in such a way that total failure does not occur. -
Page 8: General Installation
Have the delivery note number, serial number and a description of the deficiency to hand. The original packaging should be kept for future transportation. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 8 / 22... -
Page 9: Installing The Lcd-Monitor
– Safety problems Ergonomics – Mechanical Installation – Figure 1: Dimensions of the SCD 1597-R/RT/R8S 1) bei SCD 1597-R8S = 279,4 mm 2) bei SCD 1597-R8S = 354,8 mm DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 9 / 22... -
Page 10: Installation Of Ac/Dc-Power Supply Unit Or 24V-Dc/Dc-Converter
Thermal Problems In order that the LCD-monitor maintains an optimum operating temperature while in use, air must be allowed to circulate freely around the SCD 1597-R/RT/R8S enclosure. It is particularly important that the rear of the system is kept free. -
Page 11: Cable Connections And Pin Assignments
Video input RED Video input GREEN Video input BLUE Not used Not used GND (RED) GND (GREEN) GND (BLUE) Not used Not used Not used H-Sync. V-Sync. Not used DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 11 / 22... -
Page 12: Electrical Installation
Operating Instructions Power Supply Power is supplied to the SCD 1597-R/RT/R8S via a standard power connector on the rear of the unit. Name Description Voltage input GND +12V Power supply +12VDC 2.4. Electrical Installation Before connecting the SCD 1597-R/RT/R8S to the power supply, a check should be carried out as to whether the VGA connector is plugged in properly and that the screws tightened. -
Page 13: Operation And Alignment
Figure 1 on page 31 and are used for the OSD-menu. Compartment for VGA-interface power supply Touchscreen (option) power supply unit Figure 3: Location of the operation and alignment elements front rear ↓ DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 13 / 22... - Page 14 Menu key calls up the OSD menu proceeds to the next menu point. Sub menu key selects a sub menu point DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 14 / 22...
-
Page 15: Osd Menu Structure
“UP” and “DWN” keys. Colour temperature Position Status Brightness Frequency Phase Kontrast Scaling Sharpness Zooming Language Utilities The individual functions and settings are described below. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 15 / 22... -
Page 16: Brightness / Contrast
This menu point allows the picture to be shifted in the horizontal and vertical directions. 3.2.6. Scaling This contains four sub menu points which influence the manner in which images of greater or lesser resolution than that of the display are represented. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 16 / 22... -
Page 17: Horizontal / Vertical Pan
This is a vertical linearity setting for the picture height, i.e., if the value is negative, the picture is compressed more at the vertical edges and stretched more in the middle. A positive value has the opposite effect. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 17 / 22... -
Page 18: Sharpness
If the DPMS is not active then the “NO signal” message stays on the screen until a valid video signal is applied to the monitor. Auto Source Select This has no function. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 18 / 22... -
Page 19: Automatic Alignment
The brightness, contrast, frequency, phase and picture position are all automatically adjusted. If, due to insufficient picture information, the automatic alignment does not work correctly, the parameters can all be adjusted manually as described above. DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 19 / 22... -
Page 20: Technical Data
-25 to +60°C Humidity max. 95% (non condensing) 4.4. Protection Protection class Front IP65 Front screen none 4.5. Enclosure Weight approx. 3.9kg Enclosure material steel Enclosure colour light basic DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 20 / 22... -
Page 21: Input Signals
No. 73/23/EWG No. 93/68/EWG Harmonised standards EN 55022 Class A Edition 05/1995 Interference emissions used +A1/EN55022/A1 Edition 08/1994 EN 50082-2 Edition 02/1996 Interference resistance EN 60950 Edition 11/1997 Safety DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 21 / 22... - Page 22 Operating Instructions DOC-Nr.: B3 0038 D4.DOC LCD-Monitor SCD 1597-R/RT/R8S Page 22 / 22...