Related Manuals for LG MultiVision SPM42C4-WP
Summary of Contents for LG MultiVision SPM42C4-WP
- Page 1 Owner's Manual MultiVision Mounting Bracket Please read the safety information carefully before using the product. SPM42C4-WL SPM42C4-WP P/NO : MFL63640518 (1207-REV00)
- Page 2 MultiVision Mounting Bracket MultiVision Mounting Bracket-Landscape MultiVision Mounting Bracket-Portrait SPM42C4-WL SPM42C4-WP Accessories 4 Guide Spacer 4 Guide Spacer Fixing 4 Bracket Fixing Screws 4 Nuts Screws (M6X80mm) (M6X35mm) Owner's Manual Wrench 4 Supporter Connection Supporter Connection Fixing Screws (SPM42C4-WL Only) (M4X8mm)
-
Page 3: Safety Precautions
Safety Precautions - If you are a professional installer, please read this manual carefully before installing the product. - After installing the product according to the manual, ensure that the user also reads the manual carefully. After reading the manual, please keep it handy for future reference. Warning The product should be installed by a qualified professional The product should be installed where its weight can be... - Page 4 Transportation method for panel protection When moving or lifting the monitor, read the following to prevent the monitor from being When transporting the monitor, do not expose scratched or damaged and for safe transportation the monitor to jolts or excessive vibration. regardless of its type and size.
-
Page 5: Storage Method For Panel Protection
Storage method for panel protection <Correct method> Panel Cushion If the product needs to be When laying down the prod- set upright, hold both sides uct, lay a cushion on a flat of the product, and tilt back- floor, and put the product on ward carefully for the panel it with the panel of the prod- not to touch the floor. -
Page 6: Before Installation
The illustration depicts a landscape installation, but the procedure is identical to that of a portrait installation. Before Installation * Do not use this product for purposes other than to attach the monitor to the wall. * Be careful when installing and using the bracket to prevent product damage and safety hazards. * If the instructions in the manual are unclear, stop the installation and contact the service center. - Page 7 - Join the brackets each other as shown below using the connect supporters and screws. - When the brackets are attached, unscrew the locking bolts A and B to adjust the sets vertically and horizontally before mounting them. Locking bolt for vertical adjustment Locking bolt for...
- Page 8 Verifying Where the Brackets Are Fixed Refer to the following illustration to fix the brackets according to the type. MultiVision Wall Bracket-Landscape MultiVision Wall Bracket-Portrait SPM42C4-WL SPM42C4-WP The bracket may be distorted, depending on the A bolt flatness of the wall. Adjust the flatness of the bracket using the A bolts attached to it.
-
Page 9: Dip Switch Setting
Dip switch setting Factory reset monitor #3 monitor #1 monitor #4 * There is a switch on the inside cover. monitor #2 monitor #5 How to Attach the Product and Bracket - Two or more people are needed to install the product. Place the product assembled with the guide spacers, as illustrated with the arrow. - Page 10 Set Arrangement The procedure is based on 3X3 installation. Set Arrangement step : 8 → 5 → 2, 7 → 4 → 1, 9 → 6 → 3 1. Mount set 8 to the wall mounting bracket as shown below and adjust it vertically and horizontally before fastening A locking bolts.
- Page 11 2. Mount set 5, then remove the module-protecting Cover on sets 8 and 5. Remove the module-protecting Cover. (The protective Cover is attached on all four sides; only re- move fi rst the Cover on the sides where the sets meet.) Insert 4 Guide pins as shown in the fi...
- Page 12 - Mount set 2 in the same way as set 5 is mounted. 4. Fix the top set (i.e., set 2 shown below) with the locking bolts so that it does not move vertically. Remove the module-protecting Cover. (The protective Cover is attached on all four sides; only remove fi...
- Page 13 6. After adjusting the gap (seam) as explained above, fi nish the assembly by sliding the left and right three sets as shown below. * To minimize the gap between the joined sets, tighten the left and right sliding locking screws at the bottom of the wall mounting brackets.
-
Page 14: How To Service
How to Service 1. Slide sets 3, 6, 9 to the right and sets 1, 4, 7 to the left. Make sure that the left and right sliding fi xing locks are released. 2. Move sets 2 and 5 to the position B as shown below. Move set 8 to the position A and pull it out. CAUTION Make sure that sets 2 and 5 are not pulled out at the position A when moving them to the service position. -
Page 15: Product Specifications
Product Specifications 1325.5 Model Name SPM42C4-WL SPM42C4-WP Width (mm) 1426 1426 Height (mm) Depth (mm) 1006 1006 Gross Weight (kg) - Page 16 The model name and serial number are located on the back and side of the product. Please make a note of these below. Model Name Serial Number...